2003 CHRYSLER VOYAGER diagram

(IPM) cover for rear blower motor relay identification
and location.
(2) Position the rear blower motor relay to the
proper receptacle in the IPM.
(3) Align the rear blower motor relay terminals
with the terminal cavities in the IPM relay recepta-
cle.
(4) Push down firmly on the rear blower motor
relay until the terminals are fully seated in the ter-
minal cavities in the IPM receptacle.
(5) Install and latch the cover onto the IPM.
(6) Reconnect the battery negative cable.
BLOWER MOTOR RESISTOR
DESCRIPTION
A blower motor resistor is used on this model when
it is equipped with the manual heater-A/C control
(Fig. 8). Models equipped with the optional Auto-
matic Temperature Control (ATC) use a blower powermodule, instead of the blower motor resistor. The
blower motor resistor is installed in a mounting hole
on the back of the rear heater-A/C unit housing,
directly above the expansion valve. The resistor con-
sists of a molded plastic mounting plate with an inte-
gral connector receptacle. Concealed behind the
mounting plate within the rear heater-A/C unit hous-
ing is an electrical circuit board.. The resistor mount-
ing plate is secured with two screws to the rear
heater-A/C unit housing and is accessed for service
by removing the right quarter and D-pillar trim pan-
els.
The blower motor resistor cannot be adjusted or
repaired and, if faulty or damaged, it must be
replaced.
OPERATION
The blower motor resistor is connected to the vehi-
cle electrical system through a dedicated take out
and connector of the rear HVAC wire harness. The
blower motor resistor has an electrical circuit board
which will reduce the current flow through the
blower motor to change the blower motor speed. The
blower motor switch in the manual heater-A/C con-
trol directs the ground path for the blower motor
through the correct resistor wire to obtain the
selected speed. With the blower motor switch in the
lowest speed position, the ground path for the motor
is applied through both resistor wires. Each higher
speed selected with the blower motor switch applies
the blower motor ground path through fewer of the
resistor wires, increasing the blower motor speed.
When the blower motor switch is in the highest
speed position, the blower motor resistor wires are
bypassed and the blower motor receives a direct path
to ground through the blower motor switch. The
blower motor resistor may be diagnosed using con-
ventional diagnostic tools and methods.
DIAGNOSIS AND TESTING - BLOWER MOTOR
RESISTOR
Refer to the appropriate wiring information. The
wiring information includes wiring diagrams, proper
wire and connector repair procedures, details of wire
harness routing and retention, connector pin-out
information and location views for the various wire
harness connectors, splices and grounds.
(1) Disconnect and isolate the battery negative
cable.
(2) Disconnect the rear HVAC wire harness con-
nector for the blower motor resistor from the resistor
connector receptacle.
(3) Check for continuity between each of the
blower motor switch input terminals of the blower
motor resistor and the resistor output terminal. In
each case there should be continuity. If OK, repair
Fig. 8 Blower Motor Resistor
1 - REAR HEATER-A/C UNIT HOUSING
2 - D-PILLAR
3 - BLOWER PIGTAIL WIRE
4 - CONNECTOR
5 - EXPANSION VALVE
6 - SCREW (2)
7 - BLOWER MOTOR RESISTOR
24 - 34 CONTROLS - REARRS
BLOWER MOTOR RELAY (Continued)
ProCarManuals.com

CUSHION SIDE COVER - INSTALLATION,
FRONT SEAT........................23-93
CUSHION SIDE COVER - REMOVAL,
FRONT SEAT........................23-93
CV BOOT - INNER - INSTALLATION........3-6
CV BOOT - INNER - REMOVAL............3-6
CV BOOT - INNER/OUTER -
INSTALLATION........................3-17
CV BOOT - INNER/OUTER - REMOVAL.....3-15
CV BOOT - OUTER - INSTALLATION.......3-10
CV BOOT - OUTER - REMOVAL...........3-10
CYCLE - STANDARD PROCEDURE,
POWER DOOR LEARN................8N-28
CYCLE - STANDARD PROCEDURE,
POWER LIFTGATE LEARN...............8N-9
CYLINDER - DESCRIPTION, KEY/LOCK....19-20
CYLINDER - DESCRIPTION, STANDARD 4 . . . 8I-9
CYLINDER - INSTALLATION, KEY/LOCK . . . 19-20
CYLINDER - INSTALLATION, LOCK . . 23-20,23-41
CYLINDER - INSTALLATION, SLAVE.......6-11
CYLINDER - INSTALLATION, SUPPORT....23-42
CYLINDER - LHD - INSTALLATION,
MASTER............................6-10
CYLINDER - LHD - REMOVAL, MASTER.....6-9
CYLINDER - OPERATION, KEY/LOCK......19-20
CYLINDER - REMOVAL, KEY/LOCK.......19-20
CYLINDER - REMOVAL, LOCK......23-19,23-41
CYLINDER - REMOVAL, SLAVE...........6-11
CYLINDER - REMOVAL, SUPPORT.......23-42
CYLINDER - RHD - INSTALLATION,
MASTER.............................6-9
CYLINDER - RHD - REMOVAL, MASTER.....6-8
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER.................5-35
CYLINDER BORE FITTING - STANDARD
PROCEDURE, PISTON TO...............9-42
CYLINDER BORE HONING - STANDARD
PROCEDURE....................9-112,9-35
CYLINDER COMBUSTION PRESSURE
LEAKAGE TEST - DIAGNOSIS AND
TESTING.........................9-83,9-9
CYLINDER COMPRESSION PRESSURE
TEST - DIAGNOSIS AND TESTING.....9-83,9-9
CYLINDER (FLUID RESERVOIR) -
ASSEMBLY, MASTER...................5-38
CYLINDER (FLUID RESERVOIR) -
DISASSEMBLY, MASTER................5-37
CYLINDER HEAD - CLEANING.......9-100,9-26
CYLINDER HEAD - DESCRIPTION.....9-24,9-99
CYLINDER HEAD - INSPECTION.....9-101,9-26
CYLINDER HEAD - INSTALLATION . . . 9-101,9-26
CYLINDER HEAD - REMOVAL.......9-100,9-25
CYLINDER HEAD COVER - CLEANING......9-31
CYLINDER HEAD COVER - INSPECTION....9-31
CYLINDER HEAD COVER -
INSTALLATION........................9-31
CYLINDER HEAD COVER - LEFT -
INSTALLATION.......................9-103
CYLINDER HEAD COVER - LEFT -
REMOVAL..........................9-103
CYLINDER HEAD COVER - REMOVAL......9-31
CYLINDER HEAD COVER - RIGHT -
INSTALLATION.......................9-103
CYLINDER HEAD COVER - RIGHT -
REMOVAL..........................9-102
CYLINDER HEAD COVER(S) -
DESCRIPTION.......................9-102
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING....................9-24,9-99
CYLINDER HEAD OFF - INSTALLATION . . . 9-108,
9-33
CYLINDER HEAD OFF - REMOVAL . . . 9-106,9-32
CYLINDER HEAD ON - INSTALLATION....9-108,
9-33
CYLINDER HEAD ON - REMOVAL....9-106,9-32
CYLINDER HOUSING - INSTALLATION,
LOCK..............................19-19
CYLINDER HOUSING - REMOVAL, LOCK . . 19-17
CYLINDER LOCK SWITCH -
DESCRIPTION, DOOR
.................8N-40
CYLINDER LOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR
.................8N-40
CYLINDER LOCK SWITCH -
INSTALLATION, DOOR
.................8N-41
CYLINDER LOCK SWITCH - OPERATION,
DOOR
.............................8N-40
CYLINDER LOCK SWITCH - REMOVAL,
DOOR
.............................8N-41CYLINDERS - INSPECTION, WHEEL.......5-57
CYLINDERS - INSTALLATION, WHEEL.....5-57
CYLINDERS - REMOVAL, WHEEL.........5-57
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR OF . . 9-10,9-86
DAMPER - INSTALLATION, VIBRATION . . . 9-130,
9-47
DAMPER - REMOVAL, VIBRATION . . . 9-130,9-47
DATA BUS COMMUNICATION RECEIVE -
PCM INPUT - OPERATION..............8E-15
DATA LINK CONNECTOR - DESCRIPTION . . . 8E-6
DATA LINK CONNECTOR - OPERATION.....8E-7
DAY / NIGHT MIRROR - DESCRIPTION,
AUTOMATIC........................8N-47
DAY / NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC................8N-47
DAY / NIGHT MIRROR - OPERATION,
AUTOMATIC........................8N-47
DCHA - DIAGNOSIS AND TESTING,
DIESEL SUPPLEMENTAL HEATER.......24-107
DCHA - EXPORT - DESCRIPTION, DIESEL
SUPPLEMENTAL HEATER.............24-106
DEAERATION - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-4
DECOUPLER PULLEY - DESCRIPTION,
GENERATOR........................8F-25
DECOUPLER PULLEY - DIAGNOSIS AND
TESTING, GENERATOR................8F-25
DECOUPLER PULLEY - INSTALLATION,
GENERATOR........................8F-26
DECOUPLER PULLEY - OPERATION,
GENERATOR..........................8F-25
DECOUPLER PULLEY - REMOVAL,
GENERATOR........................8F-26
DEFINITION - DESCRIPTION, TRIP........25-1
DEFLECTOR - INSTALLATION, WIND.....23-118
DEFLECTOR - REMOVAL, WIND........23-118
DEFOGGER RELAY - DESCRIPTION.......8G-2
DEFOGGER SWITCH - DESCRIPTION,
REAR WINDOW.......................8G-2
DEFOGGER SWITCH - OPERATION, REAR
WINDOW............................8G-2
DEFROSTER DUCT - INSTALLATION......24-48
DEFROSTER DUCT - REMOVAL..........24-47
DEMAGNETIZING - STANDARD
PROCEDURE, COMPASS...............8M-4
DEMISTER DUCTS - INSTALLATION......24-48
DEMISTER DUCTS - REMOVAL..........24-48
DEMISTER OUTLET - INSTALLATION.....24-42
DEMISTER OUTLET - REMOVAL.........24-41
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN
AIRBAG.............................8O-3
DETECTION ASSY - INSTALLATION,
NATURAL VAC LEAK..................25-13
DETECTION ASSY - REMOVAL, NATURAL
VAC LEAK..........................25-13
DETECTION PUMP - INSTALLATION,
LEAK..............................25-13
DETECTION PUMP - REMOVAL, LEAK....25-13
DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE........................8W-01-8
DIAGNOSTIC SYSTEM - DIAGNOSIS AND
TESTING, ON-BOARD.................8F-21
DIAGNOSTIC TROUBLE CODES -
STANDARD PROCEDURE, OBTAINING.....8E-15
DIAGRAMS - 41TE TRANSAXLE
HYDRAULIC SCHEMATICS,
SCHEMATICS.......................21-169
DIAGRAMS - DESCRIPTION, HOW TO
USE WIRING......................8W-01-1
DIESEL - DESCRIPTION, 2.5L...........19-51
DIESEL - INSTALLATION, 2.5L..........19-52
DIESEL - REMOVAL, 2.5L..............19-51
DIESEL ENGINE - DESCRIPTION, FUEL
REQUIREMENTS.......................0-6
DIESEL ENGINES - DESCRIPTION,
ENGINE OIL...........................0-6
DIESEL HEATER WIRING -
INSTALLATION, SUPPLEMENTAL
........24-112
DIESEL HEATER WIRING - REMOVAL,
SUPPLEMENTAL
....................24-112
DIESEL SUPPLEMENTAL HEATER - DCHA
- DIAGNOSIS AND TESTING
...........24-107
DIESEL SUPPLEMENTAL HEATER - DCHA
- EXPORT - DESCRIPTION
............24-106
DIFFERENTIAL - ASSEMBLY
............21-66DIFFERENTIAL - DESCRIPTION..........21-62
DIFFERENTIAL - DISASSEMBLY.........21-62
DIFFERENTIAL - OPERATION............21-62
DIFFERENTIAL ASSEMBLY -
DESCRIPTION........................3-39
DIFFERENTIAL ASSEMBLY - OPERATION . . . 3-39
DIFFERENTIAL ASSEMBLY FLUID
CHANGE - STANDARD PROCEDURE.......3-40
DIFFERENTIAL BEARING PRELOAD -
ADJUSTMENT......................21-199
DIFFERENTIAL CARRIER SEAL -
INSTALLATION........................21-9
DIFFERENTIAL CARRIER SEAL -
REMOVAL...........................21-9
DIFFERENTIAL SIDE GEAR END PLAY -
ADJUSTMENT.......................21-70
DIFFERENTIAL TURNING TORQUE -
ADJUSTMENT.......................21-69
DIMENSIONS - SPECIFICATIONS, BODY
OPENING..........................23-124
DIMENSIONS, SPECIFICATIONS - FRAME . . . 13-4
DIODE - INSTALLATION............8W-01-14
DIODE - REMOVAL................8W-01-14
DISC AND PRESSURE PLATE - 2.5L TD -
INSTALLATION, CLUTCH................6-12
DISC AND PRESSURE PLATE - 2.5L TD -
REMOVAL, CLUTCH....................6-11
DISC BRAKE CALIPER - INSTALLATION,
REAR...............................5-30
DISC BRAKE CALIPER - REMOVAL,
REAR...............................5-27
DISC BRAKE CALIPER ADAPTER -
INSTALLATION, FRONT.................5-31
DISC BRAKE CALIPER ADAPTER -
REMOVAL, FRONT.....................5-31
DISC BRAKE CALIPER (DISC/DISC
BRAKES) - INSTALLATION, FRONT........5-27
DISC BRAKE CALIPER (DISC/DISC
BRAKES) - REMOVAL, FRONT............5-24
DISC BRAKE CALIPER (DISC/DRUM
BRAKES) - INSTALLATION, FRONT........5-27
DISC BRAKE CALIPER (DISC/DRUM
BRAKES) - REMOVAL, FRONT............5-24
DISC BRAKE CALIPER GUIDE PINS
(DISC/DRUM BRAKES) -
INSTALLATION........................5-31
DISC BRAKE CALIPER GUIDE PINS
(DISC/DRUM BRAKES) - REMOVAL.......5-31
DISC BRAKE SHOES - CLEANING.....5-16,5-18
DISC BRAKE SHOES - INSPECTION . . . 5-16,5-18
DISC BRAKE SHOES - INSTALLATION,
REAR...............................5-19
DISC BRAKE SHOES - REMOVAL, REAR....5-17
DISC BRAKE SHOES (DISC/DISC
BRAKES) - INSTALLATION, FRONT........5-16
DISC BRAKE SHOES (DISC/DISC
BRAKES) - REMOVAL, FRONT............5-14
DISC BRAKE SHOES (DISC/DRUM
BRAKES) - INSTALLATION, FRONT........5-17
DISC BRAKE SHOES (DISC/DRUM
BRAKES) - REMOVAL, FRONT............5-15
DISC BRAKES (EXPORT) - DESCRIPTION . . . 5-13
DISC BRAKES (FRONT) - DESCRIPTION....5-11
DISC BRAKES (FRONT) - OPERATION......5-13
DISC BRAKES (REAR) - DESCRIPTION.....5-12
DISC BRAKES (REAR) - OPERATION......5-13
DISC RUNOUT - DIAGNOSIS AND
TESTING, CLUTCH COVER...............6-6
DISCHARGE (ESD) SENSITIVE DEVICES -
STANDARD PROCEDURE,
ELECTROSTATIC...................8W-01-8
DISCHARGE LINE - INSTALLATION.......24-69
DISCHARGE LINE - REMOVAL..........24-68
DISPLAY TEST MODE, OPERATION - DRB
IIITSTATE ...........................25-9
DISTRIBUTION DUCT - INSTALLATION,
A/C................................24-53
DISTRIBUTION DUCT - INSTALLATION,
REAR HEATER.......................24-59
DISTRIBUTION DUCT - REMOVAL, A/C
....24-53
DISTRIBUTION DUCT - REMOVAL, REAR
HEATER
............................24-59
DISTRIBUTION DUCTS - INSTALLATION,
FLOOR
.............................24-49
DISTRIBUTION DUCTS - REMOVAL,
FLOOR
.............................24-48
DISTRIBUTION SYSTEM - DESCRIPTION,
POWER
..........................8W-97-1
RSINDEX9
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

HINGE - INSTALLATION, LOWER........23-28
HINGE - INSTALLATION, UPPER.........23-35
HINGE - REMOVAL.........23-18,23-39,23-59
HINGE - REMOVAL, BENCH SEAT BACK . . 23-100
HINGE - REMOVAL, CENTER............23-24
HINGE - REMOVAL, LOWER............23-28
HINGE - REMOVAL, UPPER.............23-35
HINGE COVERS - QUAD BUCKET, 50/50
SPLIT, BENCH - INSTALLATION, SEAT
BACK.............................23-100
HINGE COVERS - QUAD BUCKET, 50/50
SPLIT, BENCH - REMOVAL, SEAT BACK . . 23-100
HOISTING - STANDARD PROCEDURE......0-15
HOLD OPEN LATCH - INSTALLATION.....23-25
HOLD OPEN LATCH - REMOVAL.........23-25
HOLD OPEN LATCH CABLE -
INSTALLATION.......................23-38
HOLD OPEN LATCH CABLE - REMOVAL . . . 23-37
HOLD OPEN LATCH STRIKER -
INSTALLATION.......................23-26
HOLD OPEN LATCH STRIKER -
REMOVAL..........................23-26
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-15
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-16
HOLDDOWN - OPERATION, BATTERY.....8F-15
HOLDDOWN - REMOVAL, BATTERY......8F-16
HOLDER - INSTALLATION, CUP.........23-63
HOLDER - INSTALLATION, QUAD
BUCKET SEAT SIDE SHIELD - NO CUP.....23-96
HOLDER - INSTALLATION, QUAD
BUCKET SEAT SIDE SHIELD/CUP........23-95
HOLDER - REMOVAL, CUP.............23-63
HOLDER - REMOVAL, QUAD BUCKET
SEAT SIDE SHIELD - NO CUP...........23-96
HOLDER - REMOVAL, QUAD BUCKET
SEAT SIDE SHIELD/CUP...............23-95
HOLDING CLUTCHES - DESCRIPTION....21-207
HOLDING CLUTCHES - OPERATION.....21-207
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-5
HONING - STANDARD PROCEDURE,
CYLINDER BORE.................9-112,9-35
HOOD - INSTALLATION................23-60
HOOD - REMOVAL....................23-59
HOOD AJAR SWITCH - EXPORT -
INSTALLATION.......................8Q-3
HOOD AJAR SWITCH - EXPORT -
REMOVAL...........................8Q-3
HORN - DIAGNOSIS AND TESTING.......8H-3
HORN - INSTALLATION.................8H-5
HORN - REMOVAL....................8H-5
HORN CHIRP PREFERENCE - STANDARD
PROCEDURE........................8N-42
HORN RELAY - DIAGNOSIS AND
TESTING............................8H-5
HORN RELAY - INSTALLATION...........8H-5
HORN RELAY - REMOVAL..............8H-5
HORN SWITCH - DESCRIPTION..........8H-5
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - EXPORT - INSTALLATION,
HEADLAMP WASHER.................8R-12
HOSE - EXPORT - REMOVAL, HEADLAMP
WASHER...........................8R-12
HOSE - INSTALLATION, HEATER . . . 24-101,24-80
HOSE - REMOVAL, HEATER......24-100,24-78
HOSE CLAMPS - DESCRIPTION...........7-1
HOSE CLAMPS - OPERATION.............7-2
HOSES - DESCRIPTION, BRAKE TUBES
....5-14
HOSES - INSPECTION, BRAKE TUBES
.....5-14
HOSES - INSTALLATION, WASHER
.......8R-16
HOSES - OPERATION, BRAKE TUBES
......5-14
HOSES - REMOVAL, WASHER
..........8R-16
HOSES AND CLAMP - STANDARD
PROCEDURE
.........................14-6
HOUSING - INSTALLATION, AIR
CLEANER
........................9-24,9-99
HOUSING - INSTALLATION, HVAC
........24-50
HOUSING - INSTALLATION, LOCK
CYLINDER
..........................19-19
HOUSING - INSTALLATION, REAR
HEATER-A/C
.........................24-58
HOUSING - REMOVAL, AIR CLEANER
. . 9-24,9-99
HOUSING - REMOVAL, HVAC
...........24-49
HOUSING - REMOVAL, LOCK CYLINDER
. . 19-17HOUSING - REMOVAL, REAR HEATER-A/
C .................................24-56
HOUSING FLUID CHANGE - STANDARD
PROCEDURE, OVERRUNNING CLUTCH.....3-41
HOUSING FLUID LEAKAGE - DIAGNOSIS
AND TESTING, TORQUE CONVERTER....21-123
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
HUB / BEARING - DESCRIPTION.......2-30,2-5
HUB / BEARING - INSTALLATION......2-32,2-5
HUB / BEARING - OPERATION........2-30,2-5
HUB / BEARING - REMOVAL..........2-31,2-5
HUB AND BEARING - DIAGNOSIS AND
TESTING.........................2-30,2-5
HVAC - LWB - INSTALLATION, SEAT
BELT & RETRACTOR - SECOND ROW -
RIGHT OUTBOARD WITH REAR.........8O-15
HVAC - LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR...............8O-15
HVAC HOUSING - INSTALLATION........24-50
HVAC HOUSING - REMOVAL............24-49
HVAC LOUVER - INSTALLATION, REAR . . . 23-79
HVAC LOUVER - REMOVAL, REAR.......23-79
HYDRAULIC CIRCUITS AND VALVES -
OPERATION..........................5-83
HYDRAULIC LASH ADJUSTER NOISE
DIAGNOSIS - DIAGNOSIS AND
TESTING............................9-34
HYDRAULIC LASH ADJUSTERS -
INSTALLATION........................9-34
HYDRAULIC LASH ADJUSTERS -
REMOVAL...........................9-34
HYDRAULIC LIFTERS - DIAGNOSIS AND
TESTING...........................9-113
HYDRAULIC LIFTERS (CAM IN BLOCK) -
DESCRIPTION.......................9-113
HYDRAULIC LIFTERS (CAM IN BLOCK) -
INSTALLATION.......................9-114
HYDRAULIC LIFTERS (CAM IN BLOCK) -
REMOVAL..........................9-114
HYDRAULIC PRESSURE TESTS -
DIAGNOSIS AND TESTING............21-120
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS - 41TE TRANSAXLE....21-169
HYDROSTATIC LOCKED ENGINE -
STANDARD PROCEDURE............9-10,9-85
ICU - ASSEMBLY......................5-94
ICU - DISASSEMBLY...................5-93
ICU (INTEGRATED CONTROL UNIT) -
DESCRIPTION........................5-89
ICU (INTEGRATED CONTROL UNIT) -
OPERATION..........................5-90
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-2
IDENTIFICATION - DESCRIPTION,
VEHICLE............................23-1
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION, DIAGNOSIS AND
TESTING - SEAL......................21-3
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-9
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-28
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-29
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-28
IDLE AIR CONTROL MOTOR - REMOVAL
. . 14-29
IGNITION COIL - DESCRIPTION
...........8I-6
IGNITION COIL - OPERATION
.............8I-6
IGNITION INTERLOCK - DESCRIPTION
....19-17
IGNITION SENSE - PCM INPUT -
OPERATION
.........................8E-15
IGNITION SWITCH - INSTALLATION
......19-16
IGNITION SWITCH - REMOVAL
..........19-14
IGNITION SYSTEM - DESCRIPTION
........8I-1
IGNITION SYSTEM - OPERATION
..........8I-1
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE
........................8F-13
IIITSTATE DISPLAY TEST MODE,
OPERATION - DRB
....................25-9
ILLUMINATION LAMPS - INSTALLATION,
CLUSTER
...........................8L-26
ILLUMINATION LAMPS - REMOVAL,
CLUSTER
...........................8L-26IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY........................8E-18
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY........................8E-19
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY........................8E-18
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY........................8E-18
IMMOBILIZER SYSTEM - DIAGNOSIS
AND TESTING, SENTRY KEY.............8Q-3
IMPACT AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE..................8O-17
IMPACT AIRBAG CONTROL MODULE -
INSTALLATION, SIDE.................8O-17
IMPACT AIRBAG CONTROL MODULE -
OPERATION, SIDE....................8O-17
IMPACT AIRBAG CONTROL MODULE -
REMOVAL, SIDE.....................8O-17
INBOARD - 50/50 BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW.......................8O-12
INBOARD - 50/50 BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-12
INBOARD - INSTALLATION, SEAT BELT
BUCKLE - FRONT....................8O-11
INBOARD - QUAD BUCKET -
INSTALLATION, SEAT BELT BUCKLE -
FIRST ROW.........................8O-11
INBOARD - QUAD BUCKET - REMOVAL,
SEAT BELT BUCKLE - FIRST ROW.......8O-11
INBOARD - REMOVAL, SEAT BELT
BUCKLE - FRONT....................8O-11
INDICATOR LAMP - DESCRIPTION,
VTSS/SKIS..........................8Q-5
INDICATOR LAMP - OPERATION,
VTSS/SKIS..........................8Q-5
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR...............22-16
INFLATION PRESSURES - STANDARD
PROCEDURE, TIRE...................22-16
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-6
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE.................8M-9
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE............................8M-9
INFRARED TEMPERATURE SENSOR -
DESCRIPTION..................24-23,24-35
INFRARED TEMPERATURE SENSOR -
OPERATION....................24-24,24-35
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-37
INJECTION SYSTEM - OPERATION.......14-18
INJECTOR - DESCRIPTION, FUEL........14-26
INJECTOR - OPERATION, FUEL..........14-26
INLET AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-29
INLET AIR TEMPERATURE SENSOR -
OPERATION.........................14-29
INLET FILTER - INSTALLATION..........14-13
INLET FILTER - REMOVAL..............14-13
INLET TUBE - 2.4L - DESCRIPTION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - INSTALLATION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - REMOVAL, WATER
PUMP..............................7-35
INLET TUBE - 3.3/3.8L - INSTALLATION,
WATER PUMP........................7-36
INLET TUBE - 3.3/3.8L - REMOVAL,
WATER PUMP........................7-36
INNER - INSTALLATION, CV BOOT.........3-6
INNER - REMOVAL, CV BOOT.............3-6
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-112
INNER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-112
INNER SEAL - INSTALLATION, HALF
SHAFT.............................21-12
INNER SEAL - REMOVAL, HALF SHAFT
. . . 21-12
INNER/OUTER - INSTALLATION, CV
BOOT
...............................3-17
INNER/OUTER - REMOVAL, CV BOOT
......3-15
INPUT - DESCRIPTION, SPEED SENSOR
. 21-239
INPUT - INSTALLATION, SPEED SENSOR
. 21-240
16 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

RETRACTOR - SECOND ROW - LEFT
OUTBOARD - REMOVAL, SEAT BELT.....8O-16
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD - INSTALLATION, SEAT
BELT ..............................8O-14
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD - REMOVAL, SEAT BELT.....8O-14
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT.............8O-15
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC - LWB -
REMOVAL, SEAT BELT................8O-15
RETRAIN - STANDARD PROCEDURE,
TIRE PRESSURE SENSOR..............22-10
RETURN - PCM INPUT - OPERATION,
SENSOR............................8E-15
RHD - DESCRIPTION...................5-35
RHD - INSTALLATION..........5-39,5-47,5-95
RHD - INSTALLATION, MASTER
CYLINDER............................6-9
RHD - INSTALLATION, PEDAL TORQUE
SHAFT..............................5-39
RHD - REMOVAL..............5-37,5-43,5-91
RHD - REMOVAL, MASTER CYLINDER......6-8
RHD - REMOVAL, PEDAL TORQUE
SHAFT..............................5-39
RHD GEAR - INSTALLATION............19-33
RHD GEAR - REMOVAL................19-31
RIGHT - CLEANING, EXHAUST
MANIFOLD..........................9-151
RIGHT - INSPECTION, EXHAUST
MANIFOLD...........................9-151
RIGHT - INSTALLATION, CYLINDER
HEAD COVER........................9-103
RIGHT - INSTALLATION, EXHAUST
MANIFOLD..........................9-151
RIGHT - REMOVAL, CYLINDER HEAD
COVER.............................9-102
RIGHT - REMOVAL, EXHAUST MANIFOLD . 9-150
RIGHT B-PILLAR SWITCH -
DESCRIPTION.......................8N-32
RIGHT B-PILLAR SWITCH -
INSTALLATION......................8N-32
RIGHT B-PILLAR SWITCH - OPERATION . . 8N-32
RIGHT B-PILLAR SWITCH - REMOVAL....8N-32
RIGHT D-PILLAR TRIM PANEL -
INSTALLATION.......................23-80
RIGHT D-PILLAR TRIM PANEL -
REMOVAL..........................23-80
RIGHT MOUNT - INSTALLATION.....9-135,9-51
RIGHT MOUNT - REMOVAL........9-135,9-51
RIGHT OUTBOARD - INSTALLATION,
SEAT BELT & RETRACTOR - SECOND
ROW ..............................8O-14
RIGHT OUTBOARD - REMOVAL, SEAT
BELT & RETRACTOR - SECOND ROW....8O-14
RIGHT OUTBOARD WITH REAR HVAC -
LWB - INSTALLATION, SEAT BELT &
RETRACTOR - SECOND ROW...........8O-15
RIGHT OUTBOARD WITH REAR HVAC -
LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW...........8O-15
RIGHT QUARTER TRIM PANEL -
INSTALLATION.......................23-78
RIGHT QUARTER TRIM PANEL -
REMOVAL..........................23-78
RING, FITTING - PISTON
................9-45
RING FITTING - STANDARD
PROCEDURE, PISTON
.................9-121
RINGS - INSTALLATION, PISTON
........9-121
RINGS - REMOVAL, PISTON
............9-121
RISER - 50/50 SPLIT - INSTALLATION,
BENCH SEAT
........................23-99
RISER - 50/50 SPLIT - REMOVAL,
BENCH SEAT
........................23-99
RISER - INSTALLATION, LUGGAGE RACK
. . 23-55
RISER - INSTALLATION, QUAD BUCKET
SEAT
..............................23-96
RISER - MANUAL TRACK -
INSTALLATION, FRONT SEAT
...........23-93
RISER - MANUAL TRACK - REMOVAL,
FRONT SEAT
........................23-93
RISER - REMOVAL, LUGGAGE RACK
.....23-54
RISER - REMOVAL, QUAD BUCKET SEAT
. . 23-96
RISER - SECOND ROW - INSTALLATION,
BENCH SEAT
.......................23-100RISER - SECOND ROW - REMOVAL,
BENCH SEAT........................23-99
RISER - THIRD ROW - INSTALLATION,
BENCH SEAT.......................23-100
RISER - THIRD ROW - REMOVAL,
BENCH SEAT.......................23-100
RKE TRANSMITTER PROGRAMING -
STANDARD PROCEDURE..............8N-43
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-3
ROAD TEST - DIAGNOSIS AND TESTING . 21-119
ROCKER ARMS - DESCRIPTION.........9-109
ROCKER ARMS - INSPECTION...........9-35
ROCKER ARMS - INSTALLATION.........9-35
ROCKER ARMS - OPERATION...........9-109
ROCKER ARMS - REMOVAL.............9-34
ROCKER ARMS AND SHAFT - ASSEMBLY . 9-109
ROCKER ARMS AND SHAFT -
DISASSEMBLY.......................9-109
ROCKER ARMS AND SHAFT -
INSTALLATION.......................9-110
ROCKER ARMS AND SHAFT - REMOVAL . . 9-109
ROD - DESCRIPTION, LIFT GEAR & LINK . 8N-16
ROD - DESCRIPTION, PISTON &
CONNECTING....................9-116,9-42
ROD - INSTALLATION, LIFT GEAR &
LINK..............................8N-16
ROD - INSTALLATION, OUTER TIE.......19-34
ROD - INSTALLATION, PISTON &
CONNECTING.........................9-44
ROD - OPERATION, LIFT GEAR & LINK.....8N-16
ROD - REMOVAL, LIFT GEAR & LINK.....8N-16
ROD - REMOVAL, OUTER TIE...........19-34
ROD - REMOVAL, PISTON &
CONNECTING.........................9-43
ROD BEARING CLEARANCE - STANDARD
PROCEDURE, MEASURING
CONNECTING........................9-120
ROD, FITTING - CONNECTING............9-45
RODS - STANDARD PROCEDURE,
FITTING CONNECTING.................9-116
ROOF JOINT MOLDING - INSTALLATION . . 23-57
ROOF JOINT MOLDING - REMOVAL......23-57
ROTATION - STANDARD PROCEDURE,
TIRE AND WHEEL.....................22-7
ROTOR - DIAGNOSIS AND TESTING,
BRAKE..............................5-51
ROTOR - INSTALLATION, FRONT BRAKE . . . 5-54
ROTOR - REMOVAL, FRONT BRAKE.......5-54
ROTOR, EXPORT - BRAKE..............5-55
ROTOR MACHINING - STANDARD
PROCEDURE, BRAKE...................5-53
ROTOR, SPECIFICATIONS - BRAKE........5-55
ROW - BENCH - INSTALLATION, SEAT
BELT BUCKLE - FIRST................8O-12
ROW - BENCH - REMOVAL, SEAT BELT
BUCKLE - FIRST.....................8O-12
ROW - INSTALLATION, BENCH SEAT
RISER - SECOND
....................23-100
ROW - INSTALLATION, BENCH SEAT
RISER - THIRD
.....................23-100
ROW - LEFT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR - SECOND
...............8O-16
ROW - LEFT OUTBOARD - REMOVAL,
SEAT BELT & RETRACTOR - SECOND
....8O-16
ROW - OUTBOARD - INSTALLATION,
SEAT BELT & RETRACTOR - FIRST
......8O-13
ROW - OUTBOARD - REMOVAL, SEAT
BELT & RETRACTOR - FIRST
...........8O-13
ROW - REMOVAL, BENCH SEAT RISER -
SECOND
............................23-99
ROW - REMOVAL, BENCH SEAT RISER -
THIRD
............................23-100
ROW - RIGHT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR - SECOND
...............8O-14
ROW - RIGHT OUTBOARD - REMOVAL,
SEAT BELT & RETRACTOR - SECOND
....8O-14
ROW - RIGHT OUTBOARD WITH REAR
HVAC - LWB - INSTALLATION, SEAT
BELT & RETRACTOR - SECOND
.........8O-15
ROW - RIGHT OUTBOARD WITH REAR
HVAC - LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND
...............8O-15
ROW - THREE PASSENGER BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND
...........................8O-14ROW - THREE PASSENGER BENCH -
REMOVAL, SEAT BELT BUCKLE -
SECOND...........................8O-14
ROW INBOARD - 50/50 BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND...........................8O-12
ROW INBOARD - 50/50 BENCH -
REMOVAL, SEAT BELT BUCKLE -
SECOND...........................8O-12
ROW INBOARD - QUAD BUCKET -
INSTALLATION, SEAT BELT BUCKLE -
FIRST.............................8O-11
ROW INBOARD - QUAD BUCKET -
REMOVAL, SEAT BELT BUCKLE - FIRST . . . 8O-11
RUN WEATHERSTRIP - INSTALLATION,
FRONT DOOR GLASS................23-110
RUN WEATHERSTRIP - REMOVAL,
FRONT DOOR GLASS................23-110
RUNOUT - DIAGNOSIS AND TESTING,
CLUTCH COVER AND DISC...............6-6
RUNOUT, SPECIFICATIONS - TONE
WHEEL.............................5-79
SAFETY CERTIFICATION LABEL -
DESCRIPTION, VEHICLE.............Intro.-11
SAFETY PRECAUTIONS AND WARNINGS,
WARNING...........................23-1
SAFETY PRECAUTIONS, WARNING -
WINDSHIELD.......................23-105
SANDING/BUFFING & POLISHING -
DESCRIPTION, FINESSE...............23-84
SBEC CONTROLLER - INSTALLATION.....8E-17
SBEC CONTROLLER - OPERATION,
8-VOLT SUPPLY - PCM OUTPUT.........8E-15
SBEC CONTROLLER - REMOVAL.........8E-16
SCHEDULES - DESCRIPTION,
MAINTENANCE........................0-7
SCHEMATICS AND DIAGRAMS - 41TE
TRANSAXLE HYDRAULIC SCHEMATICS . . 21-169
SCHEMATICS, SCHEMATICS AND
DIAGRAMS - 41TE TRANSAXLE
HYDRAULIC........................21-169
SCREEN - DESCRIPTION, VIDEO........8A-16
SCREEN - INSTALLATION, VIDEO........8A-16
SCREEN - OPERATION, VIDEO..........8A-16
SCREEN - REMOVAL, VIDEO............8A-16
SCUFF PAD - INSTALLATION, REAR
FASCIA..............................13-4
SCUFF PAD - REMOVAL, REAR FASCIA....13-3
SDP POWER TRANSFER UNIT, SPECIAL
TOOLS..............................21-8
SEAL - ASSEMBLY, CALIPER PISTON . . 5-26,5-29
SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP TO FILLER NECK.........7-27
SEAL - DISASSEMBLY, CALIPER PISTON . . . 5-24,
5-28
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL................9-127,9-40
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL................9-127,9-40
SEAL - INSTALLATION, DIFFERENTIAL
CARRIER............................21-9
SEAL - INSTALLATION, END COVER......21-11
SEAL - INSTALLATION, HALF SHAFT
INNER.............................21-12
SEAL - INSTALLATION, INPUT FLANGE....3-45
SEAL - INSTALLATION, INPUT SHAFT.....21-18
SEAL - INSTALLATION, INPUT SHAFT
COVER.............................21-14
SEAL - INSTALLATION, INPUT SHAFT
END ...............................21-16
SEAL - INSTALLATION, OUTER HALF
SHAFT.............................21-19
SEAL - INSTALLATION, OUTPUT FLANGE . . . 3-46
SEAL - OIL PUMP - INSTALLATION.....21-233
SEAL - OIL PUMP - REMOVAL.........21-232
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL................9-129,9-42
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL ...........................9-128,9-41
SEAL - REMOVAL, DIFFERENTIAL
CARRIER............................21-9
SEAL - REMOVAL, END COVER..........21-11
SEAL - REMOVAL, HALF SHAFT INNER . . . 21-12
SEAL - REMOVAL, INPUT FLANGE
........3-44
SEAL - REMOVAL, INPUT SHAFT
........21-17
SEAL - REMOVAL, INPUT SHAFT COVER
. . 21-13
SEAL - REMOVAL, INPUT SHAFT END
....21-15
SEAL - REMOVAL, OUTER HALF SHAFT
. . . 21-19
RSINDEX27
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

TEMPERATURE SENSOR - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-22
TEMPERATURE SENSOR - 3.3/3.8L -
REMOVAL, ENGINE COOLANT............7-21
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - DESCRIPTION,
EVAPORATOR.......................24-22
TEMPERATURE SENSOR - DESCRIPTION,
INFRARED.....................24-23,24-35
TEMPERATURE SENSOR - DESCRIPTION,
INLET AIR..........................14-29
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT..............8M-12
TEMPERATURE SENSOR -
INSTALLATION, EVAPORATOR...........24-23
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - OPERATION,
EVAPORATOR.......................24-23
TEMPERATURE SENSOR - OPERATION,
INFRARED.....................24-24,24-35
TEMPERATURE SENSOR - OPERATION,
INLET AIR..........................14-29
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-23
TEMPERATURE SENSOR - REMOVAL,
EVAPORATOR.......................24-23
TEMPERATURE SENSOR -
SPECIFICATIONS, BATTERY.............8F-22
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT....8M-12
TENSION - STANDARD PROCEDURE,
CHECKING POWER STEERING BELT.........7-8
TENSION RELEASE - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER................5-58
TENSION RESET - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER................5-59
TENSION, SPECIFICATIONS -
ACCESSORY DRIVE BELT................7-5
TENSIONER - 2.4L - INSTALLATION,
BELT ...............................7-10
TENSIONER - 2.4L - REMOVAL, BELT......7-10
TENSIONER - 3.3/3.8L - INSTALLATION,
BELT ...............................7-12
TENSIONER - 3.3/3.8L - REMOVAL, BELT . . . 7-12
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-16
TENSIONER - OPERATION, SEAT BELT....8O-16
TENSIONER & PULLEY - INSTALLATION,
TIMING BELT.........................9-69
TENSIONER & PULLEY - REMOVAL,
TIMING BELT.........................9-68
TERMINAL - INSTALLATION.........8W-01-14
TERMINAL - REMOVAL.............8W-01-14
TERMINAL REPAIR - STANDARD
PROCEDURE, GRID LINE...............8G-3
TEST - DIAGNOSIS AND TESTING, A/C
COOL DOWN.........................24-4
TEST - DIAGNOSIS AND TESTING, A/C
PERFORMANCE.......................24-5
TEST - DIAGNOSIS AND TESTING,
CONTROL CIRCUIT...................8F-30
TEST - DIAGNOSIS AND TESTING,
COOLING SYSTEM LEAK.................7-2
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE
LEAKAGE.........................9-83,9-9
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION PRESSURE . . 9-83,9-9
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT............................8F-33
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT RESISTANCE.................8F-32
TEST - DIAGNOSIS AND TESTING,
HEATED MIRROR.....................8G-5
TEST - DIAGNOSIS AND TESTING,
HEATER PERFORMANCE................24-6
TEST - DIAGNOSIS AND TESTING,
POWER STEERING SYSTEM FLOW
AND PRESSURE
......................19-1
TEST - DIAGNOSIS AND TESTING, ROAD
. . . 8P-3
TEST - DIAGNOSIS AND TESTING, ROAD
. 21-119
TEST - DIAGNOSIS AND TESTING,
STARTING SYSTEM
...................8F-28
TEST - DIAGNOSIS AND TESTING,
SYSTEM
............................8G-3TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-13
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-13
TEST MODE, OPERATION - DRB IIIT
STATE DISPLAY.......................25-9
TESTS - DIAGNOSIS AND TESTING,
CLUTCH AIR PRESSURE..............21-122
TESTS - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE..............21-120
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-1
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-3
THERMOSTAT - 2.4L - INSTALLATION,
ENGINE COOLANT.....................7-23
THERMOSTAT - 2.4L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-24
THERMOSTAT - 3.3/3.8L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - DESCRIPTION, ENGINE
COOLANT............................7-22
THERMOSTAT - DIAGNOSIS AND
TESTING, ENGINE COOLANT.............7-23
THERMOSTAT - OPERATION, ENGINE
COOLANT............................7-22
THERMOWRAP - DESCRIPTION.........8F-19
THERMOWRAP - INSTALLATION.........8F-19
THERMOWRAP - OPERATION...........8F-19
THERMOWRAP - REMOVAL............8F-19
THIRD ROW - INSTALLATION, BENCH
SEAT RISER........................23-100
THIRD ROW - REMOVAL, BENCH SEAT
RISER............................23-100
THREAD REPAIR - DESCRIPTION, FRONT
CRADLE CROSSMEMBER...............13-9
THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD STRIPPED......9-145
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-5
THREADS - STANDARD PROCEDURE,
REPAIR OF DAMAGED OR WORN.....9-10,9-86
THREE PASSENGER BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW.......................8O-14
THREE PASSENGER BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-14
THREE ZONE - DESCRIPTION, MANUAL....24-1
THREE ZONE - OPERATION, MANUAL.....24-3
THREE ZONE ATC - OPERATION..........24-3
THROTTLE BODY - DESCRIPTION........14-34
THROTTLE BODY - INSTALLATION.......14-35
THROTTLE BODY - OPERATION.........14-34
THROTTLE BODY - REMOVAL...........14-35
THROTTLE CONTROL CABLE -
INSTALLATION.......................14-35
THROTTLE CONTROL CABLE - REMOVAL . . 14-35
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-36
THROTTLE POSITION SENSOR -
OPERATION.........................14-36
TIE ROD - INSTALLATION, OUTER.......19-34
TIE ROD - REMOVAL, OUTER...........19-34
TIMING BELT - INSTALLATION...........9-65
TIMING BELT - REMOVAL
...............9-63
TIMING BELT COVER(S) - INSTALLATION
. . . 9-62
TIMING BELT COVER(S) - REMOVAL
......9-61
TIMING BELT TENSIONER & PULLEY -
INSTALLATION
........................9-69
TIMING BELT TENSIONER & PULLEY -
REMOVAL
...........................9-68
TIMING CHAIN AND CAMSHAFT
SPROCKET - INSTALLATION
............9-157
TIMING CHAIN AND CAMSHAFT
SPROCKET - REMOVAL
................9-156
TIMING CHAIN COVER - INSTALLATION
. . . 9-155
TIMING CHAIN COVER - REMOVAL
......9-153
TIMING CHAIN WEAR - STANDARD
PROCEDURE, MEASURING
.............9-153
TIMING VERIFICATION - STANDARD
PROCEDURE, VALVE
..................9-153
TIRE - DESCRIPTION
..................22-13
TIRE AND WHEEL ASSEMBLY
(ALUMINUM WHEEL) - INSTALLATION
.....22-8TIRE AND WHEEL ASSEMBLY
(ALUMINUM WHEEL) - REMOVAL........22-7
TIRE AND WHEEL ASSEMBLY (STEEL
WHEEL) - INSTALLATION...............22-8
TIRE AND WHEEL ASSEMBLY (STEEL
WHEEL) - REMOVAL...................22-8
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-5
TIRE AND WHEEL MATCH MOUNTING -
STANDARD PROCEDURE................22-7
TIRE AND WHEEL ROTATION -
STANDARD PROCEDURE................22-7
TIRE AND WHEEL VIBRATION -
DIAGNOSIS AND TESTING..............22-1
TIRE INFLATION PRESSURES -
STANDARD PROCEDURE...............22-16
TIRE LEAK REPAIRING - STANDARD
PROCEDURE........................22-17
TIRE NOISE - DIAGNOSIS AND TESTING . . 22-14
TIRE PRESSURE FOR HIGH SPEED
OPERATION - STANDARD PROCEDURE . . . 22-17
TIRE PRESSURE MONITORING -
DESCRIPTION........................22-9
TIRE PRESSURE MONITORING -
OPERATION..........................22-9
TIRE PRESSURE SENSOR - DIAGNOSIS
AND TESTING.......................22-10
TIRE PRESSURE SENSOR RETRAIN -
STANDARD PROCEDURE...............22-10
TIRE (TEMPORARY) - DESCRIPTION,
SPARE .............................22-14
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING.......................22-16
TIRES - CLEANING...................22-17
TIRES - DESCRIPTION, RADIAL-PLY......22-14
TIRES - DESCRIPTION, REPLACEMENT . . . 22-14
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING...........................22-14
TO CYLINDER BORE FITTING -
STANDARD PROCEDURE, PISTON........9-42
TO FILLER NECK SEAL - DIAGNOSIS
AND TESTING, RADIATOR CAP...........7-27
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-9
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . 8W-01-10
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TONE WHEEL - INSPECTION.............5-82
TONE WHEEL RUNOUT, SPECIFICATIONS . . . 5-79
TOOLS - 2.4L ENGINE, SPECIAL..........9-21
TOOLS - 3.3/3.8L ENGINE, SPECIAL.......9-95
TOOLS - 41TE AUTOMATIC TRANSAXLE,
SPECIAL..........................21-183
TOOLS - BASE BRAKE SYSTEM, SPECIAL . . 5-10
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL......................8F-7
TOOLS - BODY, SPECIAL...............23-13
TOOLS - COOLING SYSTEM, SPECIAL......7-6
TOOLS - EXHAUST SYSTEM, SPECIAL.....11-4
TOOLS - FRONT SUSPENSION, SPECIAL....2-3
TOOLS - FUEL, SPECIAL...........14-23,14-3
TOOLS - OVERHEAD CONSOLE, SPECIAL . . 8M-6
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-34
TOOLS - POWER STEERING PUMP,
SPECIAL...........................19-43
TOOLS - POWER STEERING, SPECIAL.....19-9
TOOLS - REAR SUSPENSION, SPECIAL....2-28
TOOLS - SDP POWER TRANSFER UNIT,
SPECIAL............................21-8
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, DIAGNOSIS AND TESTING -
SPECIAL............................3-34
TOOLS, SPECIAL TOOLS - BATTERY
SYSTEM SPECIAL.....................8F-7
TOOLS, SPECIFICATIONS - SPECIAL......8F-23
TOOLS, T850 TRANSAXLE - SPECIAL
.......6-6
TOOLS, T850 TRANSAXLE - SPECIAL
.....21-58
TOP COVER - INSTALLATION,
INSTRUMENT PANEL
..................23-67
TOP COVER - REMOVAL, INSTRUMENT
PANEL
.............................23-67
TOP PAD ASSEMBLY - INSTALLATION,
INSTRUMENT PANEL
..................23-70
RSINDEX33
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

TOP PAD ASSEMBLY - REMOVAL,
INSTRUMENT PANEL..................23-70
TORQUES, SPECIFICATIONS............8F-33
TOUCH-UP - DESCRIPTION, PAINTED.....23-84
TOWING - STANDARD PROCEDURE.......0-17
TPM - CAUTION, SENSOR..............22-10
TPM - DESCRIPTION, SENSOR..........22-10
TPM - INSTALLATION, SENSOR.........22-12
TPM - OPERATION, SENSOR............22-10
TPM - REMOVAL, SENSOR.............22-11
TRACK - DESCRIPTION, DRIVER POWER
SEAT ..............................8N-58
TRACK - DESCRIPTION, PASSENGER
POWER SEAT.......................8N-59
TRACK - DIAGNOSIS AND TESTING,
DRIVER POWER SEAT................8N-58
TRACK - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-60
TRACK - INSTALLATION, BENCH SEAT . . . 23-102
TRACK - INSTALLATION, DRIVER POWER
SEAT ..............................8N-59
TRACK - INSTALLATION, FRONT SEAT
RISER - MANUAL....................23-93
TRACK - INSTALLATION, PASSENGER
POWER SEAT.......................8N-61
TRACK - OPERATION, DRIVER POWER
SEAT ..............................8N-58
TRACK - OPERATION, PASSENGER
POWER SEAT.......................8N-60
TRACK & RACK - DESCRIPTION, LOWER
DRIVE UNIT..........................8N-34
TRACK & RACK - INSTALLATION,
LOWER DRIVE UNIT..................8N-34
TRACK & RACK - OPERATION, LOWER
DRIVE UNIT........................8N-34
TRACK & RACK - REMOVAL, LOWER
DRIVE UNIT........................8N-34
TRACK - REAR COVER - INSTALLATION,
FRONT SEAT........................23-95
TRACK - REAR COVER - REMOVAL,
FRONT SEAT........................23-95
TRACK - REMOVAL, BENCH SEAT.......23-102
TRACK - REMOVAL, DRIVER POWER
SEAT ..............................8N-59
TRACK - REMOVAL, FRONT SEAT RISER
- MANUAL..........................23-93
TRACK - REMOVAL, PASSENGER POWER
SEAT ..............................8N-61
TRACK BAR - DESCRIPTION.............2-44
TRACK BAR - INSTALLATION............2-45
TRACK BAR - OPERATION...............2-44
TRACK BAR - REMOVAL................2-44
TRACK MANUAL ADJUSTER -
INSTALLATION, FRONT SEAT...........23-94
TRACK MANUAL ADJUSTER - REMOVAL,
FRONT SEAT........................23-94
TRACK POWER ADJUSTER -
INSTALLATION, FRONT SEAT...........23-94
TRACK POWER ADJUSTER - REMOVAL,
FRONT SEAT........................23-94
TRACTION CONTROL SWITCH -
DIAGNOSIS AND TESTING..............5-82
TRACTION CONTROL SYSTEM -
DESCRIPTION........................5-76
TRACTION CONTROL SYSTEM -
OPERATION..........................5-77
TRANSAXLE - ASSEMBLY, T850 MANUAL
. 21-42
TRANSAXLE - DESCRIPTION, 41TE
AUTOMATIC
........................21-117
TRANSAXLE - DESCRIPTION, T850
MANUAL
...........................21-21
TRANSAXLE - DISASSEMBLY, T850
MANUAL
...........................21-35
TRANSAXLE - INSTALLATION, T850
MANUAL
...........................21-51
TRANSAXLE - OPERATION, 41TE
AUTOMATIC
........................21-119
TRANSAXLE - OPERATION, T850
MANUAL
...........................21-24
TRANSAXLE - REMOVAL, T850 MANUAL
. . 21-31
TRANSAXLE - SPECIAL TOOLS, T850
.......6-6
TRANSAXLE - SPECIAL TOOLS, T850
.....21-58
TRANSAXLE - SPECIFICATIONS, 41TE
. . . 21-181
TRANSAXLE - SPECIFICATIONS, T850
MANUAL
...........................21-56
TRANSAXLE GENERAL DIAGNOSIS -
DIAGNOSIS AND TESTING, 41TE
.......21-119TRANSAXLE HYDRAULIC SCHEMATICS,
SCHEMATICS AND DIAGRAMS - 41TE . . . 21-169
TRANSAXLE, SPECIAL TOOLS - 41TE
AUTOMATIC........................21-183
TRANSDUCER - DESCRIPTION, A/C
PRESSURE.........................24-10
TRANSDUCER - DIAGNOSIS AND
TESTING, A/C PRESSURE..............24-10
TRANSDUCER - INSTALLATION, A/C
PRESSURE.........................24-11
TRANSDUCER - OPERATION, A/C
PRESSURE.........................24-10
TRANSDUCER - REMOVAL, A/C
PRESSURE.........................24-10
TRANSFER UNIT - DESCRIPTION,
POWER.............................21-1
TRANSFER UNIT - OPERATION, POWER....21-3
TRANSFER UNIT, SPECIAL TOOLS - SDP
POWER.............................21-8
TRANSMISSION CONTROL MODULE -
DESCRIPTION.......................8E-20
TRANSMISSION CONTROL MODULE -
OPERATION.........................8E-20
TRANSMISSION CONTROL RELAY -
DESCRIPTION......................21-247
TRANSMISSION CONTROL RELAY -
OPERATION........................21-248
TRANSMISSION FLUID - DESCRIPTION.....0-4
TRANSMISSION OIL COOLER -
DESCRIPTION........................7-37
TRANSMISSION OIL COOLER -
INSPECTION.........................7-37
TRANSMISSION OIL COOLER -
INSTALLATION........................7-37
TRANSMISSION OIL COOLER -
REMOVAL...........................7-37
TRANSMISSION OIL COOLER LINES -
INSTALLATION........................7-38
TRANSMISSION OIL COOLER LINES -
REMOVAL...........................7-38
TRANSMISSION RANGE SENSOR -
DESCRIPTION......................21-248
TRANSMISSION RANGE SENSOR -
INSTALLATION......................21-249
TRANSMISSION RANGE SENSOR -
OPERATION........................21-248
TRANSMISSION RANGE SENSOR -
REMOVAL.........................21-249
TRANSMITTER - DESCRIPTION,
UNIVERSAL........................8M-10
TRANSMITTER - DIAGNOSIS AND
TESTING, KEYLESS ENTRY.............8N-42
TRANSMITTER - DIAGNOSIS AND
TESTING, UNIVERSAL................8M-10
TRANSMITTER - OPERATION,
UNIVERSAL........................8M-10
TRANSMITTER CODES - STANDARD
PROCEDURE, ERASING...............8M-11
TRANSMITTER CODES - STANDARD
PROCEDURE, SETTING................8M-11
TRANSMITTER PROGRAMING -
STANDARD PROCEDURE, RKE..........8N-43
TRANSPONDER KEY - DESCRIPTION......8Q-3
TRANSPONDER KEY - OPERATION........8Q-3
TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE...............8Q-4
TRANSVERSE BRACKET - DESCRIPTION . . 8N-18
TRANSVERSE BRACKET - INSTALLATION . . 8N-18
TRANSVERSE BRACKET - OPERATION....8N-18
TRANSVERSE BRACKET - REMOVAL.....8N-18
TRAY - BRACKET ASSEMBLY -
INSTALLATION, FLOOR CONSOLE
........23-82
TRAY - BRACKET ASSEMBLY -
REMOVAL, FLOOR CONSOLE
...........23-82
TRAY - DESCRIPTION, BATTERY
.........8F-18
TRAY - INSTALLATION, BATTERY
........8F-19
TRAY - INSTALLATION, FLOOR CONSOLE
. . 23-81
TRAY - OPERATION, BATTERY
..........8F-19
TRAY - REMOVAL, BATTERY
............8F-19
TRAY - REMOVAL, FLOOR CONSOLE
.....23-81
TRD LINK - DESCRIPTION
............21-249
TRD LINK - OPERATION
..............21-249
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING
.......................22-16
TRIM - INSTALLATION, A-PILLAR
........23-73
TRIM - INSTALLATION, A-PILLAR
LOWER EXTENSION
..................23-73TRIM - INSTALLATION, B-PILLAR
LOWER............................23-74
TRIM - INSTALLATION, B-PILLAR UPPER . . 23-74
TRIM - INSTALLATION, COWL..........23-75
TRIM - INSTALLATION, C-PILLAR........23-76
TRIM - INSTALLATION, REAR HEADER....23-79
TRIM - REMOVAL, A-PILLAR...........23-73
TRIM - REMOVAL, A-PILLAR LOWER
EXTENSION.........................23-73
TRIM - REMOVAL, B-PILLAR LOWER.....23-73
TRIM - REMOVAL, B-PILLAR UPPER.....23-74
TRIM - REMOVAL, COWL..............23-75
TRIM - REMOVAL, C-PILLAR...........23-75
TRIM - REMOVAL, REAR HEADER.......23-79
TRIM BOLSTER - INSTALLATION,
QUARTER..........................23-77
TRIM BOLSTER - REMOVAL, QUARTER . . . 23-77
TRIM COVER - INSTALLATION, DRIVER
AIRBAG.............................8O-7
TRIM COVER - REMOVAL, DRIVER
AIRBAG.............................8O-6
TRIM PANEL - INSTALLATION.....23-20,23-33,
23-43
TRIM PANEL - INSTALLATION, LEFT
D-PILLAR...........................23-77
TRIM PANEL - INSTALLATION, LEFT
QUARTER..........................23-78
TRIM PANEL - INSTALLATION, RIGHT
D-PILLAR...........................23-80
TRIM PANEL - INSTALLATION, RIGHT
QUARTER..........................23-78
TRIM PANEL - REMOVAL....23-20,23-33,23-42
TRIM PANEL - REMOVAL, LEFT
D-PILLAR...........................23-77
TRIM PANEL - REMOVAL, LEFT
QUARTER..........................23-78
TRIM PANEL - REMOVAL, RIGHT
D-PILLAR...........................23-80
TRIM PANEL - REMOVAL, RIGHT
QUARTER..........................23-78
TRIM PLATE - INSTALLATION, DOOR
SILL...............................23-76
TRIM PLATE - REMOVAL, DOOR SILL....23-76
TRIP DEFINITION - DESCRIPTION.........25-1
TROUBLE CODES - STANDARD
PROCEDURE, OBTAINING DIAGNOSTIC . . . 8E-15
TUBE - 2.4L - DESCRIPTION, WATER
PUMP INLET.........................7-35
TUBE - 2.4L - INSTALLATION, WATER
PUMP INLET.........................7-35
TUBE - 2.4L - REMOVAL, WATER PUMP
INLET...............................7-35
TUBE - 3.3/3.8L - INSTALLATION, WATER
PUMP INLET.........................7-36
TUBE - 3.3/3.8L - REMOVAL, WATER
PUMP INLET.........................7-36
TUBE - INSTALLATION, DRAIN.........23-117
TUBE - INSTALLATION, EXHAUST.......24-107
TUBE - INSTALLATION, FUEL TANK
FILLER.............................14-12
TUBE - REMOVAL, DRAIN.............23-116
TUBE - REMOVAL, EXHAUST..........24-107
TUBE - REMOVAL, FUEL TANK FILLER....14-12
TUBES - INSTALLATION, HEATER CORE
EXTENSION.........................24-77
TUBES - REMOVAL, HEATER CORE
EXTENSION
.........................24-75
TUBES AND HOSES - DESCRIPTION,
BRAKE
..............................5-14
TUBES AND HOSES - INSPECTION,
BRAKE
..............................5-14
TUBES AND HOSES - OPERATION,
BRAKE
..............................5-14
TURN SIGNAL SYSTEM - DESCRIPTION
. . . 8L-21
TURN SIGNAL SYSTEM - OPERATION
....8L-21
TURNING TORQUE - ADJUSTMENT,
DIFFERENTIAL
.......................21-69
TWO ZONE ATC - OPERATION
..........24-106
UNDER SEAT STORAGE BIN -
INSTALLATION
......................23-103
UNDER SEAT STORAGE BIN - REMOVAL
. 23-103
UNDER SEAT STORAGE BIN GUIDE -
INSTALLATION
......................23-104
UNDER SEAT STORAGE BIN GUIDE -
REMOVAL
.........................23-104
UNDER SEAT STORAGE BIN LOCK/LATCH
- INSTALLATION
....................23-104
34 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

UNDER SEAT STORAGE BIN LOCK/LATCH
- REMOVAL........................23-104
UNDERBODY LINES - DESCRIPTION.....24-103
UNDERBODY LINES - OPERATION......24-103
UNIT - DESCRIPTION, LOWER DRIVE....8N-32
UNIT - DESCRIPTION, POWER
TRANSFER...........................21-1
UNIT - EXPORT - INSTALLATION,
HEADLAMP.........................8L-20
UNIT - EXPORT - REMOVAL, HEADLAMP . . 8L-20
UNIT - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP.................8L-7
UNIT - INSTALLATION, HEATER........24-111
UNIT - INSTALLATION, LOWER DRIVE....8N-33
UNIT - INSTALLATION, TAIL LAMP.......8L-23
UNIT - OPERATION, LOWER DRIVE......8N-32
UNIT - OPERATION, POWER TRANSFER....21-3
UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP.................8L-6
UNIT - REMOVAL, HEATER............24-111
UNIT - REMOVAL, LOWER DRIVE.......8N-33
UNIT - REMOVAL, TAIL LAMP...........8L-23
UNIT / SENSOR - DESCRIPTION, FUEL
LEVEL SENDING......................14-4
UNIT / SENSOR - INSTALLATION, FUEL
LEVEL SENDING......................14-5
UNIT / SENSOR - OPERATION, FUEL
LEVEL SENDING......................14-5
UNIT / SENSOR - REMOVAL, FUEL
LEVEL SENDING........................14-5
UNIT ALIGNMENT - EXPORT -
STANDARD PROCEDURE, FRONT FOG
LAMP...............................8L-9
UNIT ALIGNMENT - EXPORT -
STANDARD PROCEDURE, HEADLAMP....8L-17
UNIT ALIGNMENT - STANDARD
PROCEDURE, FRONT FOG LAMP.........8L-9
UNIT ALIGNMENT - STANDARD
PROCEDURE, HEADLAMP..............8L-17
UNIT, SPECIAL TOOLS - SDP POWER
TRANSFER...........................21-8
UNIT TRACK & RACK - DESCRIPTION,
LOWER DRIVE......................8N-34
UNIT TRACK & RACK - INSTALLATION,
LOWER DRIVE......................8N-34
UNIT TRACK & RACK - OPERATION,
LOWER DRIVE......................8N-34
UNIT TRACK & RACK - REMOVAL,
LOWER DRIVE......................8N-34
UNIVERSAL TRANSMITTER -
DESCRIPTION.......................8M-10
UNIVERSAL TRANSMITTER - DIAGNOSIS
AND TESTING.......................8M-10
UNIVERSAL TRANSMITTER - OPERATION . 8M-10
UPPER - INSPECTION, INTAKE
MANIFOLD...........................9-59
UPPER - INSTALLATION, INTAKE
MANIFOLD...........................9-59
UPPER - INSTALLATION, SHROUD.......19-23
UPPER - REMOVAL, INTAKE MANIFOLD....9-58
UPPER - REMOVAL, SHROUD...........19-23
UPPER HINGE - INSTALLATION.........23-35
UPPER HINGE - REMOVAL.............23-35
UPPER INTAKE MANIFOLD -
INSTALLATION.......................9-147
UPPER INTAKE MANIFOLD - REMOVAL . . . 9-145
UPPER TRIM - INSTALLATION, B-PILLAR
. . 23-74
UPPER TRIM - REMOVAL, B-PILLAR
.....23-74
UPSTOP SWITCH - INSTALLATION,
CLUTCH PEDAL
.......................6-16
UPSTOP SWITCH - REMOVAL, CLUTCH
PEDAL
..............................6-15
UPSTREAM 1/1 - 2.4L - INSTALLATION
. . . 14-33
UPSTREAM 1/1 - 2.4L - REMOVAL
.......14-33
UPSTREAM 1/1 - 3.3/3.8L -
INSTALLATION
.......................14-34
UPSTREAM 1/1 - 3.3/3.8L - REMOVAL
....14-33
USAGE - DESCRIPTION, FASTENER
.....Intro.-5
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO
.............8W-01-1
USING PLASTIGAGE - STANDARD
PROCEDURE, MEASURING BEARING
CLEARANCE
.....................9-12,9-84
VAC LEAK DETECTION ASSY -
INSTALLATION, NATURAL
..............25-13
VAC LEAK DETECTION ASSY -
REMOVAL, NATURAL
..................25-13VACUUM PORT REPAIR - STANDARD
PROCEDURE, INTAKE MANIFOLD........9-145
VACUUM RESERVOIR - DESCRIPTION.....8P-6
VACUUM RESERVOIR - INSTALLATION....8P-6
VACUUM RESERVOIR - OPERATION.......8P-6
VACUUM RESERVOIR - REMOVAL........8P-6
VALVE - DESCRIPTION................25-22
VALVE - DESCRIPTION, EXPANSION . 24-72,24-96
VALVE - DESCRIPTION, PCV............25-16
VALVE - DIAGNOSIS AND TESTING,
EXPANSION....................24-72,24-97
VALVE - INSTALLATION, EXPANSION.....24-74,
24-98
VALVE - INSTALLATION, OIL PRESSURE
RELIEF.............................9-141
VALVE - OPERATION..................25-22
VALVE - OPERATION, EXPANSION . . 24-72,24-97
VALVE - OPERATION, PCV..............25-16
VALVE - REMOVAL, EXPANSION....24-73,24-97
VALVE - REMOVAL, OIL PRESSURE
RELIEF.............................9-141
VALVE BODY - ASSEMBLY............21-257
VALVE BODY - DESCRIPTION..........21-250
VALVE BODY - DISASSEMBLY..........21-252
VALVE BODY - INSTALLATION..........21-262
VALVE BODY - OPERATION............21-250
VALVE BODY - REMOVAL.............21-251
VALVE (HEIGHT SENSING) -
DESCRIPTION, PROPORTIONING.........5-48
VALVE (HEIGHT SENSING) - DIAGNOSIS
AND TESTING, PROPORTIONING.........5-49
VALVE (HEIGHT SENSING) -
INSTALLATION, PROPORTIONING.........5-51
VALVE (HEIGHT SENSING) - OPERATION,
PROPORTIONING.....................5-48
VALVE (HEIGHT SENSING) - REMOVAL,
PROPORTIONING.....................5-50
VALVE SEATS - STANDARD PROCEDURE,
REFACING VALVES...................9-104
VALVE SPRINGS - DESCRIPTION........9-106
VALVE SPRINGS - OPERATION..........9-106
VALVE STEM SEALS - DESCRIPTION.....9-111
VALVE STEM SEALS - INSTALLATION.....9-112
VALVE STEM SEALS - REMOVAL........9-112
VALVE TIMING VERIFICATION -
STANDARD PROCEDURE...............9-153
VALVES - OPERATION, HYDRAULIC
CIRCUITS............................5-83
VALVES & SEATS - CLEANING,
INTAKE/EXHAUST................9-105,9-32
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST................9-104,9-32
VALVES & SEATS - INSPECTION,
INTAKE/EXHAUST....................9-105
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST....................9-106
VALVES & SEATS - OPERATION,
INTAKE/EXHAUST....................9-104
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST....................9-105
VALVES AND VALVE SEATS - STANDARD
PROCEDURE, REFACING...............9-104
VANITY LAMP - INSTALLATION.........8L-28
VANITY LAMP - REMOVAL.............8L-28
VAPOR CANISTER - DESCRIPTION
.......25-18
VAPOR CANISTER - OPERATION
.........25-18
VARIABLE BRAKE PROPORTIONING -
DESCRIPTION, ELECTRONIC
.............5-75
VARIABLE BRAKE PROPORTIONING -
OPERATION, ELECTRONIC
...............5-77
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS
...............8M-5
VECI LABEL - DESCRIPTION
..........Intro.-11
VEHICLE DOES NOT FILL - DIAGNOSIS
AND TESTING
.......................25-16
VEHICLE EMISSION CONTROL
INFORMATION LABEL - DESCRIPTION
.....25-1
VEHICLE IDENTIFICATION -
DESCRIPTION
........................23-1
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION
......................Intro.-9
VEHICLE INFO CENTER - DESCRIPTION,
ELECTRONIC
........................8M-6
VEHICLE INFO CENTER - INSTALLATION,
ELECTRONIC
........................8M-9
VEHICLE INFO CENTER - OPERATION,
ELECTRONIC
........................8M-7VEHICLE INFO CENTER - REMOVAL,
ELECTRONIC........................8M-9
VEHICLE INFORMATION CENTER -
DIAGNOSIS AND TESTING,
ELECTRONIC........................8M-7
VEHICLE INFORMATION CENTER
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC.............8M-7
VEHICLE SAFETY CERTIFICATION LABEL
- DESCRIPTION....................Intro.-11
VEHICLE SPEED SENSOR -
INSTALLATION......................21-115
VEHICLE SPEED SENSOR - REMOVAL . . . 21-115
VEHICLE THEFT SECURITY -
DESCRIPTION........................8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-1
VEHICLE THEFT SECURITY SYSTEM -
DIAGNOSIS AND TESTING..............8Q-3
VENT WINDOW MOTOR - DIAGNOSIS
AND TESTING.......................8N-63
VENT WINDOW MOTOR - INSTALLATION . . 8N-64
VENT WINDOW MOTOR - REMOVAL.....8N-63
VERIFICATION - STANDARD
PROCEDURE, VALVE TIMING...........9-153
VIBRATION - DIAGNOSIS AND TESTING,
TIRE AND WHEEL.....................22-1
VIBRATION DAMPER - INSTALLATION....9-130,
9-47
VIBRATION DAMPER - REMOVAL....9-130,9-47
VIDEO SCREEN - DESCRIPTION.........8A-16
VIDEO SCREEN - INSTALLATION........8A-16
VIDEO SCREEN - OPERATION............8A-16
VIDEO SCREEN - REMOVAL............8A-16
VIEW MIRROR - INSTALLATION, REAR . . . 23-80
VIEW MIRROR - INSTALLATION, SIDE....23-57
VIEW MIRROR - REMOVAL, REAR.......23-79
VIEW MIRROR - REMOVAL, SIDE........23-57
VIEW MIRROR GLASS - INSTALLATION,
SIDE..............................23-58
VIEW MIRROR GLASS - REMOVAL, SIDE . . 23-58
VISCOUS COUPLER - DESCRIPTION.......3-41
VISCOUS COUPLER - OPERATION........3-42
VISOR - INSTALLATION, SUN...........23-81
VISOR - REMOVAL, SUN...............23-81
VISOR SUPPORT - INSTALLATION, SUN . . . 23-81
VISOR SUPPORT - REMOVAL, SUN......23-81
VOLT SUPPLY - PCM OUTPUT -
OPERATION, 5.......................8E-15
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION....8F-27
VOLTAGE REGULATOR - OPERATION.....8F-27
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT...........8F-13
VTSS/SKIS INDICATOR LAMP -
DESCRIPTION........................8Q-5
VTSS/SKIS INDICATOR LAMP -
OPERATION..........................8Q-5
WARNING - INSTALLATION............23-106
WARNING - INSTALLATION.............19-13
WARNING - REMOVAL...............23-105
WARNING - REMOVAL................19-12
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - WARNING................24-61
WARNING - WARNINGS AND CAUTIONS . . 19-10,
19-27
WARNING - WINDSHIELD SAFETY
PRECAUTIONS......................23-105
WARNING, A/C PLUMBING.............24-61
WARNING, CHIME/BUZZER..............8B-1
WARNING, DESCRIPTION................5-4
WARNING, DESCRIPTION..............19-37
WARNING, LAMPS/LIGHTING -
EXTERIOR...........................8L-4
WARNING, RESTRAINTS................8O-2
WARNING, WARNING.................24-61
WARNINGS AND CAUTIONS, WARNING
. . 19-10,
19-27
WARNINGS, GENERAL
..............8W-01-7
WARNINGS, WARNING - SAFETY
PRECAUTIONS
........................23-1
WASHER FLUID LEVEL SWITCH -
INSTALLATION
......................8R-16
WASHER FLUID LEVEL SWITCH -
REMOVAL
..........................8R-15
RSINDEX35
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

WASHER HOSE - EXPORT -
INSTALLATION, HEADLAMP............8R-12
WASHER HOSE - EXPORT - REMOVAL,
HEADLAMP.........................8R-12
WASHER HOSES - INSTALLATION.......8R-16
WASHER HOSES - REMOVAL...........8R-16
WASHER PUMP MOTOR - EXPORT -
INSTALLATION, HEADLAMP............8R-13
WASHER PUMP MOTOR - EXPORT -
REMOVAL, HEADLAMP................8R-12
WASHER PUMP MOTOR -
INSTALLATION, FRONT.................8R-8
WASHER PUMP MOTOR -
INSTALLATION, REAR.................8R-14
WASHER PUMP MOTOR - REMOVAL,
FRONT..............................8R-8
WASHER PUMP MOTOR - REMOVAL,
REAR..............................8R-13
WASHER RESERVOIR - INSTALLATION . . . 8R-17
WASHER RESERVOIR - REMOVAL.......8R-16
WASHER SYSTEM - DIAGNOSIS AND
TESTING............................8R-4
WASHERS - EXPORT - DESCRIPTION,
HEADLAMP.........................8R-10
WASHERS - EXPORT - DIAGNOSIS AND
TESTING, HEADLAMP.................8R-10
WASHERS - EXPORT - INSTALLATION,
HEADLAMP.........................8R-12
WASHERS - EXPORT - OPERATION,
HEADLAMP.........................8R-10
WASHERS - EXPORT - REMOVAL,
HEADLAMP.........................8R-12
WATER CHANNEL - INSTALLATION......23-118
WATER CHANNEL - REMOVAL.........23-118
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-2
WATER PUMP - 2.4L - CLEANING........7-32
WATER PUMP - 2.4L - DESCRIPTION......7-31
WATER PUMP - 2.4L - INSPECTION.......7-32
WATER PUMP - 2.4L - INSTALLATION.....7-32
WATER PUMP - 2.4L - REMOVAL.........7-31
WATER PUMP - 3.3/3.8L - CLEANING.....7-34
WATER PUMP - 3.3/3.8L - DESCRIPTION . . . 7-33
WATER PUMP - 3.3/3.8L - INSPECTION....7-34
WATER PUMP - 3.3/3.8L -
INSTALLATION........................7-34
WATER PUMP - 3.3/3.8L - REMOVAL......7-33
WATER PUMP INLET TUBE - 2.4L -
DESCRIPTION........................7-35
WATER PUMP INLET TUBE - 2.4L -
INSTALLATION........................7-35
WATER PUMP INLET TUBE - 2.4L -
REMOVAL...........................7-35
WATER PUMP INLET TUBE - 3.3/3.8L -
INSTALLATION........................7-36
WATER PUMP INLET TUBE - 3.3/3.8L -
REMOVAL...........................7-36
WATERSHIELD - INSTALLATION.........23-21
WATERSHIELD - REMOVAL.............23-21
WEAR - STANDARD PROCEDURE,
MEASURING TIMING CHAIN............9-153
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD.....................22-16
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE......................22-16
WEATHERSTRIP - INSTALLATION, FRONT
DOOR............................23-111
WEATHERSTRIP - INSTALLATION, FRONT
DOOR GLASS RUN..................23-110
WEATHERSTRIP - INSTALLATION,
SLIDING DOOR.....................23-112
WEATHERSTRIP - REMOVAL, FRONT
DOOR............................23-111
WEATHERSTRIP - REMOVAL, FRONT
DOOR GLASS RUN..................23-110
WEATHERSTRIP - REMOVAL, SLIDING
DOOR............................23-112WELD LOCATIONS - SPECIFICATIONS . . . 23-161
WHEEL - DESCRIPTION...............22-18
WHEEL - INSPECTION, TONE............5-82
WHEEL - INSTALLATION, STEERING......19-24
WHEEL - REMOVAL, STEERING.........19-23
WHEEL ALIGNMENT - DESCRIPTION......2-46
WHEEL ALIGNMENT - STANDARD
PROCEDURE.........................2-51
WHEEL ALIGNMENT, SPECIFICATIONS.....2-55
WHEEL ASSEMBLY (ALUMINUM WHEEL)
- INSTALLATION, TIRE.................22-8
WHEEL ASSEMBLY (ALUMINUM WHEEL)
- REMOVAL, TIRE.....................22-7
WHEEL ASSEMBLY (STEEL WHEEL) -
INSTALLATION, TIRE...................22-8
WHEEL ASSEMBLY (STEEL WHEEL) -
REMOVAL, TIRE......................22-8
WHEEL BALANCE - STANDARD
PROCEDURE, TIRE....................22-5
WHEEL CARE - CLEANING, ALUMINUM . . . 22-18
WHEEL COVER - DESCRIPTION.........22-19
WHEEL COVER - INSTALLATION.........22-19
WHEEL COVER - REMOVAL............22-19
WHEEL CYLINDERS - INSPECTION........5-57
WHEEL CYLINDERS - INSTALLATION......5-57
WHEEL CYLINDERS - REMOVAL..........5-57
WHEEL INSPECTION - DIAGNOSIS AND
TESTING...........................22-18
WHEEL MATCH MOUNTING - STANDARD
PROCEDURE, TIRE....................22-7
WHEEL MOUNTING STUDS - FRONT -
INSTALLATION.......................22-21
WHEEL MOUNTING STUDS - FRONT -
REMOVAL..........................22-20
WHEEL MOUNTING STUDS - REAR -
INSTALLATION.......................22-22
WHEEL MOUNTING STUDS - REAR -
REMOVAL..........................22-21
WHEEL ROTATION - STANDARD
PROCEDURE, TIRE....................22-7
WHEEL RUNOUT, SPECIFICATIONS -
TONE...............................5-79
WHEEL, SPECIFICATIONS..............22-19
WHEEL SPEED SENSOR - AWD -
INSTALLATION, REAR..................5-80
WHEEL SPEED SENSOR - AWD -
REMOVAL, REAR......................5-80
WHEEL SPEED SENSOR - FWD -
INSTALLATION, REAR..................5-81
WHEEL SPEED SENSOR - FWD -
REMOVAL, REAR......................5-81
WHEEL SPEED SENSOR -
INSTALLATION, FRONT.................5-80
WHEEL SPEED SENSOR - REMOVAL,
FRONT..............................5-79
WHEEL SPEED SENSOR AIR GAP,
SPECIFICATIONS......................5-79
WHEEL VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-1
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT................23-54
WHEELHOUSE SPLASH SHIELD -
REMOVAL, FRONT....................23-54
WIND DEFLECTOR - INSTALLATION.....23-118
WIND DEFLECTOR - REMOVAL.........23-118
WIND NOISE - DIAGNOSIS AND TESTING . . 23-3
WINDOW - INSTALLATION, QUARTER . . . 23-108
WINDOW - REMOVAL, QUARTER.......23-108
WINDOW CRANK - INSTALLATION.......23-21
WINDOW CRANK - REMOVAL...........23-21
WINDOW DEFOGGER SWITCH -
DESCRIPTION, REAR..................8G-2
WINDOW DEFOGGER SWITCH -
OPERATION, REAR....................8G-2
WINDOW MOTOR - DIAGNOSIS AND
TESTING, VENT......................8N-63
WINDOW MOTOR - INSTALLATION, VENT . 8N-64WINDOW MOTOR - REMOVAL..........8N-64
WINDOW MOTOR - REMOVAL, VENT.....8N-63
WINDOW REGULATOR - MANUAL -
INSTALLATION.......................23-23
WINDOW REGULATOR - MANUAL -
REMOVAL..........................23-23
WINDOW REGULATOR - POWER -
INSTALLATION.......................23-22
WINDOW REGULATOR - POWER -
REMOVAL..........................23-22
WINDOW SWITCH - DIAGNOSIS AND
TESTING...........................8N-64
WINDOW SWITCH - INSTALLATION......8N-65
WINDOW SWITCH - REMOVAL..........8N-65
WINDOWS - DESCRIPTION, POWER.....8N-62
WINDOWS - DIAGNOSIS AND TESTING,
POWER............................8N-62
WINDOWS - OPERATION, POWER.......8N-62
WINDSHIELD - DESCRIPTION..........23-105
WINDSHIELD SAFETY PRECAUTIONS,
WARNING.........................23-105
WIPER ARM - INSTALLATION, REAR.....8R-14
WIPER ARM - REMOVAL, REAR.........8R-14
WIPER ARM ALIGNMENT - STANDARD
PROCEDURE, FRONT..................8R-8
WIPER ARMS - INSTALLATION, FRONT....8R-9
WIPER ARMS - REMOVAL, FRONT........8R-9
WIPER BLADES - CLEANING...........8R-17
WIPER BLADES - INSTALLATION........8R-17
WIPER BLADES - REMOVAL............8R-17
WIPER LINKAGE - INSTALLATION.......8R-18
WIPER LINKAGE - REMOVAL...........8R-17
WIPER MODULE - INSTALLATION.......8R-18
WIPER MODULE - REMOVAL...........8R-18
WIPER MOTOR - INSTALLATION, FRONT . . . 8R-9
WIPER MOTOR - INSTALLATION, REAR . . . 8R-15
WIPER MOTOR - REMOVAL, FRONT......8R-9
WIPER MOTOR - REMOVAL, REAR......8R-14
WIPER SYSTEM - DIAGNOSIS AND
TESTING, FRONT.....................8R-2
WIPER SYSTEM - DIAGNOSIS AND
TESTING, REAR......................8R-4
WIPERS/WASHERS - DESCRIPTION.......8R-1
WIPERS/WASHERS - OPERATION........8R-2
WIPER/WASHER SWITCH -
DESCRIPTION, REAR.................8R-15
WIPER/WASHER SWITCH - DIAGNOSIS
AND TESTING, FRONT.................8R-2
WIPER/WASHER SWITCH - OPERATION,
REAR..............................8R-15
WIRE SPLICING - STANDARD
PROCEDURE.....................8W-01-15
WIRING - INSTALLATION,
SUPPLEMENTAL DIESEL HEATER.......24-112
WIRING - REMOVAL, SUPPLEMENTAL
DIESEL HEATER.....................24-112
WIRING DIAGRAMS - DESCRIPTION,
HOW TO USE .....................8W-01-1
WIRING HARNESS - DESCRIPTION......8N-35
WIRING HARNESS - DIAGNOSIS AND
TESTING.........................8W-01-7
WIRING HARNESS - INSTALLATION......8N-36
WIRING HARNESS - OPERATION........8N-35
WIRING HARNESS - REMOVAL.........8N-35
WIRING/TERMINAL, SPECIAL TOOLS . . 8W-01-10
WORN THREADS - STANDARD
PROCEDURE, REPAIR OF DAMAGED
OR
.............................9-10,9-86
ZONE - DESCRIPTION, DUAL
............24-1
ZONE - DESCRIPTION, MANUAL THREE
....24-1
ZONE - DESCRIPTION, SINGLE
...........24-1
ZONE - OPERATION, DUAL
..............24-3
ZONE - OPERATION, MANUAL THREE
.....24-3
ZONE ATC - OPERATION, THREE
.........24-3
ZONE ATC - OPERATION, TWO
.........24-106
36 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com