2003 CADILLAC CTS mirror

2-64
Curb View Assist Mirror (If Equipped)
If your vehicle is equipped with the memory seat and
mirrors, it will also be capable of performing the curb
view assist mirror feature. This feature will cause the
passenger's mirror to tilt to a preselected position when
the vehicle is shifted into REVERSE (R). Use this
feature to view the curb when you are parallel parking.
When the vehicle is shifted out of REVERSE (R) and a
five
-second delay has occurred, the passenger's mirror
will return to its original position.
If further adjustment is needed after the mirror is
tilted, the mirror controls can be used. See ªPower
Outside Rearview Mirrorsº listed previously for
more information.
This feature can be enabled/disabled through the DIC.
See ªVehicle Programming and Personalization
Featuresº in the Index for more information.
Convex Outside Mirror
Your passenger's side mirror is convex. A convex
mirror's surface is curved so you can see more from the
driver's seat.
CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could hit a vehicle on your right. Check your
inside mirror or glance over your shoulder before
changing lanes.
Heated Outside Rearview Mirrors
When you operate the rear window defogger, it also
warms both outside rearview mirrors to help clear them
of fog or ice. See ªRear Window Defoggerº in the Index
for more information.

2-67
Cigarette Lighter
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overheat, damaging the
lighter and the heating element.
The cigarette lighter is located next to the ashtray. The
vehicle does not have any cigarette lighters for the rear
seat passengers.
Press the lighter all the way in and release it. It will pop
back out by itself once the element has heated for use.
Cigarette lighters can be used to provide power to
accessories. See ªAccessory Power Outletsº in the
Index for more information.
Sun Visors
Swing down the primary visor to block out glare. It can
also be detached from the center mount and moved to
the side to block glare from that direction.
The driver's sunshade may also have buttons for a
built
-in garage door opener and a recording device. See
ªHomeLink
Transmitterº and ªTravel Note Recorderº
later in this section for more information.
Lighted Visor Vanity Mirror
Pull the visor down and lift the cover. The light will
automatically come on. The light will go out when you
close the cover.

2-130
Vehicle Programming and
Personalization Features
Your vehicle is equipped with personalization that
allows you to program certain features to a preferred
setting for up to two people. The number of
programmable features varies depending upon which
model of the vehicle is purchased.
On all vehicles, features such as climate control settings,
radio preset settings, exterior lighting at unlock, remote
lock and unlock confirmation, and automatic door locks
have already been programmed for your convenience.
Some vehicles are equipped with additional features that
can be programmed including the seat and outside
rearview mirror position. The optional navigation
system screen preferences will remain at the last set
position.
If your vehicle is equipped with the ability to program
additional personalization features, the driver's
preferences are recalled by pressing the unlock button
on the remote keyless entry transmitter, 1 or 2, or
by pressing the appropriate memory button, 1 or 2,
located on the driver's door. Certain features can be
programmed not to recall until the key is placed in the
ignition. To change feature preferences you must use
one of the following procedures.
Entering the Personalization Menu
To enter the feature programming mode, use one of the
following procedures:
Base Audio System
1. Turn the ignition to ON, but do not start the engine.
Make sure an automatic transmission is in PARK (P)
or a manual transmission has the parking brake set.
2. If your vehicle has memory settings, press the
appropriate memory button, 1 or 2, located on the driver's
door armrest. The DIC display will show either Driver 1
or 2 depending on which button was selected.
3. Press the TUNE/SEL knob once to access the main
menu of the DIC.
4. Turn the TUNE/SEL knob until SETUP is highlighted.
5. Press the TUNE/SEL knob once to access the
SETUP menu.
6. Scroll to the feature you want to change, and press
the TUNE/SEL knob to turn the feature on or off.
If the feature is turned on, a check mark will appear
next to the feature name.
If none of the personalization items are turned on,
turn on the personalization menu by pressing the
TUNE/SEL knob. The list of features will then
appear, and you can repeat Step 6.

2-133
Configure Display Keys (Base Audio System Only)
This feature allows you to customize the functions of
the four soft keys located to the left and right of the
audio display. Most of the available functions are
audio
-system related. See ªAudio Systemsº in the
Index for more information.
Remote Recall Memory/Recall Driving Positions
(If Equipped)
This feature recalls any previously programmed seat and
mirror controls when the unlock button on the remote
keyless entry transmitter is pressed.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.2. Scroll to REMOTE RECALL MEMORY to
highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Recall Driving Positions and press the knob
once to select it.
When the mode is turned on, an X will appear in the
box to the left.
If Remote Exit Recall or Key In Recall Memory were turned
on previously, selecting Remote Recall Memory/Recall
Driving Positions will override that choice.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-135
Key in Recall Memory (If Equipped)
This feature recalls any previously programmed seat
and mirror positions when the key is inserted into the
ignition.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to KEY IN RECALL MEMORY to
highlight it.3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Key In Recall Memory and press the knob
once to select it.
When the mode is turned on, an X will appear in the
box to the left.
If Remote Recall Memory/Recall Driving Positions was
turned on previously, selecting Key In Recall Memory
will override that choice.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-150
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Lock Passenger Window using the
TUNE/SEL knob to highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, an X will appear in the
box to the left.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
Mirror to Curb in Reverse (If Equipped)
This feature will move the passenger's outside rearview
mirror to a curb view position when the shift lever is
shifted into REVERSE (R), and it will return the mirror
to the last known driving position when the shift lever is
moved out of REVERSE (R). See ªCurb View Assist
Mirrorº in the Index for more information.Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to MIRROR TO CURB IN REV using the
TUNE/SEL knob to highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.

2-151
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Mirror to Curb in Reverse using the
TUNE/SEL knob to highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, an X will appear in the
box to the left.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
Enhanced Chime Volume
This feature allows you to adjust the volume level of the
vehicle's warning chimes. The chime volume cannot be
turned off, only adjusted.Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 1. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to ENHANCED CHIME VOLUME using the
TUNE/SEL knob to highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between the normal and loud settings.
You will hear a chime as an example of the volume
level chosen.

3-6 Air Conditioning
On hot days, open the windows long enough to let hot
inside air escape. This reduces the time it takes for your
vehicle to cool down. Then keep your windows closed
for the air conditioner to work its best.
While the system is in AUTO, it will use recirculation
as necessary to cool the air.
Defogging and Defrosting
When the mode switch is set for floor/defrost or the
defrost button is pressed, outside air will be selected
automatically. This helps clear the windshield more
quickly. Adjust the temperature and set the fan speed to
the highest setting. When the windshield is clear, adjust
the fan speed for maximum defrosting to a lower setting
or return to AUTO mode.
Recirculation is not available in the defrost mode, and
the air conditioning compressor cannot be turned off in
this mode.
For maximum side window defogging, turn the outboard
outlet thumbwheels to the side window defogger setting.
See ªVentilation Systemº later in this section for more
information on the outlet settings.
Rear Window Defogger
When the rear window defogger is turned on, the rear
window and both outside rearview mirrors are heated to
remove fog from the surface of the glass.
The rear window defogger
button is located on the
climate control panel to the
right of the defrost button.
Press the button to turn on the rear defogger. Press the
button again to turn the system off.
The system will automatically shut off after 10 minutes
unless your vehicle is traveling more than 30 mph
(48 km/h). If further defogging is desired once the
system is off, press the button again. The system will
automatically shut off after five minutes for any cycles
after the initial activation.