2003 CADILLAC CTS brakes

2-31
Ensure the shift lever is fully in PARK (P) before
starting the engine. Your vehicle has an automatic
transmission shift lock control system. You must fully
apply your regular brakes before you can shift from
PARK (P) when the ignition key is in ON. If you cannot
shift out of PARK (P), ease pressure on the shift lever.
Push the shift lever all the way into PARK (P) while
pressing the button on the shift lever as you maintain
brake application. Then move the shift lever into the
gear you wish. See ªShifting Out of PARK (P)º in
the Index.
NOTICE:
Shifting to REVERSE (R) while your vehicle is
moving forward could damage your
transmission. Shift to REVERSE (R) only after
your vehicle has stopped.
REVERSE (R): Use this gear to back up.
At low vehicle speeds, you can also use REVERSE (R)
to rock your vehicle back and forth to get out of snow,
ice or sand without damaging your transmission. See
ªStuck in Sand, Mud, Ice or Snowº in the Index for
additional information.NEUTRAL (N): In this position, the engine doesn't
connect with the wheels. To restart when you're already
moving, use NEUTRAL (N) only. You can also use
NEUTRAL (N) when your vehicle is being towed.
CAUTION:
Shifting into a drive gear while your engine is
ªracingº (running at high speed) is dangerous.
Unless your foot is firmly on the brake pedal,
your vehicle could move very rapidly. You could
lose control and hit people or objects. Don't shift
into a drive gear while your engine is racing.
NOTICE:
Damage to your transmission caused by shifting
out of PARK (P) or NEUTRAL (N) with the
engine racing isn't covered by your warranty.

2-32
AUTOMATIC OVERDRIVE (D): This position is
for normal driving. If you need more power for passing,
and you're:

Going less than 35 mph (55 km/h), push the
accelerator pedal about halfway down.

Going about 35 mph (55 km/h) or more, push the
accelerator all the way down.
The transmission will shift down to a lower gear and
have more power.
NOTICE:
If your vehicle seems to start up rather slowly, or
if it doesn't seem to shift gears as you accelerate,
something may be wrong with a transmission
system sensor. If you drive very far that way,
your vehicle can be damaged. So if this happens,
have your vehicle serviced right away. Until then,
you can use FOURTH (4) when you are driving
less than 35 mph (55 km/h) and AUTOMATIC
OVERDRIVE (D) for higher speeds.
FOURTH (4): This position is also used for normal
driving, however, it offers more power and lower fuel
economy than AUTOMATIC OVERDRIVE (D).
Here are examples for using FOURTH (4) instead of
AUTOMATIC OVERDRIVE (D).

When driving on hilly, winding roads.

When going down a steep hill.
THIRD (3): This position gives you more power. You
can use THIRD (3) on hills. It can help control your
speed as you go down steep mountain roads, but then
you would also want to use your brakes off and on.
If the shift lever is put into THIRD (3), the transmission
won't shift into THIRD (3) until the vehicle is moving
slowly enough.

2-33
SECOND (2): This position gives you even more
power than THIRD (3). You can use it on very steep
hills, or in deep snow or mud. (If the shift lever is put
in SECOND (2), the transmission won't shift into
SECOND (2) until the vehicle is going slowly enough).
NOTICE:
If the vehicle's wheels can't turn, don't try to
drive. This might happen if you were stuck in
very deep sand or mud or were up against a solid
object. You could damage your transmission.
Also, if you stop when going uphill, don't hold
your vehicle there with only the accelerator
pedal. This could cause overheating and damage
the transmission. Use your brakes to hold your
vehicle in position on a hill.
Shift Lock Release
(Automatic Transmission Only)
If your vehicle has a dead battery or a battery with low
voltage, you can still shift the vehicle into PARK (P) and
remove the ignition key. Use the following procedure to
release the shift lever:
1. Pull up on the rear part of the leather boot that
surrounds the shift lever.
2. Fold the boot upward to expose the mechanism
beneath the shift lever.

2-39
To release the parking brake, pull the release lever
located to the left of the steering wheel on the
instrument panel.
If the ignition is on, the brake system warning light
on the instrument panel cluster should come on. If it
doesn't, you need to have your vehicle serviced. See
ªBrake System Warning Lightº in the Index for more
information.
NOTICE:
Do not drive your vehicle with the parking brake
on. Driving with the parking brake engaged can
cause your vehicle's rear brakes to overheat. You
may have to replace them, and you could also
damage other parts of your vehicle.
A warning chime will sound if the parking brake is set,
the ignition is on and the vehicle begins to move. To
stop the chime, fully release the parking brake.
If you are towing a trailer and parking on a hill, see
ªTowing a Trailerº in the Index for more information.

2-42
Shifting Out of PARK (P)
(Automatic Transmission Only)
Your vehicle has an automatic transmission shift lock
control system. You have to fully apply your regular
brakes before you can shift from PARK (P) when the
ignition is in ON. See ªAutomatic Transmissionº in
the Index.
If you cannot shift out of PARK (P), ease the pressure
on the shift lever. Push the shift lever all the way into
PARK (P) while pushing the button on the shift lever as
you maintain brake application. Then move the shift
lever into the gear you want. If you ever hold the pedal
down but still can't shift out of PARK (P), try the
following:
1. Turn the ignition key to ACCESSORY. Open and
close the driver's door to turn off the RAP feature.
2. Apply and hold the brake until the end of Step 4.
3. Shift to NEUTRAL (N).
4. Start the vehicle and then shift to the drive gear
you want.
5. Have the vehicle fixed as soon as you can.
Parking Your Vehicle
(Manual Transmission Only)
Before you get out of your vehicle firmly apply the
parking brake. Turn the ignition key to OFF, press the
release button and remove the key. See ªManual
Transmission Key Release Buttonº in the Index for
more information.
If you are towing a trailer, see ªTowing a Trailerº in
the Index.

2-53
Cruise Control
: On/Off
+: Resume/Accelerate, Set
-: Coast/Decelerate, Set
The buttons used to operate cruise control are located at
the bottom of the steering wheel.
With cruise control, you can maintain a speed of
approximately 25 mph (40 km/h) or more without
keeping your foot on the accelerator. This is helpful on
long trips. Cruise control does not work at speeds below
about 25 mph (40 km/h).When you apply your brakes, the cruise control
shuts off.
CAUTION:

Cruise control can be dangerous where you
can't drive safely at a steady speed. So,
don't use your cruise control on winding
roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don't
use cruise control on slippery roads.
If your vehicle is in cruise control when the traction
control system begins to limit wheel spin, the cruise
control will automatically disengage. See ªTraction
Control Systemº and ªStabilitrak Systemº in the Index.
When road conditions allow you to safely use it again,
you may turn the cruise control back on.

2-89
Anti-Lock Brake System Warning Light
With the anti-lock brake
system, the light(s) will
come on when your engine
is started and may stay
on for several seconds.
That's normal.
If the ABS warning light comes on and stays on, there
may be a problem with the antilock portion of the brake
system. If the red BRAKE light is not on, you still have
brakes, but you don't have antilock brakes. See ªBrake
System Warning Lightº earlier in this section.If the light stays on, turn the ignition to OFF. Or, if the
light comes on when you're driving, stop as soon as
possible and turn the ignition off. Then start the engine
again to reset the system. If the light still stays on, or
comes on again while you're driving, your vehicle needs
service. If the regular brake system warning light isn't
on, you still have brakes, but you don't have anti
-lock
brakes. If the regular brake system warning light is also
on, you don't have anti
-lock brakes and there's a
problem with your regular brakes. See ªBrake System
Warning Lightº earlier in this section.
The anti
-lock brake system warning light will come on
briefly when you turn the ignition key to ON. This is
normal. If the light doesn't come on then, have it fixed
so it will be ready to warn you if there is a problem.
If the ABS light stays on or comes on while you are
driving, pull off the road as soon as possible and stop
carefully. Try resetting the system by turning the
ignition off then back on. If the ABS light still stays on
or comes back on again while you are driving, your
vehicle needs service. Have the anti
-lock brake system
inspected as soon as possible.

2-124
Traction Engaged
This symbol appears
with the Traction
Engaged message.
This message will appear when the traction control
system is actively limiting wheel spin. Slippery road
conditions may exist if this message is displayed, so
adjust your driving accordingly. The message will stay
on for a few seconds after the traction control system
stops limiting wheel spin. See ªTraction Control
Systemº in the Index for more information.Traction SuspendedThis symbol appears
with the Traction
Suspended message.
This message will appear when the traction control
system has been temporarily shut off because your
vehicle's brakes have overheated. This message does not
indicate a problem with your vehicle's traction control
system. See ªTraction Control Systemº in the Index for
more information.