2003 CADILLAC CTS light

2-23
Canadian Owners: If you lose or damage your keys,
only a GM dealer can service the theft
-deterrent system
to have new keys made. To program additional keys you
will require two current driver's keys. You must add a
step to the following procedure. After Step 2, repeat
Steps 1 and 2 with the second current driver's key.
Then continue with Step 3.
To program a new key do the following:
1. Verify that the new key has PK3+ stamped on it.
2. Insert the current driver's key in the ignition and
start the engine. If the engine will not start see your
dealer for service.
3. After the engine has started, turn the key to OFF, and
remove the key.
4. Insert the key to be programmed and turn it to ON
within ten seconds of removing the previous key.5. The security light will turn off once the key has been
programmed. It may not be apparent that the security
light went on due to how quickly the key is
programmed.
6. Repeat the Steps 1 through 4 if additional keys are to
be programmed.
If you are ever driving and the security light comes on
and stays on, you will be able to restart your engine if
you turn it off. The theft
-deterrent system, however, is
not working properly and must be serviced by your
dealer. Your vehicle is not protected by the
theft
-deterrent system at this time.
In an emergency, contact Cadillac Roadside Assistance.
See ªRoadside Assistanceº in the Index.

2-35
Sport Mode Button
(Automatic Transmission Only)
This button allows you to change the driving mode of
the vehicle from the normal driving mode to a sportier
driving mode. In sport mode the vehicle will have firmer
shifting and increased performance.
The sport mode button is
located on the center
console near the
transmission shift lever.
Press the button once to turn on the sport mode.
Press the button again to return to normal driving mode.
This light located on the
instrument panel cluster
will come on when the sport
mode is active.
When you turn off the ignition while driving in sport
mode, the vehicle will remain in sport mode. Press the
sport mode button again to turn off the feature and
return to normal driving mode.

2-36
Winter Driving Mode Button
(Automatic Transmission Only)
This feature provides more traction during slippery
conditions by using THIRD (3) gear instead of
SECOND (2) when you begin to accelerate from a
stopped position.
The winter driving mode
button is located on the
center console near the
transmission shift lever.
Press this button once to turn on the winter driving
mode feature. Press it again to turn the feature off.
The winter driving mode feature works when the vehicle
is in any gear except SECOND (2).
This light on the instrument
panel cluster will come on
when the winter driving
mode is active.
When you turn off the ignition while using this feature,
winter mode is automatically turned off. The vehicle
will return to normal driving mode. You must reselect
the winter driving mode feature each time you restart the
vehicle if you wish to use the feature.
The transmission will be in THIRD (3) gear when the
vehicle begins to move. Once the vehicle is moving, the
vehicle will upshift normally.
The transmission will downshift when the accelerator
pedal is pressed and held for more than two seconds.
This feature is not intended for continuous use or for
use when the vehicle is stuck in sand, mud, ice, snow or
gravel. If your vehicle becomes stuck, see ªRocking
Your Vehicleº in the Index for more information on
how to free it.

2-39
To release the parking brake, pull the release lever
located to the left of the steering wheel on the
instrument panel.
If the ignition is on, the brake system warning light
on the instrument panel cluster should come on. If it
doesn't, you need to have your vehicle serviced. See
ªBrake System Warning Lightº in the Index for more
information.
NOTICE:
Do not drive your vehicle with the parking brake
on. Driving with the parking brake engaged can
cause your vehicle's rear brakes to overheat. You
may have to replace them, and you could also
damage other parts of your vehicle.
A warning chime will sound if the parking brake is set,
the ignition is on and the vehicle begins to move. To
stop the chime, fully release the parking brake.
If you are towing a trailer and parking on a hill, see
ªTowing a Trailerº in the Index for more information.

2-47
Turn Signal On Chime
If the turn signal is left on for approximately 1 mile
(1.61 km), a warning chime will sound and the
Turn Signal On message will appear on the Driver
Information Center (DIC) display. See ªTurn Signal
On Messageº later in this section for more information.
Headlamps
The exterior lamp control is located at the end of the
turn signal/multifunction lever.
: Turn the control with this symbol on it to operate
the exterior lamps.
The exterior lamp control has three positions:
: Turning the control to this position turns off all
lamps except the Daytime Running Lamps (DRL).
: Turning the control to this position turns on the
parking lamps together with the following:

Sidemarker Lamps

Taillamps

License Plate Lamps

Instrument Panel Lights
: Turning the control to this position turns on the
headlamps, together with the previously listed lamps
and lights.
AUTO (Automatic): Turning the control to this
position puts the headlamps in automatic mode. AUTO
mode will turn the exterior lamps on and off depending
upon how much light is available outside of the vehicle.
Wiper
-Activated Headlamps
This feature activates the headlamps and parking lamps
after the windshield wipers have been in use for
approximately six seconds. For this feature to work, the
exterior lamp control must be in AUTO.
When the exterior lamp control is off or in the parking
lamp position and the windshield wiper control is in any
position except off, the Headlamps Suggested message
will appear on the DIC display. See ªHeadlamps
Suggested Messageº later in this section for more
information.
When the ignition is turned to OFF, the wiper
-activated
headlamps will immediately turn off. They will also turn
off if the windshield wiper control is turned off.

2-48
Headlamp High/Low-Beam Changer
Push forward on the turn signal/multifunction lever to
change the headlamps from low to high beam. Pull the
lever back and then release it to change from high to
low beam.
This light on the instrument
panel cluster will be on,
indicating high
-beam usage.
Lamps On Reminder
A warning chime will sound if the exterior lamp control
is left on in either the headlamp or parking lamp
position and the driver's door is opened with the
ignition off.
Flash-To-Pass Feature
This feature allows you to use the high-beam headlamps
to signal the driver in front of you that you want to pass.
Pull and hold the turn signal/multifunction lever toward
you to use. When you do, the following will occur:

If the headlamps are either off, in low
-beam or in
Daytime Running Lamps (DRL) mode, the
high
-beam headlamps will turn on. They'll stay on
as long as you hold the lever there. Release the lever
to turn them off.

If the headlamps are in high
-beam mode, they will
switch to low beam. To return to high
-beam, push
the lever away from you.

2-54
Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use
cruise control.
1. Press the cruise control on/off button to turn cruise
control on. An indicator light will come on to show
that the cruise control is on.
2. Accelerate to the speed you want.
3. Press either the plus or minus button and release it.
This will set the cruise control.
4. Remove your foot from the accelerator pedal.
This light on the instrument
panel cluster will come on
when cruise control is on.
It will go out when cruise
control is turned off.
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This shuts off the cruise
control. But you don't need to reset it.
Once the vehicle is traveling approximately 25 mph
(40 km/h) or more, you can press the resume/accelerate
button to return to your desired preset speed. The cruise
control light will be displayed again.
The vehicle will return to and stay at your preset speed.
If you press and hold the resume/accelerate button, the
vehicle speed will increase until you release the button
or apply the brake. Unless you want to go faster, do not
press and hold the resume/accelerate button.

2-56
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Applying the brake or shifting
into a lower gear will take you out of cruise control. If
you need to apply the brake or shift to a lower gear due
to the grade of the downhill slope, you may not want to
attempt to use your cruise control feature.Ending Cruise Control
To turn off the cruise control, step lightly on the brake
pedal, or press the cruise control on/off button on the
steering wheel.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.
Exterior Lamps
Headlamps
See ªTurn Signal/Multifunction Leverº listed previously
in this section for more information on the headlamps.