2003 DAEWOO MATIZ windshield wipers

9D –8 WIPERS/WASHER SYSTEMS
DAEWOO M-150 BL2
D109D526
Installation Procedure
1. Install the wiper motor to the engine room with the
bolts.
a. Wiper motor assembly bolt.
2. Connect the electrical connector.
D109D527
3. Install the wiper linkage to the wiper motor linkage
ball.
b. Wiper linkage ball.
D109D528
4. Install the cowl vent grille. Refer to Section 9R, Body
Front End.
5. Install the windshield wiper arm. Refer to “Windshield
Wiper Arm” in this section.
6. Connect the negative battery cable.
D19D529A
REAR WINDOW WIPER MOTOR
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the wiper arm from the tailgate. Refer to
“Windshield Wiper Arm” in this section.
3. Remove the tailgate inside trim. Refer to Section 9G,
Interior Trim.
4. Remove the rear wiper motor assembly.

Disconnect the electrical connector (1).

Remove the screws (2).

Remove the rear wiper motor assembly (3).

WIPERS/WASHER SYSTEMS 9D–9
DAEWOO M-150 BL2
D19D530A
Caution: Because the wiper motor link plate is
fixed, do not separate the wiper motor from the
bracket.
D19D531A
Installation Procedure
1. Install the wiper motor assembly to the tailgate with
the screws.
2. Connect the electrical connector.
3. Install the tailgate inside trim. Refer to Section 9G, In-
terior Trim.
4. Install the wiper arm. Refer to “Windshield Wiper
Arm” in this section.
5. Connect the negative battery cable.
D109D523
WINDSHIELD WIPER LINKAGE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the windshield wiper arms. Refer to ”Wind-
shield Wiper Arm” in this section.
2. Remove the cowl vent grille. Refer to Section 9R,
Body Front End.
3. Separate the wiper linkage from the wiper motor.

Separate the wiper linkage from the wiper motor
linkage ball (1).
D109D532
4. Remove the wiper linkage.

Remove the wiper linkage nuts (1).

Remove the wiper linkage (2).

9D –10 WIPERS/WASHER SYSTEMS
DAEWOO M-150 BL2
D19D533A
1.5–2.0 Nm
Installation Procedure
1. Install the wiper linkage with the wiper linkage nuts.
Tighten
Tighten the wiper linkage nuts to 1.5–2.0 Nm (13–18
lb-in).
a. Wiper linkage nut.
2. Install the wiper motor linkage ball.
3. Install the cowl vent grille. Refer to Section 9R, Body
Front End.
4. Install the windshield wiper arms. Refer to ”Wind-
shield Wiper Arm” in this section.
D109D534
WINDSHIELD WIPER BLADE
Removal Procedure
1. Pull the wiper blade off the arm by pushing the wiper
blade retaining clip (1).
D109D535
Installation Procedure
1. Install the wiper blade to the arm.
D109D536
WASHER RESERVOIR
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the washer reservoir inlet.

Remove the bolt (1).

Remove the washer reservoir inlet (2).

9D –12 WIPERS/WASHER SYSTEMS
DAEWOO M-150 BL2
D109D539
Installation Procedure
1. Install the wiper motor to the washer reservoir assem-
bly.
2. Install the washer reservoir assembly.
Refer to “Washer Reservoir” in this section.
3. Connect the negative battery cable.
4. Fill the washer reservoir.
D109D541
WINDSHIELD WASHER NOZZLE
Removal Procedure
1. Remove the cowl vent grille. Refer to Section 9R,
Body Front End.
2. Remove the washer nozzle from the cowl vent grille.

Disconnect the washer nozzle hose (1).

Remove the washer nozzle (2).
D109D542
Installation Procedure
1. Install the washer nozzle to the cowl vent grille.
2. Install the washer nozzle hose to the washer nozzle.
3. Install the cowl vent grille. Refer toSec-
tion 9R, Body Front End.
D109D543
REAR WINDOW WASHER NOZZLE
Removal Procedure
1. Remove the washer nozzle from the wiper arm.

Disconnect the washer nozzle hose (1).

Remove the washer nozzle (2).

9D –16 WIPERS/WASHER SYSTEMS
DAEWOO M-150 BL2
SCHEMATIC AND ROUTING DIAGRAMS
WINDSHIELD/REAR WINDOW WIPER AND WASHER SYSTEM
D19D208B