2003 CHRYSLER CARAVAN fuse

OPERATION
The rear blower motor will operate whenever the
ignition switch is in the On position, the heater-A/C
control power is turned on, and the rear heater-A/C
system control switch on the front heater-A/C control
is not in the Off position. The blower motor can only
be turned off by turning off the rear system at the
front heater-A/C control. The blower motor receives
battery current whenever the rear blower motor
relay is energized. The rear blower motor relay out-
put circuit is protected by a fuse in the Intelligent
Power Module (IPM) located in the engine compart-
ment near the battery. In the MTC system, the
blower motor speed is controlled by regulating the
path to ground through the blower control switch and
the blower motor resistor. In the ATC system, the
blower motor speed is controlled by an electronic
blower power module, which uses a pulse width mod-
ulated input from the ATC module and feedback from
the blower motor to regulate the blower motor
ground path it provides. The blower motor and wheel
are used to control the velocity of air moving through
the rear heater-A/C unit housing. The blower motor
controls the velocity of the air flowing through the
rear heater-A/C housing by spinning the blower
wheel within the housing at the selected speed or, in
the ATC system, at the selected or programmed
speed.
DIAGNOSIS AND TESTING - BLOWER MOTOR
BLOWER MOTOR INOPERATIVE
(1) Check the fuse (Fuse 12 - 25 ampere) in the
Intelligent Power Module (IPM). If OK, go to Step 2.
If not OK, repair the shorted circuit or component as
required and replace the faulty fuse.
(2) Turn the ignition switch to the On position. Be
certain that the rear heater-A/C control power is
turned on. Check for battery voltage at the fuse
(Fuse 12 - 25 ampere) in the IPM. If OK, go to Step
3. If not OK, proceed to diagnosis of the rear blower
motor relay. (Refer to 24 - HEATING & AIR CONDI-
TIONING/CONTROLS - REAR/BLOWER MOTOR
RELAY - DIAGNOSIS AND TESTING).(3) Turn the ignition switch to the Off position.
Disconnect and isolate the battery negative cable.
Disconnect the rear HVAC wire harness connector for
the rear blower motor resistor (Manual Temperature
Control) or the rear blower power module (Automatic
Temperature Control) from the resistor or module
connector receptacle. Reconnect the battery negative
cable. Turn the ignition switch to the On position. Be
certain that the rear heater-A/C control power is
turned on. Check for battery voltage at the fused
rear blower motor relay output circuit cavity of the
rear HVAC wire harness connector for the rear
blower motor resistor (MTC) or the rear blower
power module (ATC). If OK, go to Step 4. If not OK,
repair the open fused front blower motor relay output
circuit to the IPM as required.
(4) Turn the ignition switch to the Off position.
Disconnect and isolate the battery negative cable.
Disconnect the rear blower motor pigtail wire connec-
tor from the take out and connector of the rear
HVAC wire harness (MTC) or the connector recepta-
cle of the rear blower power module (ATC). Use
jumper wires to connect a battery and ground feeds
to the blower motor pigtail wire connector. The
blower motor should operate. If OK with MTC, pro-
ceed to diagnosis of the rear blower motor resistor.
(Refer to 24 - HEATING & AIR CONDITIONING/
CONTROLS - REAR/BLOWER MOTOR RESISTOR -
DIAGNOSIS AND TESTING). If OK with ATC, use a
DRBIII scan tool to diagnose the rear blower power
module. Refer to the appropriate diagnostic informa-
tion. If not OK with MTC or ATC, replace the faulty
rear blower motor.
BLOWER MOTOR NOISE OR VIBRATION
Refer to the Blower Motor Noise/Vibration Diagno-
sis chart (Fig. 4).
24 - 54 DISTRIBUTION - REARRS
BLOWER MOTOR (Continued)
ProCarManuals.com

FRONT SUSPENSION, SPECIAL TOOLS.....2-3
FRONT WASHER PUMP MOTOR -
INSTALLATION.......................8R-8
FRONT WASHER PUMP MOTOR -
REMOVAL...........................8R-8
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-80
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-79
FRONT WHEELHOUSE SPLASH SHIELD -
INSTALLATION.......................23-54
FRONT WHEELHOUSE SPLASH SHIELD -
REMOVAL..........................23-54
FRONT WIPER ARM ALIGNMENT -
STANDARD PROCEDURE...............8R-8
FRONT WIPER ARMS - INSTALLATION....8R-9
FRONT WIPER ARMS - REMOVAL........8R-9
FRONT WIPER MOTOR - INSTALLATION . . . 8R-9
FRONT WIPER MOTOR - REMOVAL.......8R-9
FRONT WIPER SYSTEM - DIAGNOSIS
AND TESTING........................8R-2
FRONT WIPER/WASHER SWITCH -
DIAGNOSIS AND TESTING..............8R-2
FRONT/QUAD SEAT CUSHION -
INSTALLATION.......................23-92
FRONT/QUAD SEAT CUSHION -
REMOVAL..........................23-92
FRONT-WHEEL-DRIVE - INSTALLATION....2-36
FRONT-WHEEL-DRIVE - REMOVAL........2-35
FUEL CORRECTION OR ADAPTIVE
MEMORIES, OPERATION...............14-20
FUEL DELIVERY SYSTEM - DIAGNOSIS
AND TESTING........................14-2
FUEL DOSING PUMP - DESCRIPTION....24-108
FUEL DOSING PUMP - INSTALLATION . . . 24-108
FUEL DOSING PUMP - OPERATION.....24-108
FUEL DOSING PUMP - REMOVAL.......24-108
FUEL ENGINE OIL - DESCRIPTION,
FLEXIBLE.............................0-3
FUEL FILL DOOR - INSTALLATION.......23-51
FUEL FILL DOOR - REMOVAL...........23-51
FUEL FILL DOOR BLOCKER LATCH -
INSTALLATION.......................23-52
FUEL FILL DOOR BLOCKER LATCH -
REMOVAL..........................23-52
FUEL FILL DOOR BLOCKER LATCH
STRIKER - INSTALLATION..............23-52
FUEL FILL DOOR BLOCKER LATCH
STRIKER - REMOVAL.................23-52
FUEL FILL DOOR BLOCKER LOCKOUT
LINK - INSTALLATION.................23-53
FUEL FILL DOOR BLOCKER LOCKOUT
LINK - REMOVAL.....................23-52
FUEL FILLER CAP - DESCRIPTION.......25-12
FUEL FILLER CAP - OPERATION.........25-12
FUEL FILTER - INSTALLATION............14-4
FUEL FILTER - REMOVAL...............14-4
FUEL INJECTOR - DESCRIPTION.........14-26
FUEL INJECTOR - OPERATION..........14-26
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION........................14-4
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION........................14-5
FUEL LEVEL SENDING UNIT / SENSOR -
OPERATION..........................14-5
FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL...........................14-5
FUEL LINE - INSTALLATION...........24-110
FUEL LINE - REMOVAL...............24-109
FUEL LINES/HOSES AND CLAMPS -
DESCRIPTION........................14-6
FUEL PRESSURE REGULATOR -
INSTALLATION........................14-7
FUEL PRESSURE REGULATOR -
OPERATION..........................14-7
FUEL PRESSURE REGULATOR -
REMOVAL...........................14-7
FUEL PUMP - DESCRIPTION.............14-7
FUEL PUMP - OPERATION..............14-7
FUEL PUMP MODULE - DESCRIPTION.....14-8
FUEL PUMP MODULE - INSTALLATION....14-9
FUEL PUMP MODULE - OPERATION.......14-8
FUEL PUMP MODULE - REMOVAL
........14-8
FUEL PUMP RELAY - DESCRIPTION
......14-28
FUEL PUMP RELAY - OPERATION
........14-28
FUEL REQUIREMENTS - DESCRIPTION
......0-4
FUEL REQUIREMENTS - DIESEL ENGINE
- DESCRIPTION
........................0-6FUEL, SPECIAL TOOLS............14-23,14-3
FUEL SYSTEM PRESSURE RELEASE
PROCEDURE - STANDARD
PROCEDURE.........................14-2
FUEL SYSTEM PRESSURE,
SPECIFICATIONS......................14-3
FUEL TANK - DESCRIPTION............14-10
FUEL TANK - INSTALLATION............14-11
FUEL TANK - OPERATION..............14-10
FUEL TANK - REMOVAL...............14-11
FUEL TANK - STANDARD PROCEDURE,
DRAINING...........................14-2
FUEL TANK FILLER TUBE -
INSTALLATION.......................14-12
FUEL TANK FILLER TUBE - REMOVAL....14-12
FULL OPEN SWITCH - DESCRIPTION....8N-12,
8N-31
FULL OPEN SWITCH - INSTALLATION....8N-13
FULL OPEN SWITCH - OPERATION . 8N-12,8N-31
FULL OPEN SWITCH - REMOVAL........8N-13
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD...........8W-97-4
FUSE - INSTALLATION, IOD..........8W-97-5
FUSE - OPERATION, IOD.............8W-97-5
FUSE - REMOVAL, IOD..............8W-97-5
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON......8W-01-10
FWD - INSTALLATION..............2-41,2-44
FWD - INSTALLATION, REAR WHEEL
SPEED SENSOR.......................5-81
FWD - REMOVAL..................2-40,2-44
FWD - REMOVAL, REAR WHEEL SPEED
SENSOR............................5-81
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL . 9-10,9-86
GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH AIR............24-17
GAP AND FLUSH MEASUREMENTS -
SPECIFICATIONS....................23-121
GAP, SPECIFICATIONS - WHEEL SPEED
SENSOR AIR.........................5-79
GAS - INSTALLATION, MODULAR
CLUTCH ASSY - 2.4L..................6-11
GAS - REMOVAL, MODULAR CLUTCH
ASSY - 2.4L..........................6-11
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD..................9-24,9-99
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE....9-11,9-85
GASKETS AND SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE.......9-11,9-84
GEAR - DESCRIPTION.................19-26
GEAR - INSTALLATION, LHD............19-32
GEAR - INSTALLATION, RHD............19-33
GEAR & LINK ROD - DESCRIPTION, LIFT . 8N-16
GEAR & LINK ROD - INSTALLATION,
LIFT...............................8N-16
GEAR & LINK ROD - OPERATION, LIFT . . . 8N-16
GEAR & LINK ROD - REMOVAL, LIFT.....8N-16
GEAR - OPERATION...................19-27
GEAR - REMOVAL, LHD...............19-27
GEAR - REMOVAL, RHD...............19-31
GEAR END PLAY - ADJUSTMENT,
DIFFERENTIAL SIDE..................21-70
GEAR SHIFT CABLE - INSTALLATION....21-205
GEAR SHIFT CABLE - REMOVAL........21-204
GEAR SHIFT LEVER - INSTALLATION.....19-21
GEAR SHIFT LEVER - REMOVAL.........19-21
GEAR, SPECIAL TOOLS - POWER
STEERING..........................19-34
GEARSHIFT BOOT - INSTALLATION......21-73
GEARSHIFT BOOT - REMOVAL..........21-72
GEARSHIFT CABLE - CROSSOVER -
INSTALLATION.......................21-76
GEARSHIFT CABLE - CROSSOVER -
REMOVAL..........................21-73
GEARSHIFT CABLE - SELECTOR -
INSTALLATION.......................21-84
GEARSHIFT CABLE - SELECTOR -
REMOVAL..........................21-81
GEARSHIFT CABLE ADJUSTMENT,
ADJUSTMENTS
.....................21-206
GEARSHIFT KNOB - INSTALLATION
......21-87
GEARSHIFT KNOB - REMOVAL
..........21-87
GEARSHIFT MECHANISM -
INSTALLATION
.......................21-89
GEARSHIFT MECHANISM - REMOVAL
....21-87GEARTRAIN - DESCRIPTION,
PLANETARY........................21-232
GEARTRAIN - OPERATION, PLANETARY . . 21-232
GENERAL - WARNINGS.............8W-01-7
GENERAL DIAGNOSIS - DIAGNOSIS AND
TESTING, 41TE TRANSAXLE...........21-119
GENERATOR - DESCRIPTION...........8F-23
GENERATOR - OPERATION.............8F-23
GENERATOR DECOUPLER PULLEY -
DESCRIPTION.......................8F-25
GENERATOR DECOUPLER PULLEY -
DIAGNOSIS AND TESTING..............8F-25
GENERATOR DECOUPLER PULLEY -
INSTALLATION.......................8F-26
GENERATOR DECOUPLER PULLEY -
OPERATION.........................8F-25
GENERATOR DECOUPLER PULLEY -
REMOVAL..........................8F-26
GENERATOR, SPECIFICATIONS..........8F-22
GLASS - DESCRIPTION, HEATED.........8G-1
GLASS - INSTALLATION, DOOR.........23-17
GLASS - INSTALLATION, REAR DOOR . . . 23-108
GLASS - INSTALLATION, SIDE VIEW
MIRROR...........................23-58
GLASS - INSTALLATION, SLIDING DOOR . 23-107
GLASS - OPERATION, HEATED...........8G-1
GLASS - REMOVAL, DOOR.............23-17
GLASS - REMOVAL, REAR DOOR.......23-108
GLASS - REMOVAL, SIDE VIEW MIRROR . . 23-58
GLASS - REMOVAL, SLIDING DOOR.....23-107
GLASS INTEGRAL ANTENNA - EXPORT -
DESCRIPTION, QUARTER...............8A-9
GLASS INTEGRAL ANTENNA - EXPORT -
DIAGNOSIS AND TESTING, QUARTER.....8A-9
GLASS INTEGRAL ANTENNA - EXPORT -
OPERATION, QUARTER.................8A-9
GLASS PANEL - INSTALLATION........23-117
GLASS PANEL - REMOVAL............23-117
GLASS PANEL ADJUSTMENT,
ADJUSTMENTS - SUNROOF...........23-117
GLASS RUN WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-110
GLASS RUN WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-110
GLOVE BOX - INSTALLATION...........23-63
GLOVE BOX - REMOVAL...............23-63
GLOVE BOX LAMP SWITCH -
INSTALLATION.......................8L-26
GLOVE BOX LAMP SWITCH - REMOVAL . . 8L-26
GLOVE BOX LATCH - INSTALLATION.....23-63
GLOVE BOX LATCH - REMOVAL.........23-63
GLOVE BOX LATCH STRIKER -
INSTALLATION.......................23-64
GLOVE BOX LATCH STRIKER - REMOVAL . 23-64
GRID LINE AND TERMINAL REPAIR -
STANDARD PROCEDURE...............8G-3
GRID LINE REPAIR REAR - STANDARD
PROCEDURE.........................8G-2
GRILLE - INSTALLATION, COWL.........23-50
GRILLE - REMOVAL, COWL............23-49
GRILLE OPENING REINFORCEMENT -
INSTALLATION
.......................23-53
GRILLE OPENING REINFORCEMENT -
REMOVAL
..........................23-53
GROCERY BAG RETAINER -
INSTALLATION, PLASTIC
..............23-103
GROCERY BAG RETAINER - REMOVAL,
PLASTIC
..........................23-103
GROMMET REPLACEMENT - STANDARD
PROCEDURE, PUSH-PIN
...............8N-28
GROUND - OPERATION, PCM
...........8E-15
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO
..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR
..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO
.............................8W-01-10
GUIDE - INSTALLATION, UNDER SEAT
STORAGE BIN
......................23-104
GUIDE - REMOVAL, UNDER SEAT
STORAGE BIN
......................23-104
GUIDE PIN BUSHINGS (DISC/DISC
BRAKES) - ASSEMBLY, CALIPER
..........5-25
GUIDE PIN BUSHINGS (DISC/DISC
BRAKES) - DISASSEMBLY, CALIPER
.......5-24
14 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

INPUT - OPERATION, DATA BUS
COMMUNICATION RECEIVE - PCM.......8E-15
INPUT - OPERATION, IGNITION SENSE -
PCM...............................8E-15
INPUT - OPERATION, SENSOR RETURN -
PCM...............................8E-15
INPUT - OPERATION, SPEED SENSOR . . . 21-240
INPUT - REMOVAL, SPEED SENSOR.....21-240
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-216
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-208
INPUT FLANGE SEAL - INSTALLATION.....3-45
INPUT FLANGE SEAL - REMOVAL.........3-44
INPUT SHAFT - ASSEMBLY.............21-96
INPUT SHAFT - DESCRIPTION..........21-93
INPUT SHAFT - DISASSEMBLY..........21-93
INPUT SHAFT COVER SEAL -
INSTALLATION.......................21-14
INPUT SHAFT COVER SEAL - REMOVAL . . . 21-13
INPUT SHAFT END SEAL -
INSTALLATION.......................21-16
INPUT SHAFT END SEAL - REMOVAL.....21-15
INPUT SHAFT SEAL - INSTALLATION.....21-18
INPUT SHAFT SEAL - REMOVAL.........21-17
INSIDE HANDLE CABLE - INSTALLATION . . 23-37
INSIDE HANDLE CABLE - REMOVAL......23-37
INSIDE LATCH HANDLE - INSTALLATION . . 23-33
INSIDE LATCH HANDLE - REMOVAL......23-33
INSPECT, INSPECTION...............21-114
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-1
INSTRUMENT CLUSTER - OPERATION.....8J-1
INSTRUMENT PANEL - INSTALLATION,
LOWER............................23-68
INSTRUMENT PANEL - REMOVAL,
LOWER............................23-68
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-9
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-8
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-65
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-64
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-67
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-67
INSTRUMENT PANEL END CAP -
INSTALLATION.......................23-67
INSTRUMENT PANEL END CAP -
REMOVAL..........................23-67
INSTRUMENT PANEL OUTLET -
INSTALLATION.......................24-42
INSTRUMENT PANEL OUTLET -
REMOVAL..........................24-42
INSTRUMENT PANEL TOP COVER -
INSTALLATION.......................23-67
INSTRUMENT PANEL TOP COVER -
REMOVAL..........................23-67
INSTRUMENT PANEL TOP PAD
ASSEMBLY - INSTALLATION............23-70
INSTRUMENT PANEL TOP PAD
ASSEMBLY - REMOVAL................23-70
INTAKE MANIFOLD - DESCRIPTION . . 9-144,9-58
INTAKE MANIFOLD - INSTALLATION,
LOWER............................9-149
INTAKE MANIFOLD - INSTALLATION,
UPPER.............................9-147
INTAKE MANIFOLD - LOWER -
CLEANING..........................9-148
INTAKE MANIFOLD - LOWER -
INSPECTION....................9-148,9-60
INTAKE MANIFOLD - LOWER -
INSTALLATION........................9-60
INTAKE MANIFOLD - LOWER - REMOVAL . . 9-60
INTAKE MANIFOLD - REMOVAL, LOWER . . 9-148
INTAKE MANIFOLD - REMOVAL, UPPER . . . 9-145
INTAKE MANIFOLD - UPPER -
INSPECTION.........................9-59
INTAKE MANIFOLD - UPPER -
INSTALLATION........................9-59
INTAKE MANIFOLD - UPPER - REMOVAL
. . . 9-58
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING
...................9-145,9-58
INTAKE MANIFOLD VACUUM PORT
REPAIR - STANDARD PROCEDURE
.......9-145
INTAKE PIPE - INSTALLATION, AIR
......24-113
INTAKE PIPE - REMOVAL, AIR
.........24-112INTAKE/EXHAUST VALVES & SEATS -
CLEANING......................9-105,9-32
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION...................9-104,9-32
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION........................9-105
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION.......................9-106
INTAKE/EXHAUST VALVES & SEATS -
OPERATION.........................9-104
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL..........................9-105
INTEGRAL ANTENNA - EXPORT -
DESCRIPTION, QUARTER GLASS.........8A-9
INTEGRAL ANTENNA - EXPORT -
DIAGNOSIS AND TESTING, QUARTER
GLASS..............................8A-9
INTEGRAL ANTENNA - EXPORT -
OPERATION, QUARTER GLASS...........8A-9
INTEGRATED POWER MODULE -
DESCRIPTION.....................8W-97-3
INTEGRATED POWER MODULE -
INSTALLATION....................8W-97-4
INTEGRATED POWER MODULE -
OPERATION.......................8W-97-3
INTEGRATED POWER MODULE -
REMOVAL........................8W-97-4
INTERACTIVE SPEED CONTROL (4
SPEED EATX ONLY) - OPERATION........8P-2
INTERFACE (PCI) BUS, OPERATION -
PROGRAMMABLE COMMUNICATIONS....14-21
INTERIOR LAMPS, SPECIFICATIONS......8L-25
INTERLOCK - DESCRIPTION, IGNITION....19-17
INTERLOCK SOLENOID - DESCRIPTION,
SHIFT.............................21-233
INTERLOCK SOLENOID - DIAGNOSIS
AND TESTING, BRAKE/TRANSMISSION
SHIFT.............................21-235
INTERLOCK SOLENOID - INSTALLATION,
SHIFT.............................21-236
INTERLOCK SOLENOID - OPERATION,
SHIFT.............................21-233
INTERLOCK SOLENOID - REMOVAL,
SHIFT.............................21-235
INTERLOCK SWITCH - INSTALLATION,
CLUTCH PEDAL.......................6-14
INTERLOCK SWITCH - REMOVAL,
CLUTCH PEDAL.......................6-13
INTERMEDIATE SHAFT - ASSEMBLY.....21-107
INTERMEDIATE SHAFT - DESCRIPTION . . 21-100
INTERMEDIATE SHAFT - DISASSEMBLY . . 21-100
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-5
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-3,9-76
IOD FUSE - DESCRIPTION...........8W-97-4
IOD FUSE - INSTALLATION...........8W-97-5
IOD FUSE - OPERATION.............8W-97-5
IOD FUSE - REMOVAL..............8W-97-5
JOINT - DESCRIPTION, LOWER BALL......2-10
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - OPERATION, LOWER BALL.......2-10
JOINT MOLDING - INSTALLATION, ROOF . . 23-57
JOINT MOLDING - REMOVAL, ROOF......23-57
JOINT SEAL BOOT - INSTALLATION,
BALL
...............................2-11
JOINT SEAL BOOT - REMOVAL, BALL
.....2-11
JOUNCE BUMPER - DESCRIPTION
........2-35
JOUNCE BUMPER - OPERATION
..........2-35
JUMP STARTING - STANDARD
PROCEDURE
.........................0-15
JUNCTION BLOCK - DESCRIPTION,
NON-ABS
............................5-33
JUNCTION BLOCK - INSTALLATION,
NON-ABS
............................5-33
JUNCTION BLOCK - OPERATION,
NON-ABS
............................5-33
JUNCTION BLOCK - REMOVAL, NON-ABS
. . 5-33
KEY - DESCRIPTION, TRANSPONDER
.....8Q-3
KEY - OPERATION, TRANSPONDER
.......8Q-3
KEY IMMOBILIZER MODULE -
DESCRIPTION, SENTRY
................8E-18
KEY IMMOBILIZER MODULE -
INSTALLATION, SENTRY
...............8E-19KEY IMMOBILIZER MODULE -
OPERATION, SENTRY.................8E-18
KEY IMMOBILIZER MODULE - REMOVAL,
SENTRY............................8E-18
KEY IMMOBILIZER SYSTEM -
DIAGNOSIS AND TESTING, SENTRY.......8Q-3
KEYLESS ENTRY MODULE -
DESCRIPTION, REMOTE...............8N-43
KEYLESS ENTRY MODULE - DIAGNOSIS
AND TESTING, REMOTE...............8N-43
KEYLESS ENTRY MODULE -
INSTALLATION, REMOTE..............8N-44
KEYLESS ENTRY MODULE - OPERATION,
REMOTE...........................8N-43
KEYLESS ENTRY MODULE - REMOVAL,
REMOTE...........................8N-44
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING.............8N-42
KEY/LOCK CYLINDER - DESCRIPTION....19-20
KEY/LOCK CYLINDER - INSTALLATION....19-20
KEY/LOCK CYLINDER - OPERATION......19-20
KEY/LOCK CYLINDER - REMOVAL.......19-20
KNOB - INSTALLATION, GEARSHIFT......21-87
KNOB - INSTALLATION, SEAT BELT
HEIGHT ADJUSTER...................8O-13
KNOB - REMOVAL, GEARSHIFT..........21-87
KNOB - REMOVAL, SEAT BELT HEIGHT
ADJUSTER.........................8O-13
KNOCK SENSOR - DESCRIPTION..........8I-8
KNOCK SENSOR - OPERATION...........8I-8
KNUCKLE - DESCRIPTION.................2-6
KNUCKLE - INSPECTION, STEERING........2-9
KNUCKLE - INSTALLATION, STEERING......2-9
KNUCKLE - OPERATION.................2-7
KNUCKLE - REMOVAL, STEERING.........2-7
LABEL - DESCRIPTION, E-MARK......Intro.-11
LABEL - DESCRIPTION, VECI.........Intro.-11
LABEL - DESCRIPTION, VEHICLE
EMISSION CONTROL INFORMATION.......25-1
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION....................Intro.-11
LAMP - DESCRIPTION, VTSS/SKIS
INDICATOR..........................8Q-5
LAMP - DIAGNOSIS AND TESTING,
FRONT FOG..........................8L-7
LAMP - EXPORT - DESCRIPTION, REAR
FOG ...............................8L-22
LAMP - EXPORT - INSTALLATION,
FRONT FOG..........................8L-9
LAMP - EXPORT - INSTALLATION,
FRONT POSITION....................8L-10
LAMP - EXPORT - INSTALLATION,
PARK/TURN SIGNAL..................8L-22
LAMP - EXPORT - INSTALLATION,
REPEATER..........................8L-22
LAMP - EXPORT - INSTALLATION, TAIL . . . 8L-23
LAMP - EXPORT - REMOVAL, FRONT
FOG ................................8L-9
LAMP - EXPORT - REMOVAL, FRONT
POSITION..........................8L-10
LAMP - EXPORT - REMOVAL,
PARK/TURN SIGNAL..................8L-22
LAMP - EXPORT - REMOVAL, REPEATER . . 8L-22
LAMP - EXPORT - REMOVAL, TAIL.......8L-23
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - INSTALLATION, COURTESY......8L-26
LAMP - INSTALLATION, DOME/CARGO....8L-26
LAMP - INSTALLATION, FRONT FOG.......8L-9
LAMP - INSTALLATION, LICENSE........8L-20
LAMP - INSTALLATION, LIFTGATE.......8L-27
LAMP - INSTALLATION, PARK/TURN
SIGNAL............................8L-21
LAMP - INSTALLATION, READING........8L-28
LAMP - INSTALLATION, TAIL...........8L-22
LAMP - INSTALLATION, VANITY.........8L-28
LAMP - OPERATION, VTSS/SKIS
INDICATOR..........................8Q-5
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - REMOVAL, COURTESY..........8L-26
LAMP - REMOVAL, DOME/CARGO.......8L-26
LAMP - REMOVAL, FRONT FOG..........8L-9
LAMP - REMOVAL, LICENSE
............8L-20
LAMP - REMOVAL, LIFTGATE
...........8L-27
LAMP - REMOVAL, PARK/TURN SIGNAL
. . 8L-21
LAMP - REMOVAL, READING
...........8L-27
LAMP - REMOVAL, TAIL
...............8L-22
RSINDEX17
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

LIFTGATE MOTOR - OPERATION.........8N-15
LIFTGATE MOTOR - REMOVAL..........8N-15
LIFTGATE SIDE - INSTALLATION.........23-43
LIFTGATE SIDE - REMOVAL............23-43
LIFTGATE SILL PLATE - INSTALLATION . . . 23-77
LIFTGATE SILL PLATE - REMOVAL.......23-77
LIFTGATE SPOILER - INSTALLATION......23-41
LIFTGATE SPOILER - REMOVAL.........23-41
LIFTGATE SYSTEM - DESCRIPTION,
POWER.............................8N-2
LIFTGATE SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LIFTGATE SYSTEM - OPERATION,
POWER.............................8N-3
LIMITS - DESCRIPTION, HIGH AND LOW . . . 25-8
LINE - INSTALLATION, DISCHARGE......24-69
LINE - INSTALLATION, FUEL...........24-110
LINE - INSTALLATION, LIQUID..........24-82
LINE - INSTALLATION, SUCTION . . . 24-102,24-91
LINE - REMOVAL, DISCHARGE..........24-68
LINE - REMOVAL, FUEL...............24-109
LINE - REMOVAL, LIQUID..............24-80
LINE - REMOVAL, SUCTION......24-101,24-90
LINE AND TERMINAL REPAIR -
STANDARD PROCEDURE, GRID..........8G-3
LINE EXTENSION - INSTALLATION,
EVAPORATOR.......................24-96
LINE EXTENSION - REMOVAL,
EVAPORATOR.......................24-95
LINE REPAIR REAR - STANDARD
PROCEDURE, GRID....................8G-2
LINES - DESCRIPTION, OIL COOLER.....9-138
LINES - DESCRIPTION, UNDERBODY....24-103
LINES - INSTALLATION, OIL COOLER.....9-138
LINES - INSTALLATION, REAR AIR
CONDITIONING.....................24-105
LINES - INSTALLATION, REAR HEATER . . 24-105
LINES - INSTALLATION, TRANSMISSION
OIL COOLER.........................7-38
LINES - OPERATION, OIL COOLER.......9-138
LINES - OPERATION, UNDERBODY......24-103
LINES - REMOVAL, OIL COOLER........9-138
LINES - REMOVAL, REAR AIR
CONDITIONING.....................24-104
LINES - REMOVAL, REAR HEATER......24-104
LINES - REMOVAL, TRANSMISSION OIL
COOLER.............................7-38
LINES/HOSES AND CLAMPS -
DESCRIPTION, FUEL...................14-6
LINING - INSPECTION, REAR DRUM
BRAKE SHOE.........................5-22
LINK - DESCRIPTION, TRD............21-249
LINK - INSTALLATION, FUEL FILL DOOR
BLOCKER LOCKOUT..................23-53
LINK - OPERATION, TRD..............21-249
LINK - REMOVAL, FUEL FILL DOOR
BLOCKER LOCKOUT..................23-52
LINK CONNECTOR - DESCRIPTION, DATA . . 8E-6
LINK CONNECTOR - OPERATION, DATA....8E-7
LINK ROD - DESCRIPTION, LIFT GEAR . . . 8N-16
LINK ROD - INSTALLATION, LIFT GEAR . . . 8N-16
LINK ROD - OPERATION, LIFT GEAR.....8N-16
LINK ROD - REMOVAL, LIFT GEAR.......8N-16
LINKAGE - INSTALLATION, WIPER.......8R-18
LINKAGE - REMOVAL, WIPER...........8R-17
LIQUID LINE - INSTALLATION...........24-82
LIQUID LINE - REMOVAL
..............24-80
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL
.....8W-01-10
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE
...................8W-91-1
LOCATIONS - DESCRIPTION, FLUID
FILL/CHECK
...........................0-7
LOCATIONS - SPECIFICATIONS, BODY
SEALING
..........................23-127
LOCATIONS - SPECIFICATIONS,
STRUCTURAL ADHESIVE
..............23-153
LOCATIONS - SPECIFICATIONS, WELD
. . . 23-161
LOCK ASSEMBLY - INSTALLATION,
LATCH
.............................23-27
LOCK ASSEMBLY - REMOVAL, LATCH
....23-26
LOCK CYLINDER - INSTALLATION
. . 23-20,23-41
LOCK CYLINDER - REMOVAL
......23-19,23-41
LOCK CYLINDER HOUSING -
INSTALLATION
.......................19-19
LOCK CYLINDER HOUSING - REMOVAL
. . . 19-17LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR.....................8N-41
LOCK MOTOR - INSTALLATION, SLIDING
DOOR.............................8N-44
LOCK MOTOR - REMOVAL, SLIDING
DOOR.............................8N-44
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER..........................8N-40
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR.....................8N-41
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER............8N-40
LOCK SWITCH - INSTALLATION, DOOR . . . 8N-42
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER..........................8N-41
LOCK SWITCH - OPERATION, DOOR
CYLINDER..........................8N-40
LOCK SWITCH - REMOVAL, DOOR.......8N-42
LOCK SWITCH - REMOVAL, DOOR
CYLINDER..........................8N-41
LOCKED ENGINE - STANDARD
PROCEDURE, HYDROSTATIC.........9-10,9-85
LOCK/LATCH - INSTALLATION, UNDER
SEAT STORAGE BIN.................23-104
LOCK/LATCH - REMOVAL, UNDER SEAT
STORAGE BIN......................23-104
LOCKOUT LINK - INSTALLATION, FUEL
FILL DOOR BLOCKER.................23-53
LOCKOUT LINK - REMOVAL, FUEL FILL
DOOR BLOCKER.....................23-52
LOCKS - DESCRIPTION, POWER........8N-38
LOCKS - OPERATION, POWER..........8N-39
LOUVER - INSTALLATION, REAR HVAC . . . 23-79
LOUVER - REMOVAL, REAR HVAC.......23-79
LOW LIMITS - DESCRIPTION, HIGH.......25-8
LOWER - CLEANING, INTAKE MANIFOLD . . 9-148
LOWER - INSPECTION, INTAKE
MANIFOLD......................9-148,9-60
LOWER - INSTALLATION, INTAKE
MANIFOLD...........................9-60
LOWER - INSTALLATION, SHROUD.......19-22
LOWER - REMOVAL, INTAKE MANIFOLD . . . 9-60
LOWER - REMOVAL, SHROUD..........19-21
LOWER BALL JOINT - DESCRIPTION......2-10
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-10
LOWER BALL JOINT - OPERATION........2-10
LOWER CONSOLE - INSTALLATION......23-68
LOWER CONSOLE - REMOVAL..........23-68
LOWER CONTROL ARM - DESCRIPTION . . . 2-12
LOWER CONTROL ARM - INSPECTION.....2-14
LOWER CONTROL ARM - INSTALLATION . . . 2-15
LOWER CONTROL ARM - OPERATION.....2-12
LOWER CONTROL ARM - REMOVAL......2-12
LOWER CONTROL ARM (REAR BUSHING
- HYDRO) - ASSEMBLY.................2-14
LOWER CONTROL ARM (REAR BUSHING
- HYDRO) - DISASSEMBLY..............2-14
LOWER CONTROL ARM (REAR BUSHING
- STANDARD) - ASSEMBLY..............2-14
LOWER CONTROL ARM (REAR BUSHING
- STANDARD) - DISASSEMBLY...........2-13
LOWER DRIVE UNIT - DESCRIPTION.....8N-32
LOWER DRIVE UNIT - INSTALLATION....8N-33
LOWER DRIVE UNIT - OPERATION.......8N-32
LOWER DRIVE UNIT - REMOVAL
........8N-33
LOWER DRIVE UNIT TRACK & RACK -
DESCRIPTION
.......................8N-34
LOWER DRIVE UNIT TRACK & RACK -
INSTALLATION
......................8N-34
LOWER DRIVE UNIT TRACK & RACK -
OPERATION
.........................8N-34
LOWER DRIVE UNIT TRACK & RACK -
REMOVAL
..........................8N-34
LOWER EXTENSION TRIM -
INSTALLATION, A-PILLAR
..............23-73
LOWER EXTENSION TRIM - REMOVAL,
A-PILLAR
...........................23-73
LOWER HINGE - INSTALLATION
.........23-28
LOWER HINGE - REMOVAL
.............23-28
LOWER INSTRUMENT PANEL -
INSTALLATION
.......................23-68
LOWER INSTRUMENT PANEL -
REMOVAL
..........................23-68
LOWER INTAKE MANIFOLD -
INSTALLATION
.......................9-149
LOWER INTAKE MANIFOLD - REMOVAL
. . . 9-148LOWER STEERING COLUMN COVER -
INSTALLATION.......................23-69
LOWER STEERING COLUMN COVER -
REMOVAL..........................23-69
LOWER TRIM - INSTALLATION,
B-PILLAR...........................23-74
LOWER TRIM - REMOVAL, B-PILLAR.....23-73
LUBRICANTS - DESCRIPTION, ENGINE
OIL .................................0-1
LUBRICATION - DESCRIPTION......9-136,9-52
LUBRICATION - OPERATION........9-136,9-52
LUBRICATION - STANDARD PROCEDURE....2-2
LUBRICATION POINTS - DESCRIPTION......0-7
LUBRICATION, SPECIFICATIONS - BODY . . 23-12
LUGGAGE RACK CROSSBAR -
INSTALLATION.......................23-56
LUGGAGE RACK CROSSBAR - REMOVAL . . 23-55
LUGGAGE RACK RISER - INSTALLATION . . 23-55
LUGGAGE RACK RISER - REMOVAL......23-54
LUMBAR SUPPORT - INSTALLATION....23-104
LUMBAR SUPPORT - REMOVAL........23-104
LWB - INSTALLATION, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC..........8O-15
LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC..........8O-15
MACHINING - STANDARD PROCEDURE,
BRAKE ROTOR.......................5-53
MAIN BEARING FITTING - STANDARD
PROCEDURE..........................9-123
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT.......................9-124
MAIN BEARINGS - REMOVAL,
CRANKSHAFT.......................9-124
MAINTENANCE SCHEDULES -
DESCRIPTION.........................0-7
MANAGER - DESCRIPTION, TASK........25-24
MANAGER - OPERATION, TASK.........25-24
MANIFOLD - CLEANING, EXHAUST........9-61
MANIFOLD - DESCRIPTION, INTAKE . . 9-144,9-58
MANIFOLD - INSPECTION, EXHAUST......9-61
MANIFOLD - INSTALLATION, EXHAUST....9-61
MANIFOLD - INSTALLATION, LOWER
INTAKE ............................9-149
MANIFOLD - INSTALLATION, UPPER
INTAKE ............................9-147
MANIFOLD - LEFT - CLEANING,
EXHAUST...........................9-152
MANIFOLD - LEFT - INSPECTION,
EXHAUST...........................9-152
MANIFOLD - LEFT - INSTALLATION,
EXHAUST...........................9-152
MANIFOLD - LEFT - REMOVAL, EXHAUST . 9-152
MANIFOLD - LOWER - CLEANING,
INTAKE ............................9-148
MANIFOLD - LOWER - INSPECTION,
INTAKE ........................9-148,9-60
MANIFOLD - LOWER - INSTALLATION,
INTAKE .............................9-60
MANIFOLD - LOWER - REMOVAL,
INTAKE .............................9-60
MANIFOLD - REMOVAL, EXHAUST........9-61
MANIFOLD - REMOVAL, LOWER INTAKE . . 9-148
MANIFOLD - REMOVAL, UPPER INTAKE . . . 9-145
MANIFOLD - RIGHT - CLEANING,
EXHAUST...........................9-151
MANIFOLD - RIGHT - INSPECTION,
EXHAUST...........................9-151
MANIFOLD - RIGHT - INSTALLATION,
EXHAUST...........................9-151
MANIFOLD - RIGHT - REMOVAL,
EXHAUST...........................9-150
MANIFOLD - UPPER - INSPECTION,
INTAKE .............................9-59
MANIFOLD - UPPER - INSTALLATION,
INTAKE .............................9-59
MANIFOLD - UPPER - REMOVAL, INTAKE . . 9-58
MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE
................9-145,9-58
MANIFOLD STRIPPED THREAD REPAIR -
STANDARD PROCEDURE
...............9-145
MANIFOLD VACUUM PORT REPAIR -
STANDARD PROCEDURE, INTAKE
........9-145
MANUAL - INSTALLATION, WINDOW
REGULATOR
........................23-23
MANUAL - REMOVAL, WINDOW
REGULATOR
........................23-23
RSINDEX19
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

POWER LIFTGATE CONTROL MODULE -
REMOVAL..........................8E-11
POWER LIFTGATE LEARN CYCLE -
STANDARD PROCEDURE...............8N-9
POWER LIFTGATE SYSTEM -
DESCRIPTION........................8N-2
POWER LIFTGATE SYSTEM - DIAGNOSIS
AND TESTING........................8N-4
POWER LIFTGATE SYSTEM - OPERATION . . 8N-3
POWER LOCKS - DESCRIPTION.........8N-38
POWER LOCKS - OPERATION...........8N-39
POWER MIRRORS - DESCRIPTION......8N-45
POWER MIRRORS - DIAGNOSIS AND
TESTING...........................8N-46
POWER MIRRORS - OPERATION........8N-45
POWER MODULE - DESCRIPTION . . 24-25,24-37
POWER MODULE - DESCRIPTION,
INTEGRATED......................8W-97-3
POWER MODULE - INSTALLATION . . 24-26,24-38
POWER MODULE - INSTALLATION,
INTEGRATED......................8W-97-4
POWER MODULE - OPERATION....24-26,24-37
POWER MODULE - OPERATION,
INTEGRATED......................8W-97-3
POWER MODULE - REMOVAL......24-26,24-37
POWER MODULE - REMOVAL,
INTEGRATED......................8W-97-4
POWER OUTLET - DESCRIPTION......8W-97-5
POWER OUTLET - DIAGNOSIS &
TESTING.........................8W-97-6
POWER OUTLET - OPERATION........8W-97-5
POWER SEAT SYSTEM - DIAGNOSIS
AND TESTING.......................8N-52
POWER SEAT SYSTEM - OPERATION.....8N-52
POWER SEAT TRACK - DESCRIPTION,
DRIVER............................8N-58
POWER SEAT TRACK - DESCRIPTION,
PASSENGER........................8N-59
POWER SEAT TRACK - DIAGNOSIS AND
TESTING...........................8N-60
POWER SEAT TRACK - DIAGNOSIS AND
TESTING, DRIVER....................8N-58
POWER SEAT TRACK - INSTALLATION,
DRIVER............................8N-59
POWER SEAT TRACK - INSTALLATION,
PASSENGER........................8N-61
POWER SEAT TRACK - OPERATION,
DRIVER............................8N-58
POWER SEAT TRACK - OPERATION,
PASSENGER........................8N-60
POWER SEAT TRACK - REMOVAL,
DRIVER............................8N-59
POWER SEAT TRACK - REMOVAL,
PASSENGER........................8N-61
POWER SLIDING DOOR SYSTEM -
DESCRIPTION.......................8N-19
POWER SLIDING DOOR SYSTEM -
DIAGNOSIS AND TESTING.............8N-22
POWER SLIDING DOOR SYSTEM -
OPERATION.........................8N-21
POWER STEERING BELT TENSION -
STANDARD PROCEDURE, CHECKING.......7-8
POWER STEERING FASTENER TORQUE,
SPECIFICATIONS......................19-9
POWER STEERING FLUID LEVEL
CHECKING - STANDARD PROCEDURE....19-44
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-34
POWER STEERING PUMP INITIAL
OPERATION - STANDARD PROCEDURE . . . 19-37
POWER STEERING PUMP, SPECIAL
TOOLS.............................19-43
POWER STEERING, SPECIAL TOOLS......19-9
POWER STEERING SYSTEM -
DESCRIPTION........................19-1
POWER STEERING SYSTEM -
OPERATION..........................19-1
POWER STEERING SYSTEM FLOW AND
PRESSURE TEST - DIAGNOSIS AND
TESTING............................19-1
POWER TRANSFER UNIT - DESCRIPTION . . 21-1
POWER TRANSFER UNIT - OPERATION
....21-3
POWER TRANSFER UNIT, SPECIAL
TOOLS - SDP
........................21-8
POWER WINDOWS - DESCRIPTION
......8N-62
POWER WINDOWS - DIAGNOSIS AND
TESTING
...........................8N-62
POWER WINDOWS - OPERATION
........8N-62POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY...................23-1
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY................23-105
PREFERENCE - STANDARD PROCEDURE,
HORN CHIRP........................8N-42
PRELOAD - ADJUSTMENT,
DIFFERENTIAL BEARING..............21-199
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE........................9-11,9-85
PRESSURE - DIAGNOSIS AND TESTING,
CHECKING ENGINE OIL.................9-52
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL.........................9-136
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-26
PRESSURE CAP - OPERATION,
RADIATOR...........................7-27
PRESSURE CAP TESTING - DIAGNOSIS
AND TESTING, COOLING SYSTEM........7-27
PRESSURE FOR HIGH SPEED
OPERATION - STANDARD PROCEDURE,
TIRE...............................22-17
PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION.....................9-83,9-9
PRESSURE MONITORING -
DESCRIPTION, TIRE...................22-9
PRESSURE MONITORING - OPERATION,
TIRE................................22-9
PRESSURE PLATE - 2.5L TD -
INSTALLATION, CLUTCH DISC...........6-12
PRESSURE PLATE - 2.5L TD - REMOVAL,
CLUTCH DISC........................6-11
PRESSURE REGULATOR -
INSTALLATION, FUEL..................14-7
PRESSURE REGULATOR - OPERATION,
FUEL...............................14-7
PRESSURE REGULATOR - REMOVAL,
FUEL...............................14-7
PRESSURE RELEASE PROCEDURE -
STANDARD PROCEDURE, FUEL
SYSTEM............................14-2
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-141
PRESSURE RELIEF VALVE - REMOVAL,
OIL................................9-141
PRESSURE SENSOR - DIAGNOSIS AND
TESTING, TIRE......................22-10
PRESSURE SENSOR RETRAIN -
STANDARD PROCEDURE, TIRE..........22-10
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM............................14-3
PRESSURE SWITCH - DESCRIPTION, OIL . 9-141
PRESSURE SWITCH - INSTALLATION,
OIL ...........................9-141,9-54
PRESSURE SWITCH - OPERATION, OIL . . . 9-141
PRESSURE SWITCH - REMOVAL, OIL....9-141,
9-54
PRESSURE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMPRESSION . . . 9-83,9-9
PRESSURE TEST - DIAGNOSIS AND
TESTING, POWER STEERING SYSTEM
FLOW...............................19-1
PRESSURE TESTS - DIAGNOSIS AND
TESTING, CLUTCH AIR...............21-122
PRESSURE TESTS - DIAGNOSIS AND
TESTING, HYDRAULIC................21-120
PRESSURE TRANSDUCER -
DESCRIPTION, A/C...................24-10
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C...................24-10
PRESSURE TRANSDUCER -
INSTALLATION, A/C...................24-11
PRESSURE TRANSDUCER - OPERATION,
A/C
................................24-10
PRESSURE TRANSDUCER - REMOVAL,
A/C
................................24-10
PRESSURES - STANDARD PROCEDURE,
TIRE INFLATION
.....................22-16
PROBLEM CAUSES - DIAGNOSIS AND
TESTING, COMMON
..................21-30
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER
.......8N-43PROGRAMMABLE COMMUNICATIONS
INTERFACE (PCI) BUS, OPERATION......14-21
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION CENTER................8M-7
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM................8E-2
PROGRAMMING - STANDARD
PROCEDURE, TRANSPONDER...........8Q-4
PROPELLER SHAFT - DESCRIPTION.......3-21
PROPELLER SHAFT - INSTALLATION......3-22
PROPELLER SHAFT - OPERATION........3-21
PROPELLER SHAFT - REMOVAL..........3-21
PROPELLER SHAFT - SPECIFICATIONS.....3-22
PROPORTIONING - DESCRIPTION,
ELECTRONIC VARIABLE BRAKE..........5-75
PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE BRAKE..........5-77
PROPORTIONING VALVE (HEIGHT
SENSING) - DESCRIPTION..............5-48
PROPORTIONING VALVE (HEIGHT
SENSING) - DIAGNOSIS AND TESTING.....5-49
PROPORTIONING VALVE (HEIGHT
SENSING) - INSTALLATION..............5-51
PROPORTIONING VALVE (HEIGHT
SENSING) - OPERATION................5-48
PROPORTIONING VALVE (HEIGHT
SENSING) - REMOVAL.................5-50
PTU FLUID CHANGE - STANDARD
PROCEDURE.........................21-5
PULLEY - DESCRIPTION, GENERATOR
DECOUPLER........................8F-25
PULLEY - DIAGNOSIS AND TESTING,
GENERATOR DECOUPLER..............8F-25
PULLEY - INSTALLATION, GENERATOR
DECOUPLER........................8F-26
PULLEY - INSTALLATION, TIMING BELT
TENSIONER..........................9-69
PULLEY - OPERATION, GENERATOR
DECOUPLER........................8F-25
PULLEY - REMOVAL, GENERATOR
DECOUPLER........................8F-26
PULLEY - REMOVAL, TIMING BELT
TENSIONER..........................9-68
PUMP - 2.4L - CLEANING, WATER........7-32
PUMP - 2.4L - DESCRIPTION, WATER.....7-31
PUMP - 2.4L - INSPECTION, WATER......7-32
PUMP - 2.4L - INSTALLATION, WATER.....7-32
PUMP - 2.4L - REMOVAL, WATER........7-31
PUMP - 3.3/3.8L - CLEANING, WATER.....7-34
PUMP - 3.3/3.8L - DESCRIPTION,
WATER .............................7-33
PUMP - 3.3/3.8L - INSPECTION, WATER . . . 7-34
PUMP - 3.3/3.8L - INSTALLATION,
WATER .............................7-34
PUMP - 3.3/3.8L - REMOVAL, WATER.....7-33
PUMP - ASSEMBLY, OIL...........9-143,9-56
PUMP - ASSEMBLY, OIL..............21-232
PUMP - CLEANING, OIL...........9-142,9-56
PUMP - DESCRIPTION, FUEL............14-7
PUMP - DESCRIPTION, FUEL DOSING . . . 24-108
PUMP - DESCRIPTION, OIL.............9-142
PUMP - DESCRIPTION, OIL............21-230
PUMP - DISASSEMBLY, OIL........9-142,9-55
PUMP - DISASSEMBLY, OIL...........21-230
PUMP - INSPECTION, OIL..........9-142,9-56
PUMP - INSTALLATION, FUEL DOSING . . . 24-108
PUMP - INSTALLATION, LEAK
DETECTION.........................25-13
PUMP - INSTALLATION, OIL........9-144,9-57
PUMP - INSTALLATION, SEAL - OIL.....21-233
PUMP - OPERATION, FUEL..............14-7
PUMP - OPERATION, FUEL DOSING.....24-108
PUMP - OPERATION, OIL.............21-230
PUMP - REMOVAL, FUEL DOSING......24-108
PUMP - REMOVAL, LEAK DETECTION....25-13
PUMP - REMOVAL, OIL............9-142,9-55
PUMP - REMOVAL, SEAL - OIL.........21-232
PUMP (2.4L ENGINE) - INSTALLATION....19-42
PUMP (2.4L ENGINE) - REMOVAL.......19-38
PUMP (2.4L/3.3L/3.8L ENGINE) -
DESCRIPTION.......................19-36
PUMP (2.5L DIESEL) - DESCRIPTION
.....19-36
PUMP (2.5L DIESEL) - INSTALLATION
....19-43
PUMP (2.5L DIESEL) - REMOVAL
........19-40
PUMP (3.3L/3.8L ENGINE) -
INSTALLATION
.......................19-43
PUMP (3.3L/3.8L ENGINE) - REMOVAL
. . . 19-40
24 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

SEATBACK PANEL - INSTALLATION,
FRONT.............................23-92
SEATBACK PANEL - REMOVAL, BENCH . . . 23-98
SEATBACK PANEL - REMOVAL, FRONT....23-91
SEAT/MIRROR MODULE - DESCRIPTION,
MEMORY...........................8E-10
SEAT/MIRROR MODULE - DIAGNOSIS
AND TESTING, MEMORY...............8E-10
SEAT/MIRROR MODULE -
INSTALLATION, MEMORY..............8E-10
SEAT/MIRROR MODULE - OPERATION,
MEMORY...........................8E-10
SEAT/MIRROR MODULE - REMOVAL,
MEMORY...........................8E-10
SEATS - CLEANING, INTAKE/EXHAUST
VALVES ........................9-105,9-32
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES................9-104,9-32
SEATS - INSPECTION, INTAKE/EXHAUST
VALVES ............................9-105
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES....................9-106
SEATS - OPERATION, INTAKE/EXHAUST
VALVES ............................9-104
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES ............................9-105
SEATS - STANDARD PROCEDURE,
REFACING VALVES AND VALVE..........9-104
SECOND ROW - INSTALLATION, BENCH
SEAT RISER........................23-100
SECOND ROW - LEFT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-16
SECOND ROW - LEFT OUTBOARD -
REMOVAL, SEAT BELT & RETRACTOR....8O-16
SECOND ROW - REMOVAL, BENCH SEAT
RISER.............................23-99
SECOND ROW - RIGHT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-14
SECOND ROW - RIGHT OUTBOARD -
REMOVAL, SEAT BELT & RETRACTOR....8O-14
SECOND ROW - RIGHT OUTBOARD
WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-15
SECOND ROW - RIGHT OUTBOARD
WITH REAR HVAC - LWB - REMOVAL,
SEAT BELT & RETRACTOR.............8O-15
SECOND ROW - THREE PASSENGER
BENCH - INSTALLATION, SEAT BELT
BUCKLE............................8O-14
SECOND ROW - THREE PASSENGER
BENCH - REMOVAL, SEAT BELT
BUCKLE............................8O-14
SECOND ROW INBOARD - 50/50 BENCH
- INSTALLATION, SEAT BELT BUCKLE....8O-12
SECOND ROW INBOARD - 50/50 BENCH
- REMOVAL, SEAT BELT BUCKLE........8O-12
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION........8W-01-6
SECURITY - DESCRIPTION, VEHICLE
THEFT
..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT
. . 8Q-1
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT
..............8Q-3
SELECTION, ADJUSTMENTS - OUTPUT
FLANGE SHIM
........................21-7
SELECTOR - INSTALLATION, GEARSHIFT
CABLE
.............................21-84
SELECTOR - REMOVAL, GEARSHIFT
CABLE
.............................21-81
SELF-DIAGNOSTICS - DIAGNOSIS AND
TESTING
............................8J-2
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL
.............14-4
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL
.............14-5
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL
..........................14-5
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL
..........................14-5
SENSE - PCM INPUT - OPERATION,
IGNITION
...........................8E-15
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD)
.................8W-01-8SENSOR - 2.4L - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 2.4L - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 2.4L - REMOVAL, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 3.3/3.8L - DESCRIPTION,
ENGINE COOLANT TEMPERATURE........7-21
SENSOR - 3.3/3.8L - INSTALLATION,
ENGINE COOLANT TEMPERATURE........7-22
SENSOR - 3.3/3.8L - REMOVAL, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - AWD - INSTALLATION, REAR
WHEEL SPEED........................5-80
SENSOR - AWD - REMOVAL, REAR
WHEEL SPEED........................5-80
SENSOR - DESCRIPTION, AMBIENT
TEMP.............................8M-11
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-23
SENSOR - DESCRIPTION, CAMSHAFT
POSITION............................8I-3
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION..........................14-24
SENSOR - DESCRIPTION, ENGINE SPEED . 14-25
SENSOR - DESCRIPTION, EVAPORATOR
TEMPERATURE......................24-22
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT.......................14-4
SENSOR - DESCRIPTION, HEATED SEAT . . 8G-11
SENSOR - DESCRIPTION, INFRARED
TEMPERATURE.................24-23,24-35
SENSOR - DESCRIPTION, INLET AIR
TEMPERATURE......................14-29
SENSOR - DESCRIPTION, KNOCK.........8I-8
SENSOR - DESCRIPTION, MAP..........14-30
SENSOR - DESCRIPTION, O2...........14-31
SENSOR - DESCRIPTION, PINCH........8N-17
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-36
SENSOR - DESCRIPTION,
TRANSMISSION RANGE..............21-248
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-12
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-12
SENSOR - DIAGNOSIS AND TESTING,
TIRE PRESSURE.....................22-10
SENSOR - FWD - INSTALLATION, REAR
WHEEL SPEED........................5-81
SENSOR - FWD - REMOVAL, REAR
WHEEL SPEED........................5-81
SENSOR - INPUT - DESCRIPTION,
SPEED............................21-239
SENSOR - INPUT - INSTALLATION,
SPEED............................21-240
SENSOR - INPUT - OPERATION, SPEED . . 21-240
SENSOR - INPUT - REMOVAL, SPEED . . . 21-240
SENSOR - INSTALLATION, EVAPORATOR
TEMPERATURE......................24-23
SENSOR - INSTALLATION, FRONT
WHEEL SPEED........................5-80
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - INSTALLATION, PINCH........8N-17
SENSOR - INSTALLATION,
TRANSMISSION RANGE..............21-249
SENSOR - INSTALLATION, VEHICLE
SPEED............................21-115
SENSOR - OPERATION, AMBIENT TEMP . . 8M-11
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-23
SENSOR - OPERATION, CAMSHAFT
POSITION............................8I-3
SENSOR - OPERATION, CRANKSHAFT
POSITION..........................14-24
SENSOR - OPERATION, ENGINE SPEED . . . 14-26
SENSOR - OPERATION, EVAPORATOR
TEMPERATURE......................24-23
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - OPERATION, HEATED SEAT
....8G-12
SENSOR - OPERATION, INFRARED
TEMPERATURE
.................24-24,24-35
SENSOR - OPERATION, INLET AIR
TEMPERATURE
......................14-29
SENSOR - OPERATION, KNOCK
...........8I-8
SENSOR - OPERATION, MAP
...........14-30SENSOR - OPERATION, O2.............14-31
SENSOR - OPERATION, PINCH..........8N-17
SENSOR - OPERATION, THROTTLE
POSITION..........................14-36
SENSOR - OPERATION, TRANSMISSION
RANGE............................21-248
SENSOR - OUTPUT - DESCRIPTION,
SPEED............................21-241
SENSOR - OUTPUT - INSTALLATION,
SPEED............................21-242
SENSOR - OUTPUT - OPERATION, SPEED . 21-241
SENSOR - OUTPUT - REMOVAL, SPEED . . 21-241
SENSOR - REMOVAL, BATTERY
TEMPERATURE......................8F-23
SENSOR - REMOVAL, CRANKSHAFT
POSITION..........................14-25
SENSOR - REMOVAL, EVAPORATOR
TEMPERATURE......................24-23
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-79
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - REMOVAL, PINCH...........8N-17
SENSOR - REMOVAL, TRANSMISSION
RANGE............................21-249
SENSOR - REMOVAL, VEHICLE SPEED . . . 21-115
SENSOR - SPECIFICATIONS, BATTERY
TEMPERATURE......................8F-22
SENSOR - TPM - CAUTION.............22-10
SENSOR - TPM - DESCRIPTION.........22-10
SENSOR - TPM - INSTALLATION..........22-12
SENSOR - TPM - OPERATION...........22-10
SENSOR - TPM - REMOVAL............22-11
SENSOR AIR GAP, SPECIFICATIONS -
WHEEL SPEED........................5-79
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE......8M-12
SENSOR RETRAIN - STANDARD
PROCEDURE, TIRE PRESSURE..........22-10
SENSOR RETURN - PCM INPUT -
OPERATION.........................8E-15
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION.......................8E-18
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION.......................8E-19
SENTRY KEY IMMOBILIZER MODULE -
OPERATION.........................8E-18
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL..........................8E-18
SENTRY KEY IMMOBILIZER SYSTEM -
DIAGNOSIS AND TESTING..............8Q-3
SERVO - DESCRIPTION.................8P-4
SERVO - INSTALLATION................8P-5
SERVO - OPERATION..................8P-4
SERVO - REMOVAL....................8P-5
SET SWITCH - DESCRIPTION, MEMORY . . 8N-55
SET SWITCH - INSTALLATION, MEMORY . . 8N-56
SET SWITCH - OPERATION, MEMORY....8N-56
SET SWITCH - REMOVAL, MEMORY.....8N-56
SETTING - STANDARD PROCEDURE,
PINION FACTOR................8E-15,8E-23
SETTING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-11
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-10
SHAFT - ASSEMBLY, INPUT............21-96
SHAFT - ASSEMBLY, INTERMEDIATE....21-107
SHAFT - ASSEMBLY, ROCKER ARMS.....9-109
SHAFT - DESCRIPTION, INPUT..........21-93
SHAFT - DESCRIPTION, INTERMEDIATE . . 21-100
SHAFT - DESCRIPTION, PROPELLER......3-21
SHAFT - DESCRIPTION, SHIFT FORK....21-113
SHAFT - DIAGNOSIS AND TESTING,
HALF............................3-1,3-13
SHAFT - DISASSEMBLY, INPUT..........21-93
SHAFT - DISASSEMBLY, INTERMEDIATE . . 21-100
SHAFT - DISASSEMBLY, ROCKER ARMS . . 9-109
SHAFT - FRONT - DESCRIPTION, HALF.....3-1
SHAFT - FRONT - INSTALLATION, HALF.....3-4
SHAFT - FRONT - REMOVAL, HALF........3-2
SHAFT - FRONT - SPECIFICATIONS, HALF . . 3-15,
3-6
SHAFT - INSTALLATION, PROPELLER
......3-22
SHAFT - INSTALLATION, ROCKER ARMS
. . 9-110
SHAFT - OPERATION, PROPELLER
........3-21
SHAFT - REAR - DESCRIPTION, HALF
.....3-13
SHAFT - REAR - INSTALLATION, HALF
.....3-14
RSINDEX29
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

SHAFT - REAR - REMOVAL, HALF........3-13
SHAFT - REMOVAL, PROPELLER.........3-21
SHAFT - REMOVAL, ROCKER ARMS......9-109
SHAFT - RHD - INSTALLATION, PEDAL
TORQUE............................5-39
SHAFT - RHD - REMOVAL, PEDAL
TORQUE............................5-39
SHAFT - SPECIFICATIONS, PROPELLER....3-22
SHAFT COVER SEAL - INSTALLATION,
INPUT.............................21-14
SHAFT COVER SEAL - REMOVAL, INPUT . . 21-13
SHAFT END SEAL - INSTALLATION,
INPUT.............................21-16
SHAFT END SEAL - REMOVAL, INPUT....21-15
SHAFT INNER SEAL - INSTALLATION,
HALF..............................21-12
SHAFT INNER SEAL - REMOVAL, HALF . . . 21-12
SHAFT SEAL - INSTALLATION, INPUT.....21-18
SHAFT SEAL - INSTALLATION, OUTER
HALF..............................21-19
SHAFT SEAL - REMOVAL, INPUT........21-17
SHAFT SEAL - REMOVAL, OUTER HALF . . . 21-19
SHAFTS AND CARRIER ASSEMBLY -
DESCRIPTION, BALANCE................9-69
SHAFTS AND CARRIER ASSEMBLY -
INSTALLATION, BALANCE...............9-72
SHAFTS AND CARRIER ASSEMBLY -
OPERATION, BALANCE.................9-69
SHAFTS AND CARRIER ASSEMBLY -
REMOVAL, BALANCE...................9-69
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH................23-54
SHIELD - NO CUP HOLDER -
INSTALLATION, QUAD BUCKET SEAT
SIDE..............................23-96
SHIELD - NO CUP HOLDER - REMOVAL,
QUAD BUCKET SEAT SIDE.............23-96
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH................23-54
SHIELD/CUP HOLDER - INSTALLATION,
QUAD BUCKET SEAT SIDE.............23-95
SHIELD/CUP HOLDER - REMOVAL, QUAD
BUCKET SEAT SIDE...................23-95
SHIELDS - DESCRIPTION, HEAT..........11-6
SHIELDS - INSTALLATION, HEAT.........11-7
SHIELDS - OPERATION, HEAT............11-7
SHIELDS - REMOVAL, HEAT.............11-7
SHIFT CABLE - INSTALLATION, GEAR....21-205
SHIFT CABLE - REMOVAL, GEAR.......21-204
SHIFT COVER - DESCRIPTION.........21-113
SHIFT FORK AND SHAFT - DESCRIPTION . 21-113
SHIFT INTERLOCK SOLENOID -
DESCRIPTION......................21-233
SHIFT INTERLOCK SOLENOID -
DIAGNOSIS AND TESTING, BRAKE/
TRANSMISSION.....................21-235
SHIFT INTERLOCK SOLENOID -
INSTALLATION......................21-236
SHIFT INTERLOCK SOLENOID -
OPERATION........................21-233
SHIFT INTERLOCK SOLENOID -
REMOVAL.........................21-235
SHIFT LEVER - INSTALLATION, GEAR.....19-21
SHIFT LEVER - REMOVAL, GEAR........19-21
SHIM SELECTION, ADJUSTMENTS -
OUTPUT FLANGE......................21-7
SHOCK ABSORBER - DESCRIPTION.......2-36
SHOCK ABSORBER - INSTALLATION......2-38
SHOCK ABSORBER - OPERATION.........2-36
SHOCK ABSORBER - REMOVAL..........2-36
SHOCK ABSORBER (UPPER BUSHING) -
ASSEMBLY..........................2-37
SHOCK ABSORBER (UPPER BUSHING) -
DISASSEMBLY........................2-36
SHOE LINING - INSPECTION, REAR
DRUM BRAKE........................5-22
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-73
SHOES - ADJUSTMENT, REAR DRUM
BRAKE..............................5-23
SHOES - CLEANING, DISC BRAKE....5-16,5-18
SHOES - INSPECTION, DISC BRAKE
. . . 5-16,5-18
SHOES - INSTALLATION, REAR DISC
BRAKE
..............................5-19
SHOES - INSTALLATION, REAR DRUM
BRAKE
..............................5-22
SHOES - PARKING BRAKE -
INSTALLATION
........................5-72
SHOES - PARKING BRAKE - REMOVAL
....5-67SHOES - REMOVAL, REAR DISC BRAKE....5-17
SHOES - REMOVAL, REAR DRUM BRAKE . . 5-19
SHOES (DISC/DISC BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-16
SHOES (DISC/DISC BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-14
SHOES (DISC/DRUM BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-17
SHOES (DISC/DRUM BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-15
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A ..........................8W-01-10
SHROUD - LOWER - INSTALLATION......19-22
SHROUD - LOWER - REMOVAL.........19-21
SHROUD - UPPER - INSTALLATION......19-23
SHROUD - UPPER - REMOVAL..........19-23
SHUT DOWN RELAY - DESCRIPTION,
AUTO...............................8I-3
SHUT DOWN RELAY - OPERATION, AUTO . . . 8I-3
SIDE - INSTALLATION, LIFTGATE........23-43
SIDE - REMOVAL, LIFTGATE............23-43
SIDE COVER - INSTALLATION, FRONT
SEAT CUSHION......................23-93
SIDE COVER - REMOVAL, FRONT SEAT
CUSHION...........................23-93
SIDE GEAR END PLAY - ADJUSTMENT,
DIFFERENTIAL.......................21-70
SIDE IMPACT AIRBAG CONTROL
MODULE - DESCRIPTION..............8O-17
SIDE IMPACT AIRBAG CONTROL
MODULE - INSTALLATION.............8O-17
SIDE IMPACT AIRBAG CONTROL
MODULE - OPERATION................8O-17
SIDE IMPACT AIRBAG CONTROL
MODULE - REMOVAL.................8O-17
SIDE MOLDINGS - INSTALLATION, BODY . . 23-45
SIDE MOLDINGS - REMOVAL, BODY.....23-44
SIDE SHIELD - NO CUP HOLDER -
INSTALLATION, QUAD BUCKET SEAT.....23-96
SIDE SHIELD - NO CUP HOLDER -
REMOVAL, QUAD BUCKET SEAT.........23-96
SIDE SHIELD/CUP HOLDER -
INSTALLATION, QUAD BUCKET SEAT.....23-95
SIDE SHIELD/CUP HOLDER - REMOVAL,
QUAD BUCKET SEAT..................23-95
SIDE VIEW MIRROR - INSTALLATION.....23-57
SIDE VIEW MIRROR - REMOVAL........23-57
SIDE VIEW MIRROR GLASS -
INSTALLATION.......................23-58
SIDE VIEW MIRROR GLASS - REMOVAL . . 23-58
SIDEVIEW MIRROR - REMOVAL.........8N-49
SIGNAL LAMP - EXPORT -
INSTALLATION, PARK/TURN............8L-22
SIGNAL LAMP - EXPORT - REMOVAL,
PARK/TURN.........................8L-22
SIGNAL LAMP - INSTALLATION,
PARK/TURN.........................8L-21
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-21
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-21
SIGNAL SYSTEM - OPERATION, TURN....8L-21
SILL PLATE - INSTALLATION, LIFTGATE . . . 23-77
SILL PLATE - INSTALLATION, SLIDING
DOOR.............................23-80
SILL PLATE - REMOVAL, LIFTGATE.......23-77
SILL PLATE - REMOVAL, SLIDING DOOR . . 23-80
SILL TRIM PLATE - INSTALLATION,
DOOR
.............................23-76
SILL TRIM PLATE - REMOVAL, DOOR
....23-76
SINGLE ZONE - DESCRIPTION
...........24-1
SLAVE CYLINDER - INSTALLATION
........6-11
SLAVE CYLINDER - REMOVAL
...........6-11
SLEEVE - INSTALLATION, HEADREST
.....23-89
SLEEVE - REMOVAL, HEADREST
........23-89
SLIDING DOOR - INSTALLATION
.........23-29
SLIDING DOOR - REMOVAL
............23-29
SLIDING DOOR ADJUSTMENT -
STANDARD PROCEDURE
..............8N-28
SLIDING DOOR ADJUSTMENTS,
ADJUSTMENTS
......................23-30
SLIDING DOOR CONTROL MODULE -
DESCRIPTION
.......................8E-19
SLIDING DOOR CONTROL MODULE -
INSTALLATION
.......................8E-20SLIDING DOOR CONTROL MODULE -
OPERATION.........................8E-19
SLIDING DOOR CONTROL MODULE -
REMOVAL..........................8E-19
SLIDING DOOR GLASS - INSTALLATION . . 23-107
SLIDING DOOR GLASS - REMOVAL.....23-107
SLIDING DOOR LOCK MOTOR -
INSTALLATION......................8N-44
SLIDING DOOR LOCK MOTOR -
REMOVAL..........................8N-44
SLIDING DOOR MOTOR - DESCRIPTION . . 8N-30
SLIDING DOOR MOTOR - INSTALLATION . . 8N-31
SLIDING DOOR MOTOR - OPERATION....8N-30
SLIDING DOOR MOTOR - REMOVAL.....8N-30
SLIDING DOOR SILL PLATE -
INSTALLATION.......................23-80
SLIDING DOOR SILL PLATE - REMOVAL . . 23-80
SLIDING DOOR STOP BUMPER BEZEL -
INSTALLATION.......................23-25
SLIDING DOOR STOP BUMPER BEZEL -
REMOVAL..........................23-25
SLIDING DOOR SYSTEM - DESCRIPTION,
POWER............................8N-19
SLIDING DOOR SYSTEM - DIAGNOSIS
AND TESTING, POWER................8N-22
SLIDING DOOR SYSTEM - OPERATION,
POWER............................8N-21
SLIDING DOOR WEATHERSTRIP -
INSTALLATION......................23-112
SLIDING DOOR WEATHERSTRIP -
REMOVAL.........................23-112
SOCKET - INSTALLATION, STABILIZER....23-32
SOCKET - REMOVAL, STABILIZER.......23-32
SOLENOID - DESCRIPTION, EVAP/PURGE . 25-12
SOLENOID - DESCRIPTION, SHIFT
INTERLOCK........................21-233
SOLENOID - DIAGNOSIS AND TESTING,
BRAKE/TRANSMISSION SHIFT
INTERLOCK........................21-235
SOLENOID - INSTALLATION, EVAP/
PURGE.............................25-12
SOLENOID - INSTALLATION, SHIFT
INTERLOCK........................21-236
SOLENOID - OPERATION, EVAP/PURGE . . . 25-12
SOLENOID - OPERATION, SHIFT
INTERLOCK........................21-233
SOLENOID - REMOVAL, EVAP/PURGE.....25-12
SOLENOID - REMOVAL, SHIFT
INTERLOCK........................21-235
SOLENOID/PRESSURE SWITCH ASSY -
DESCRIPTION......................21-237
SOLENOID/PRESSURE SWITCH ASSY -
INSTALLATION......................21-239
SOLENOID/PRESSURE SWITCH ASSY -
OPERATION........................21-237
SOLENOID/PRESSURE SWITCH ASSY -
REMOVAL.........................21-238
SPARE TIRE (TEMPORARY) -
DESCRIPTION.......................22-14
SPARK PLUG CABLE - DESCRIPTION.....8I-10
SPARK PLUG CABLE RESISTANCE,
SPECIFICATIONS......................8I-2
SPARK PLUG, SPECIFICATIONS...........8I-2
SPEAKER - DIAGNOSIS AND TESTING....8A-14
SPEAKER - INSTALLATION.............8A-15
SPEAKER - REMOVAL.................8A-14
SPEED CONTROL - DESCRIPTION........8P-1
SPEED CONTROL (4 SPEED EATX ONLY)
- OPERATION, INTERACTIVE.............8P-2
SPEED OPERATION - STANDARD
PROCEDURE, TIRE PRESSURE FOR
HIGH..............................22-17
SPEED SENSOR - AWD - INSTALLATION,
REAR WHEEL........................5-80
SPEED SENSOR - AWD - REMOVAL,
REAR WHEEL........................5-80
SPEED SENSOR - DESCRIPTION, ENGINE . 14-25
SPEED SENSOR - FWD - INSTALLATION,
REAR WHEEL........................5-81
SPEED SENSOR - FWD - REMOVAL,
REAR WHEEL........................5-81
SPEED SENSOR - INPUT - DESCRIPTION
. 21-239
SPEED SENSOR - INPUT -
INSTALLATION
......................21-240
SPEED SENSOR - INPUT - OPERATION
. . 21-240
SPEED SENSOR - INPUT - REMOVAL
....21-240
SPEED SENSOR - INSTALLATION, FRONT
WHEEL
.............................5-80
30 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

TEMPERATURE SENSOR - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-22
TEMPERATURE SENSOR - 3.3/3.8L -
REMOVAL, ENGINE COOLANT............7-21
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - DESCRIPTION,
EVAPORATOR.......................24-22
TEMPERATURE SENSOR - DESCRIPTION,
INFRARED.....................24-23,24-35
TEMPERATURE SENSOR - DESCRIPTION,
INLET AIR..........................14-29
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT..............8M-12
TEMPERATURE SENSOR -
INSTALLATION, EVAPORATOR...........24-23
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - OPERATION,
EVAPORATOR.......................24-23
TEMPERATURE SENSOR - OPERATION,
INFRARED.....................24-24,24-35
TEMPERATURE SENSOR - OPERATION,
INLET AIR..........................14-29
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-23
TEMPERATURE SENSOR - REMOVAL,
EVAPORATOR.......................24-23
TEMPERATURE SENSOR -
SPECIFICATIONS, BATTERY.............8F-22
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT....8M-12
TENSION - STANDARD PROCEDURE,
CHECKING POWER STEERING BELT.........7-8
TENSION RELEASE - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER................5-58
TENSION RESET - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER................5-59
TENSION, SPECIFICATIONS -
ACCESSORY DRIVE BELT................7-5
TENSIONER - 2.4L - INSTALLATION,
BELT ...............................7-10
TENSIONER - 2.4L - REMOVAL, BELT......7-10
TENSIONER - 3.3/3.8L - INSTALLATION,
BELT ...............................7-12
TENSIONER - 3.3/3.8L - REMOVAL, BELT . . . 7-12
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-16
TENSIONER - OPERATION, SEAT BELT....8O-16
TENSIONER & PULLEY - INSTALLATION,
TIMING BELT.........................9-69
TENSIONER & PULLEY - REMOVAL,
TIMING BELT.........................9-68
TERMINAL - INSTALLATION.........8W-01-14
TERMINAL - REMOVAL.............8W-01-14
TERMINAL REPAIR - STANDARD
PROCEDURE, GRID LINE...............8G-3
TEST - DIAGNOSIS AND TESTING, A/C
COOL DOWN.........................24-4
TEST - DIAGNOSIS AND TESTING, A/C
PERFORMANCE.......................24-5
TEST - DIAGNOSIS AND TESTING,
CONTROL CIRCUIT...................8F-30
TEST - DIAGNOSIS AND TESTING,
COOLING SYSTEM LEAK.................7-2
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE
LEAKAGE.........................9-83,9-9
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION PRESSURE . . 9-83,9-9
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT............................8F-33
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT RESISTANCE.................8F-32
TEST - DIAGNOSIS AND TESTING,
HEATED MIRROR.....................8G-5
TEST - DIAGNOSIS AND TESTING,
HEATER PERFORMANCE................24-6
TEST - DIAGNOSIS AND TESTING,
POWER STEERING SYSTEM FLOW
AND PRESSURE
......................19-1
TEST - DIAGNOSIS AND TESTING, ROAD
. . . 8P-3
TEST - DIAGNOSIS AND TESTING, ROAD
. 21-119
TEST - DIAGNOSIS AND TESTING,
STARTING SYSTEM
...................8F-28
TEST - DIAGNOSIS AND TESTING,
SYSTEM
............................8G-3TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-13
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-13
TEST MODE, OPERATION - DRB IIIT
STATE DISPLAY.......................25-9
TESTS - DIAGNOSIS AND TESTING,
CLUTCH AIR PRESSURE..............21-122
TESTS - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE..............21-120
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-1
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-3
THERMOSTAT - 2.4L - INSTALLATION,
ENGINE COOLANT.....................7-23
THERMOSTAT - 2.4L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-24
THERMOSTAT - 3.3/3.8L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - DESCRIPTION, ENGINE
COOLANT............................7-22
THERMOSTAT - DIAGNOSIS AND
TESTING, ENGINE COOLANT.............7-23
THERMOSTAT - OPERATION, ENGINE
COOLANT............................7-22
THERMOWRAP - DESCRIPTION.........8F-19
THERMOWRAP - INSTALLATION.........8F-19
THERMOWRAP - OPERATION...........8F-19
THERMOWRAP - REMOVAL............8F-19
THIRD ROW - INSTALLATION, BENCH
SEAT RISER........................23-100
THIRD ROW - REMOVAL, BENCH SEAT
RISER............................23-100
THREAD REPAIR - DESCRIPTION, FRONT
CRADLE CROSSMEMBER...............13-9
THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD STRIPPED......9-145
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-5
THREADS - STANDARD PROCEDURE,
REPAIR OF DAMAGED OR WORN.....9-10,9-86
THREE PASSENGER BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW.......................8O-14
THREE PASSENGER BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-14
THREE ZONE - DESCRIPTION, MANUAL....24-1
THREE ZONE - OPERATION, MANUAL.....24-3
THREE ZONE ATC - OPERATION..........24-3
THROTTLE BODY - DESCRIPTION........14-34
THROTTLE BODY - INSTALLATION.......14-35
THROTTLE BODY - OPERATION.........14-34
THROTTLE BODY - REMOVAL...........14-35
THROTTLE CONTROL CABLE -
INSTALLATION.......................14-35
THROTTLE CONTROL CABLE - REMOVAL . . 14-35
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-36
THROTTLE POSITION SENSOR -
OPERATION.........................14-36
TIE ROD - INSTALLATION, OUTER.......19-34
TIE ROD - REMOVAL, OUTER...........19-34
TIMING BELT - INSTALLATION...........9-65
TIMING BELT - REMOVAL
...............9-63
TIMING BELT COVER(S) - INSTALLATION
. . . 9-62
TIMING BELT COVER(S) - REMOVAL
......9-61
TIMING BELT TENSIONER & PULLEY -
INSTALLATION
........................9-69
TIMING BELT TENSIONER & PULLEY -
REMOVAL
...........................9-68
TIMING CHAIN AND CAMSHAFT
SPROCKET - INSTALLATION
............9-157
TIMING CHAIN AND CAMSHAFT
SPROCKET - REMOVAL
................9-156
TIMING CHAIN COVER - INSTALLATION
. . . 9-155
TIMING CHAIN COVER - REMOVAL
......9-153
TIMING CHAIN WEAR - STANDARD
PROCEDURE, MEASURING
.............9-153
TIMING VERIFICATION - STANDARD
PROCEDURE, VALVE
..................9-153
TIRE - DESCRIPTION
..................22-13
TIRE AND WHEEL ASSEMBLY
(ALUMINUM WHEEL) - INSTALLATION
.....22-8TIRE AND WHEEL ASSEMBLY
(ALUMINUM WHEEL) - REMOVAL........22-7
TIRE AND WHEEL ASSEMBLY (STEEL
WHEEL) - INSTALLATION...............22-8
TIRE AND WHEEL ASSEMBLY (STEEL
WHEEL) - REMOVAL...................22-8
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-5
TIRE AND WHEEL MATCH MOUNTING -
STANDARD PROCEDURE................22-7
TIRE AND WHEEL ROTATION -
STANDARD PROCEDURE................22-7
TIRE AND WHEEL VIBRATION -
DIAGNOSIS AND TESTING..............22-1
TIRE INFLATION PRESSURES -
STANDARD PROCEDURE...............22-16
TIRE LEAK REPAIRING - STANDARD
PROCEDURE........................22-17
TIRE NOISE - DIAGNOSIS AND TESTING . . 22-14
TIRE PRESSURE FOR HIGH SPEED
OPERATION - STANDARD PROCEDURE . . . 22-17
TIRE PRESSURE MONITORING -
DESCRIPTION........................22-9
TIRE PRESSURE MONITORING -
OPERATION..........................22-9
TIRE PRESSURE SENSOR - DIAGNOSIS
AND TESTING.......................22-10
TIRE PRESSURE SENSOR RETRAIN -
STANDARD PROCEDURE...............22-10
TIRE (TEMPORARY) - DESCRIPTION,
SPARE .............................22-14
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING.......................22-16
TIRES - CLEANING...................22-17
TIRES - DESCRIPTION, RADIAL-PLY......22-14
TIRES - DESCRIPTION, REPLACEMENT . . . 22-14
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING...........................22-14
TO CYLINDER BORE FITTING -
STANDARD PROCEDURE, PISTON........9-42
TO FILLER NECK SEAL - DIAGNOSIS
AND TESTING, RADIATOR CAP...........7-27
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-9
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . 8W-01-10
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TONE WHEEL - INSPECTION.............5-82
TONE WHEEL RUNOUT, SPECIFICATIONS . . . 5-79
TOOLS - 2.4L ENGINE, SPECIAL..........9-21
TOOLS - 3.3/3.8L ENGINE, SPECIAL.......9-95
TOOLS - 41TE AUTOMATIC TRANSAXLE,
SPECIAL..........................21-183
TOOLS - BASE BRAKE SYSTEM, SPECIAL . . 5-10
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL......................8F-7
TOOLS - BODY, SPECIAL...............23-13
TOOLS - COOLING SYSTEM, SPECIAL......7-6
TOOLS - EXHAUST SYSTEM, SPECIAL.....11-4
TOOLS - FRONT SUSPENSION, SPECIAL....2-3
TOOLS - FUEL, SPECIAL...........14-23,14-3
TOOLS - OVERHEAD CONSOLE, SPECIAL . . 8M-6
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-34
TOOLS - POWER STEERING PUMP,
SPECIAL...........................19-43
TOOLS - POWER STEERING, SPECIAL.....19-9
TOOLS - REAR SUSPENSION, SPECIAL....2-28
TOOLS - SDP POWER TRANSFER UNIT,
SPECIAL............................21-8
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, DIAGNOSIS AND TESTING -
SPECIAL............................3-34
TOOLS, SPECIAL TOOLS - BATTERY
SYSTEM SPECIAL.....................8F-7
TOOLS, SPECIFICATIONS - SPECIAL......8F-23
TOOLS, T850 TRANSAXLE - SPECIAL
.......6-6
TOOLS, T850 TRANSAXLE - SPECIAL
.....21-58
TOP COVER - INSTALLATION,
INSTRUMENT PANEL
..................23-67
TOP COVER - REMOVAL, INSTRUMENT
PANEL
.............................23-67
TOP PAD ASSEMBLY - INSTALLATION,
INSTRUMENT PANEL
..................23-70
RSINDEX33
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com