2003 DAEWOO MATIZ coolant temperature

1F–68 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F100
DIAGNOSTIC TROUBLE CODE (DTC) – P0113 INTAKE AIR TEMPERATURE
SENSOR HIGH VOLTAGE
Circuit Description
The Intake Air Temperature (IAT) Sensor uses a therm-
istor to control the signal voltage to the engine control
module (ECM). The ECM supplies a 5 volt reference
voltage and a ground to the sensor . when the air is cold,
the resistance is high ; therefore IAT sensor signal volt-
age will be high. If the intake air is warm, resistance is
low ; therefore the IAT sensor signal voltage will be low.
Conditions for Setting the DTC

The engine rum time is greater than 3 seconds.

IAT voltage is greater than 4.99V.
Action Taken when the DTC Sets

Emission related.

“Armed” after two trip with a fail.

“Disarmed” after one trip with a pass.

MIL on if failure is detected in three consecutive trips.

Stores a History DTC on the third consecutive with a
fail (The DTC will be armed after the second fail).
Stores a Freeze Frame on the third consecutive trip
with a fail (if empty).

The ECM will default to last valid value for intake air
temperature. The scan tool will not show the de-
faulted value.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
If the vehicle is at ambient temperature, compare the
IAT sensor to the engine coolant temperature (ECT)
sensor. The IAT sensor and the ECT sensor should be
relatively close to each other.
Use the temperature vs. Resistance Values table to
evaluate the possibility of a skewed sensor. Refer to
“Temperature vs. Resistance” in this Section.

1F–72 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F110
DIAGNOSTIC TROUBLE CODE (DTC) – P0117 ENGINE COOLANT
TEMPERATURE SENSOR LOW VOLTAGE
Circuit Description
The Engine Coolant Temperature sensor (ECT) uses a
thermistor to control the signal voltage to the engine
control module (ECM).
The ECM supplies a voltage on the signal circuit to the
sensor. When the engine coolant is cold, the resistance
is high; therefore the ECT signal voltage will be high.
As the engine warms, the sensor resistance becomes
less, and the voltage drops. At normal engine operating
temperature, the voltage will be between 1.5 and 2.0
volts at the ECT signal terminal.
The ECT sensor is used to the following items:

Fuel delivery.

Lock Up Clutch (LUC).

Ignition.

Evaporator Emission (EVAP) Canister Purge Valve.

Electric cooling fan.
Conditions for Setting the DTC

This DTC can be stored in “key-on” status.

The engine rum time is greater than 3 seconds.

A low voltage condition exits.

ECT voltage is less than 0.03V.
Action Taken when the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.
The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.

A history DTC is stored.

The coolant fan turns ON.

The ECM will default to 20°C(68°F)for the first 60
seconds of the engine run time, and then
92°C(198°F).

the scan ttol will not show the defaulted value.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
After the engine has started, the ECT should rise steadi-
ly to about 90°C(194°F) then stabilize when the thermo-
stat opens.
Use the temperature vs. resistance values table to eval-
uate the possibility of a skewed sensor. Refer to “Te m -
perature vs. Resistance” in this Section.

ENGINE CONTROLS 1F–73
DAEWOO M-150 BL2
DTC P0117 – Engine Coolant Temperature Sensor Low Voltage
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Connect the scan tool to the data link connector
(DLC).
2. Run the engine until it reaches operating
temperature.
Does the scan tool show the ECT sensor reading
within the value specified?
80~110°C
(176~230°F)
Go to
“Diagnostic
Aids”
Go to Step 3
3
1. Turn the ignition switch to LOCK.
2. Disconnect the ECT sensor connector.
3. Turn the ignition switch to ON.
Does the scan tool show the IAT sensor reading
within the value specified?
≥-30°C(-22°F)Go to Step 4Go to Step 6
4
1. Jumper the ECT sensor signal circuits at terminal
A and B.
2. Turn the ignition switch to ON.
Does the scan tool show the ECT sensor reading
within the value specified?
≥120°CGo to Step 5Go to Step 6
5
1. Replace the ECT sensor.
2. Clear any DTCs from the ECM.
3. Perform the diagnostic system check.
Is the replacement complete?
–
System OK
–
6
Measure the voltage between ECT terminal A and
ground.
Does the voltage measure within the value
specified?
4.5–5.0VGo to Step 7Go to Step 8
7
1. Turn the ignition switch to LOCK.
2. Disconnect the ECM wiring connector.
3. Check for a faulty connector or terminals at the
ECT sensor connectors and ECM connectors for
short to ECM reference voltage.
Is the problem found?
–
Go to Step 9Go to Step 8
8
1. Turn the ignition switch to LOCK.
2. Repair the wire of the connector terminals as
needed.
3. Clear any DTCs from the ECM.
4. Run the engine until it reaches operating
temperature.
5. Perform the diagnostic system check.
Is the repair complete?
–
System OK
–
9
1. Replace the ECM.
2. Run the engine until it reaches operating
temperature.
3. Perform the diagnostic system check.
Is the repair complete?
–
Go to Step 10
–
10
Check if any additional DTCs are set.
Are any DTCs displaced that have not been
diagnosed?
–
Go to
applicable DTC
table
System OK

1F–74 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F110
DIAGNOSTIC TROUBLE CODE (DTC) – P0118 ENGINE COOLANT
TEMPERATURE SENSOR HIGH VOLTAGE
Circuit Description
The coolant temperature sensor (ECT) uses a thermis-
tor to control the signal voltage to the engine control
module (ECM).
The ECM supplies a voltage on the signal circuit to the
sensor. When the air is cold, the resistance is high;
therefore the ECT sensor signal voltage will be high.
As the engine warms, the sensor resistance becomes
less, and the voltage drops. At normal engine operating
temperature, the voltage will be between 1.5 and 2.0
volts at the ECT sensor signal terminal.
The ECT sensor is used to the following items:

Fuel delivery.

Lock Up Clutch (LUC).

Ignition.

Evaporator Emission (EVAP) Canister Purge Valve.

Idle Air Control (IAC) valve.

Electric cooling fan.
Conditions for Setting the DTC

This DTC can be stored in “key-on” status.

The engine rum time is greater than 3 seconds.

The ECT sensor indicates that the engine coolant
temperature is less than –40°C(–40°F).

ECT voltage is greater than 4.98V.
A low voltage condition exits.
Action Taken when the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.

A history DTC is stored.

The coolant fan turns ON.

The ECM will substitutes a fixed MAP value and use
TP to control the fuel delivery (the scan tool will not
show defaulted)
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
After the engine has started, the ECT should rise steadi-
ly to about 90°C(194°F) then stabilize when the thermo-
stat opens.
Use the temperature vs. resistance values table to eval-
uate the possibility of a skewed sensor. Refer to “Te m -
perature vs. Resistance” in this Section.

ENGINE CONTROLS 1F–75
DAEWOO M-150 BL2
DTC P0118 – Engine Coolant Temperature Sensor High Voltage
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Connect the scan tool to the data link connector
(DLC).
2. Run the engine until it reaches operating
temperature.
Does the scan tool show the ECT sensor reading
within the value specified?
80~110°C
(176~230°F)
Go to
“Diagnostic
Aids”
Go to Step 3
3
1. Turn the ignition switch to LOCK.
2. Disconnect the ECT sensor connector.
3. Turn the ignition switch to ON.
Does the scan tool show the ECT sensor reading
within the value specified?
≥-30°CGo to Step 4Go to Step 6
4
1. Jumper the ECT sensor signal circuits at terminal
B and A.
2. Turn the ignition switch to ON.
Does the scan tool show the ECT sensor reading
within the value specified?
≥180°C
(356°F)
Go to Step 5Go to Step 6
5
1. Replace the ECT sensor.
2. Clear any DTCs from the ECM.
3. Perform the diagnostic system check.
Is the replacement complete?
–
System OK
–
6
Measure the voltage between ECT terminal B and
ground.
Does the voltage measure within the value
specified?
4.5–5.0VGo to Step 7Go to Step 8
7
1. Turn the ignition switch to LOCK.
2. Disconnect the ECM wiring connector.
3. Check for a faulty connector or terminals at the
ECT sensor connector terminal A and the ECM
connector terminal 45 for an open or short to
battery voltage.
Is the problem found?
–
Go to Step 8Go to Step 9
8
1. Turn the ignition switch to LOCK.
2. Repair the wire of the connector terminals as
needed.
3. Clear any DTCs from the ECM.
4. Run the engine until it reaches operating
temperature.
5. Perform the diagnostic system check.
Is the repair complete?
–
System OK
–
9
1. Replace the ECM.
2. Run the engine until it reaches operating
temperature.
3. Perform the diagnostic system check.
Is the repair complete?
–
Go to Step 10
–
10
Check if any additional DTCs are set.
Are any DTCs displaced that have not been
diagnosed?
–
Go to
applicable DTC
table
System OK

1F–90 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F130
DIAGNOSTIC TROUBLE CODE (DTC) – P0133 OXYGEN SENSOR NO ACTIVITY
Circuit Description
The engine control module (ECM) supplies a voltage of
about 450mm volts between the ECM terminals 44 and
13. The oxygen (O
2) sensor varies the voltage within a
range of about 1volt if the exhaust is rich, down to about
100mm volts if the exhaust is lean. The O
2 sensor is like
an open circuit and produces no voltage when it is below
360°C(600°F). An open O
2 sensor circuit or a cold O2
sensor causes “open loop” operation.
Conditions for Setting the DTC

The engine controls system is in closed loop.

Engine Coolant Temperature is higher than 60°C
(140°F).

The mass air flow(MAF) is between 75mg/tdc and
100mg/tdc.

The engine speed is between 3,008rpm and
3,500rpm.

The vehicle speed is between 45km/h(27.96mph)
and 55km/h(34.2mph).

The manifold air pressure is higher than 90kPa.

The ignition is at 10 volts.

The upstream O
2 sensor periods higher than 1.6 sec-
onds.

A number of glitches higher than 5 during the test.
DTCs P0107, P0108, P0112, P0113, P0117, P0118,
P0122, P0123, P0131, P0132, P0131, P0132,
P0137, P0138, P1671, P0300, P0335, P0336,
P0341, P0400, P0404, P0405, P0444, P0445 are
NOT SET.
Action Taken when the DTC Sets

Emission related.

“Armed” after two trip with a fail.

“Disarmed” after one trip with a pass.

MIL on if failure is detected in three consecutive trips.

Stores a History DTC on the third consecutive with a
fail (The DTC will be armed after the second fail).

Stores a Freeze Frame on the third consecutive trip
with a fail (if empty).
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Normal scan tool voltage varies between 0.15 to 8.5mV
while in Closed Loop. If DTC P0133 is intermittent, refer
to “Intermittent” in this Section.

1F–100 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F140
DIAGNOSTIC TROUBLE CODE (DTC) – P0140 HEATED OXYGEN SENSOR NO
ACTIVITY
Circuit Description
The engine control module (ECM) supplies a voltage of
about 450mm volts between the ECM terminals 64 and
13. The oxygen (O
2) sensor varies the voltage within a
range of about 1volt if the exhaust is rich, down to about
100mm volts if the exhaust is lean. The O
2 sensor is like
an open circuit and produces no voltage when it is below
360°C(600°F). An open O
2 sensor circuit or a cold O2
sensor causes “open loop” operation.
Conditions for Setting the DTC

The engine controls system is in closed loop.

Engine Coolant Temperature is higher than 70°C
(140°F).

The mass air flow(MAF) is between 25kg/h and
50kg/h.

The engine speed is between 2,400rpm and 300rpm.

The vehicle speed is between 64km/h(12.4mph) and
80km/h(24.9mph).

The manifold air pressure is higher than 70kPa.

The ignition is at 10 volts.

No transition from rich side to lean side or lean side to
rich side during 7.8 seconds even with a forcing of O
2
sensor controller.

DTCs P0107, P0108, P0112, P0113, P0117, P0118,
P0122, P0123, P0137, P0138, P0137, P0138,P0137, P0138, P1671, P0300, P0335, P0336,
P0341, P0400, P0404, P0405, P0644, P0645 are
NOT SET.
Action Taken when the DTC Sets

Emission related.

“Armed” after two trip with a fail.

“Disarmed” after one trip with a pass.

MIL on if failure is detected in three consecutive trips.

Stores a History DTC on the third consecutive with a
fail (The DTC will be armed after the second fail).

Stores a Freeze Frame on the third consecutive trip
with a fail (if empty).
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.

Disconnecting the ECM battery feed for 10 seconds.
Diagnostic Aids

Normal scan tool voltage varies between 0.15 to
8.5mV while in Closed Loop. If DTC P0140 is inter-
mittent, refer to “Intermittent” in this Section.

1F–106 ENGINE CONTROLS
DAEWOO M-150 BL2
DIAGNOSTIC TROUBLE CODE (DTC) – P0171 FUEL TRIM SYSTEM TOO LEAN
System Description
To provide the best possible combination of driveability,
fuel economy, and emission control, a Closed Loop air/
fuel metering system is used. While in Closed Loop, the
Engine Control Module (ECM) monitors the oxygen sen-
sor (O2S) signal voltage and adjusts fuel delivery based
on signal voltage. A change made to fuel delivery will be
indicated by the long and short term fuel trim values
which can be monitored with the scan tool. Ideal fuel trim
values are around 128 (0%). If the O2S signal is indicat-
ing a lean condition, the ECM will add fuel resulting in
fuel trim values above 128 (0% to 100%). If a rich condi-
tion is detected, the fuel trim values will be below 128
(0% to –100%), indicating that the ECM is reducing the
amount of fuel delivered. If exhaust emissions reach an
excessive level due to a lean or rich condition, a fuel trim
Diagnostic Trouble Code (DTC) is set.
Conditions for Setting the DTC

No intrusive tests active.

DTCs P0106, P0107, P0108, P0112, P0113, P0117,
P0118, P0122, P0123, P0125, P0131, P0132,
P0133, P0134, P0137, P0138, P0140, P0141,
P1167, P1171, P0201, P0202, P0203, P0204,
P0300, P0336, P0337, P0341, P0342, P0402,
P0404, P1404, P0405, P0406, P0443, P0506, and
P0507are not set.

The average of short term fuel trim value is greater
than or equal to 120.

Throttle Position (TP) is less than 95%.

Engine speed is between 700 and 6000 rpm.

Barometric Pressure (BARO) is greater than 92.0
kPa (10.4 psi).

Coolant temperature is between 80°C (176°F) and
11 5°C (239°F).

Manifold Absolute Pressure (MAP) is more than 90
kPa (10.2 psi).

System is in closed loop.

Adaptive index is ready.
Action Taken when the DTC Sets

Emission related.

“Armed” after two trip with a fail.

“Disarmed” after one trip with a pass.

MIL on if failure is detected in three consecutive trips.

Stores a History DTC on the third consecutive with a
fail (The DTC will be armed after the second fail).
Stores a Freeze Frame on the third consecutive trip
with a fail (if empty).
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Important: After repairs, use the scan tool Fuel Trim
Reset function to reset the long-term fuel trim to 128
(0%).

Fuel pressure – The system will be lean if the pres-
sure is too low. It may be necessary to monitor fuel
pressure while driving the vehicle at various road
speeds and/or loads to confirm.

Map sensor – An output that causes the ECM to
sense a lower than normal manifold pressure (high
vacuum) can cause the system to go lean. Discon-
necting the MAP sensor will allow the ECM to substi-
tute a fixed (default) value for the MAP sensor. If the
lean condition is gone when the sensor is discon-
nected, substitute a known good sensor and recheck.

Fuel contamination – Water, in even small amounts,
near the in-tank fuel pump inlet can be delivered to
the injector. The water causes a lean exhaust and
can set DTC P0171.
Check for poor O2S or MAP sensor connection at the
ECM. Inspect the harness connectors for the following
conditions:

Backed-out terminals

Improper mating

Broken locks

Improperly formed

Damaged terminals

Poor terminal-to-wire connection
Inspect the wiring harness for damage. If the harness
appears to be OK, observe the O2S display on the scan
tool while moving the connectors and the wiring harness
related to the engine harness. A change in the display
will indicate the location of the fault.
Check the brake power booster check valve for possible
leaks.