2003 CADILLAC CTS parking brake

1-3 Memory Seat and Mirrors (If Equipped)
This feature allows you to program and recall memory
settings for the driver's seating and outside rearview
mirror driving positions for up to two drivers.
The buttons for this feature
are located on the driver's
door armrest.
Use the following steps to program the buttons:
1. Adjust the driver's seat including the seatback
recliner and both outside mirrors.
2. Press and hold button 1 for at least three seconds.
Two beeps will sound to confirm that the seat and
mirror positions have been saved.
3. Repeat the procedure for a second driver
using button 2.If your vehicle has an automatic transmission, the
vehicle must be in PARK (P) to recall the stored driving
positions. If your vehicle has a manual transmission and
the engine is running, the parking brake must be set to
recall the memory seat driving positions. The stored
driving positions can be recalled without setting the
parking brake if the vehicle is off.
Press one of the numbered memory buttons to recall the
stored setting. Each time a memory button is pressed, a
single beep will sound.
Three chimes will sound and the setting will not be
recalled if you press button 1 or 2 while the engine is
running and the vehicle is not in PARK (P) on an
automatic transmission or the parking brake is not
set on a manual transmission.
If you would like the stored driving positions to be
recalled when unlocking your vehicle with the remote
keyless entry transmitter or when you place the key in
the ignition, see ªVehicle Programming and
Personalization Featuresº in the Index.
To stop recall movement of the memory feature at any
time, press one of the power seat or mirror controls.

1-4
Two personalized exit positions can also be
programmed. Use the following steps to program
exit positions:
1. Press memory seat button 1 or the button with
the unlock symbol on the remote keyless entry
transmitter with the number 1 on the back to recall
the drive position.
2. Adjust the driver's seat to the desired exit position.
3. Press and hold the exit button located above
buttons 1 and 2 on the driver's door armrest for
at least three seconds.
Two beeps will sound to confirm that the exit
position has been saved.
4. Repeat the procedure for a second driver using
memory seat button 2 or the remote keyless entry
transmitter with the number 2 on the back.To recall the stored exit positions, press and release the
exit button. One beep will sound, and the seat will move
to the previously stored exit position for the currently
identified driver. If an exit position has not been stored
for this driver, the seat will move all the way back. The
position of the outside mirrors is not stored or recalled
for the exit position.
If your vehicle has an automatic transmission, the
vehicle must be in PARK (P) to recall the exit positions.
For a manual transmission, the parking brake must
be set if the engine is running to recall the stored
exit positions.
Three chimes will sound and the exit setting will not be
recalled if you press the exit button while the engine is
running and the vehicle is not in PARK (P) on an
automatic transmission or the parking brake is not set on
a manual transmission.
If you would like your stored exit position to be recalled
when unlocking the vehicle with the remote keyless
entry transmitter or when the ignition is turned off and
the driver's door is opened, see ªVehicle Programming
and Personalization Featuresº in the Index.

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-5 Keys
2
-7 Door Locks
2
-10 Remote Keyless Entry System
2
-16 Trunk Lid
2
-19 Theft
2
-21 Immobilizer
2
-24 New Vehicle ªBreak-Inº
2
-24 Ignition Positions
2
-27 Starting Your Engine
2
-28 Engine Coolant Heater (If Equipped)
2
-30 Automatic Transmission Operation
2
-37 Manual Transmission Operation
2
-38 Parking Brake
2
-40 Shifting Into PARK (P)
(Automatic Transmission Only)
2
-42 Shifting Out of PARK (P)
(Automatic Transmission Only)
2
-42 Parking Your Vehicle
(Manual Transmission Only)2
-43 Parking Over Things That Burn
2
-44 Engine Exhaust
2
-44 Running Your Engine While You're Parked
(Automatic Transmission)
2
-46 Turn Signal/Multifunction Lever
2
-56 Exterior Lamps
2
-59 Interior Lamps
2
-60 Mirrors
2
-70 OnStar
System (If Equipped)
2
-74 Sunroof (Option)
2
-75 HomeLink
Transmitter (If Equipped)
2
-80 The Instrument Panel -- Your
Information System
2
-85 Warning Lights, Gages and Indicators
2
-99 Driver Information Center (DIC)
2
-130 Vehicle Programming and
Personalization Features
2
-153 Navigation (Option)

2-16
Trunk Lid
CAUTION:
It can be dangerous to drive with the trunk lid
open because carbon monoxide (CO) gas can
come into your vehicle. You can't see or smell
CO. It can cause unconsciousness and even death.
If you must drive with the trunk lid open or if
electrical wiring or other cable connections must
pass through the seal between the body and the
trunk lid:

Make sure all other windows are shut.

Turn the fan on your heating or cooling
system to its highest speed and select the
control setting that will force outside air
into your vehicle. See ªComfort Controlsº
in the Index.

If you have air outlets on or under the
instrument panel, open them all the way.
See ªEngine Exhaustº in the Index.
Remote Trunk Release Button
The remote trunk release
button is located on the
lower portion of the
driver's door.
To use this feature, an automatic transmission must
be in PARK (P) or NEUTRAL (N) and your manual
transmission must be in NEUTRAL with the parking
brake set.
Press the button to open the trunk. You can also press
the button with the trunk symbol on the remote keyless
entry transmitter to open the trunk.
When the trunk lid opens, a light inside the trunk
will come on. The light will go out when the trunk
lid is closed.

2-28
Manual Transmission
The gear selector should be in neutral and the parking
brake engaged. Hold the clutch pedal to the floor and
start the engine. Your vehicle won't start if the clutch
pedal is not all the way down
-- that's a safety feature.
1. With your foot off the accelerator pedal, turn your
ignition key to START. Then, just let go of the key;
the engine starts automatically. The idle speed will
go down as your engine gets warm.
2. If your engine won't start (or starts but then stops),
it could be flooded with too much gasoline. Try
pushing your accelerator pedal all the way to the
floor and holding it there as you turn the key to
START. If the vehicle starts briefly but then stops
again, do the same thing.
NOTICE:
Your engine is designed to work with the
electronics in your vehicle. If you add electrical
parts or accessories, you could change the way
the engine operates. Before adding electrical
equipment, check with your dealer. If you don't,
your engine might not perform properly.
Engine Coolant Heater (If Equipped)
In very cold weather, 0
F (-18
C) or colder, the engine
coolant heater can help. You'll get easier starting and
better fuel economy during engine warm
-up. Usually,
the coolant heater should be plugged in a minimum of
four hours prior to starting your vehicle. At temperatures
above 32
F (0
C), use of the coolant heater is
not required.

2-30
Automatic Transmission Operation
The automatic transmission shift lever is located on the
center console between the front seats.
There are several different positions for the shift lever.PARK (P): This position locks the rear wheels. It's the
best position to use when you start the engine because
your vehicle can't move easily.
CAUTION:
It is dangerous to get out of your vehicle if the
shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.
Don't leave your vehicle when the engine is
running unless you have to. If you have left the
engine running, the vehicle can move suddenly.
You or others could be injured. To be sure your
vehicle won't move, even when you're on fairly
level ground, always set your parking brake and
move the shift lever to PARK (P).
See ªShifting Into PARK (P)º in the Index.
If you're pulling a trailer, see ªTowing a Trailerº
in the Index.

2-37
Manual Transmission Operation
The following explains how to operate your vehicle's
manual transmission.
This is the shift pattern
for your vehicle.
FIRST (1): Press the clutch and shift into FIRST (1).
Then, slowly let up on the clutch pedal as you press the
accelerator pedal.
You can shift into FIRST (1) when you're going less
than 20 mph (32 km/h). If you've come to a complete
stop and it's hard to shift into FIRST (1), put the shift
lever in NEUTRAL and let up on the clutch. Press the
clutch pedal back down. Then try shifting into
FIRST (1) again.SECOND (2): Press the clutch pedal to the floor
as you let up on the accelerator pedal and shift into
SECOND (2). Then, slowly let up on the clutch pedal
as you press the accelerator pedal.
THIRD (3), FOURTH (4), and FIFTH (5): Shift into
THIRD (3), FOURTH (4) and FIFTH (5) the same way
you do for SECOND (2). Slowly let up on the clutch
pedal as you press the accelerator pedal.
To stop, let up on the accelerator pedal and press the
brake pedal. Before the vehicle comes to a complete
stop, press the clutch pedal and brake pedal, and shift
into NEUTRAL.
NEUTRAL: Use this position when you idle the engine.
REVERSE (R): Use this gear to back up. Press the
clutch pedal and shift into REVERSE (R). Slowly let up
on the clutch pedal as you press the accelerator pedal.
Use REVERSE (R), along with the parking brake, when
you park your vehicle. See ªParking Your Vehicle
(Manual Transmission Only)º later in this section for
more information.
If your vehicle has a manual transmission, in order for
you to remove the key from the ignition, you must press
the key release button on the ignition switch. See ªKey
Release Buttonº in the Index for more information.

2-38
Shift Speeds
CAUTION:
If you skip a gear when you downshift, you could
lose control of your vehicle. You could injure
yourself or others. Don't shift down more than
one gear at a time when you downshift.
NOTICE:
If you skip more than one gear when you
downshift, or if you race the engine when you
release the clutch pedal while downshifting, you
could damage the clutch or the transmission.
If the vehicle speed drops below 20 mph (32 km/h), or
if the engine is not running smoothly, you should
downshift to the next lower gear. You may have to
downshift two or more gears to keep the engine running
smoothly or for good performance.
Parking Brake
The parking brake pedal
is located on the lower
portion of the instrument
panel to the left of the
steering wheel.
To set the parking brake, hold the regular brake pedal
down with your right foot and push the parking brake
pedal down with your left foot.