2003 FORD MUSTANG brake

5. Lift the caliper off the anchor plate (2B292).
6. Inspect the disc brake caliper.
zIf leaks or damaged boots are found, disassembly is required. For additional information,
refer to Caliper in this section.
Installation 1. Make sure the anti- rattle spring is correctly positioned in the caliper. Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2.
CAUTION: Make sure guide pin boots are correctly seated or damage to guide pins
can occur.
Install the disc brake caliper. 1. Hold the guide pins stationary.
2. Install the caliper bolts.
3. NOTE: Use new copper washers.
Install the front brake hose. Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Bleed the caliper. For additional information, refer to
Section 206 - 00 .
5. Install the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
6. Fill the brake master cylinder reservoir (2K478) with clean High Performance DOT 3 Brake Fluid C6AZ- 19542- AB or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25- A. Install
brake master cylinder filler cap (2162).
7. Check the brake system operation. Klj . 4 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Brake Caliper —
Cobra
Removal 1. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
2. Remove the tire and wheel assembly. For additional information, refer to Section 204 - 04 .
3. Remove the caliper locating pin E- clip.
4. Remove the caliper locating pin.
5. Remove the front brake flow bolt. 6. Remove the caliper. SECTION 206-
03: Front Disc Brake 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

7. Remove the brake pads.
Installation 1. NOTE: Use new copper washers on front brake flow bolt.
Follow the removal procedure in reverse order. zBleed the caliper. For additional information, refer to Section 206 - 00 . Klj . 2 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Brake Caliper Anchor Plate —
Cobra
Removal 1. Remove the pads. For additional information, refer to Brake Pads — Cobra in this section.
2. Remove the anchor plate bolts.
Installation 1. Follow the removal procedure in reverse order.
SECTION 206-
03: Front Disc Brake 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Brake Caliper Anchor Plate
Removal
1. Remove the pads. For additional information, refer to Pads in this section.
2. Remove the anchor plate (2B292). 1. Remove and discard the anchor plate bolts.
2. Remove the anchor plate.
Installation 1. CAUTION: Use correct type and length bolts.
Follow the removal procedure in reverse order. zInstall new anchor plate bolts.
SECTION 206-
03: Front Disc Brake 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Disc
Removal
1. Remove the front disc brake caliper anchor plate (2B292). For additional information, refer to Brake Caliper Anchor Plate in this section.
2. Match mark the hub (1104) and the brake disc (1125).
3. If necessary, remove and discard the keeper nuts.
4. NOTE: If the brake disc cannot be easily removed, apply Rust Penetrant and Inhibitor F2AZ-
19A501- A or equivalent meeting Ford specification ESR-M99C56- A to the mating surfaces.
Remove the brake disc from the hub.
Installation 1. Clean rust and foreign material from the mating surfaces of the hub and brake disc. zUse Metal Brake Parts Cleaner F3AZ-19579- SA or equivalent to clean the brake disc
and hub.
2. Apply High Temperature Nickel Anti- Seize Lubricant F6AZ-9L494-AA or equivalent meeting Ford specification ESE - M12A4 - A to the hub flange. SECTION 206-
03: Front Disc Brake 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...