2003 ASTON MARTIN DB AR1 Q tow

E - Security Systems
1-E-4
Unlocking the Car, Disarming the Alarm
Point the key fob towards the rear window and press the left button once.
The following events will occur:
1. The green light on the key fob will light while the left button is pressed.
2. The car doors and fuel filler flap will unlock.
3. The direction indicators will flash (in markets where visible alarm signals
are permitted and programmed).
4. The alarm system will be switched off.
Locking the Car, Arming the Alarm
Point the key fob towards the rear window and press the left button. The
following events will occur:
1. The green light on the key fob will light while the left button is pressed.
2. The car doors and fuel filler flap will lock.
3. The direction indicators will flash once (in markets where visible alarm
signals are permitted).
4. The alarm system will be switched on.
Alarm and Security System Protection
With the alarm system armed, any attempt to open a door, the boot or the
bonnet will result in full alarm activation.
(See also the engine immobilisation protection afforded by the PATs system)

F - Owner Maintenance
1-F-18
The Vehicle Toolkit
On vehicles fitted with a space-saver spare wheel , the tool kit is stored in
the spare wheel insert.
On vehicles without the spare wheel option the vehicle toolkit is stored in
a well within the boot floor and covered by a boot floor liner panel. The
standard toolkit consists of the following items:
• 2 Tyre Inflation Aerosols and Warning Labels
• 1 Tyre Pressure Gauge
• 1 Towing Eye
• 1 Pair of Pliers
• 1 Screwdriver
• 1 Pair of Gloves
• 1 Locking Wheelnut Socket (UK only)
• 1 Bulb and Fuse Kit
• 1 Allen Key
Lift up the boot floor to access the toolkit.

F - Owner Maintenance
1-F-26
Vehicle Recovery
General
The preferred method for moving a defective vehicle is to have it carried in
a purpose built covered vehicle transporter.
Ensure that the recovery team are aware of the following instructions:
Transporting and Towing
The front towing eye is primarily for emergency use when towing for short
distances, e.g. removing the vehicle if it is causing an obstruction, or
winching the vehicle onto a covered flatbed transporter.
If moving a DB AR1 in such a situation, remove the towing eye access plate
in the grille using the screwdriver from the toolkit. Fit the front towing eye
to the stud in the front grille aperture.
Caution: Take care to protect the paintwork when fitting the towing eye.

F - Owner Maintenance
1-F-27 The DB AR1 may then be winched onto a transporter or towed to a safe
location using a rope, provided that the following precautions are observed:
Transporting
If the vehicle is to be transported on a trailer or flat bed transporter, the
handbrake must be applied and the wheels chocked. Vehicles fitted with
Touchtronic transmission must have the gear selector lever moved to N or
D but NEVER in P. The parking lock may be damaged if the vehicle is
transported with the gear selector lever in P.
Four tie-down brackets are provided, two on each axle. These are NOT
suitable for solid bar towing.
Front Axle Tie-Down Rear Axle Tie Down
Vehicles with Defective Touchtronic Transmission
The vehicle must be carried on a transporter or towed with the rear wheels
clear of the ground (see suspended towing) or towed with the propeller shaft
disconnected at the final drive input flange. If the propeller shaft is
disconnected, it must be firmly secured away from the final drive flange.

F - Owner Maintenance
1-F-28
Suspended Towing
Do NOT tow with sling-type equipment since damage to the bodywork may
result.
Take care when using 'spectacle frame' type towing equipment that the
towing device is well clear of the front or rear apron. Body damage may
occur if the vehicles pass over uneven road surfaces.
Adhere to Towing Regulations
In certain countries the registration number of the towing vehicle and an ON
TOW sign or warning triangle must be displayed in a prominent position at
the rear of the vehicle being towed.
Front Suspended Tow
Caution: To prevent body damage ensure an adequate clearance is
maintained between the car body and (1) the ground and (2) the 'spectacle
frame' of the towing vehicle while your car is being towed.
1. Remove the ignition key from the ignition.
2. Vehicles with manual transmission: Place the gear lever in neutral.
Vehicles with automatic transmission:
Disconnect the propeller shaft at the final drive input flange.
Ensure that the propeller shaft is firmly secured away from the final drive
input flange.

F - Owner Maintenance
1-F-29 3. Raise the vehicle using a 'spectacle frame' type lifting device with a cradle
positioned under each front wheel as shown below.
Rear Suspended Tow
Caution: To prevent body damage ensure an adequate clearance is
maintained between the car body and (1) the ground and (2) the 'spectacle
frame' of the towing vehicle while your car is being towed.
1. Remove the ignition key from the ignition/steering lock.
2. Raise the vehicle using a 'spectacle frame' style lifting device where a
cradle is positioned under each rear wheel as indicated below.
Towing by Another Vehicle
WARNING: When the engine is stationary, there will be no power assistance to
the steering or brakes. Therefore be prepared for relatively heavy steering and
the need for greatly increased brake pedal pressure.
The vehicle may be towed short distances by another provided that a speed
of 48 km/h (30 mph) is not exceeded. Do not tow for more than 24km (15
miles). When being towed, the vehicles gear lever, or gear selector lever
(automatic transmission), must be in Neutral or position N with the ignition
key turned to position II to release the steering lock and to render the horn,
indicators and brake lights operational.

F - Owner Maintenance
1-F-43
Headlight Main Beam Bulb Replacement
1. Lift the bonnet.
2. Turn the lamp rear cap anti-clockwise and release it.
3. Pull off the two electrical leads from the headlight bulb connectors.
4. Pinch the bulb retaining clip and release it.
5. Withdraw the headlight bulb, noting the bulb orientation.
6. Hold the new bulb in a clean cloth or paper towel. Orientate the new
bulb correctly in the headlight bulb holder and secure it with the spring
clip.
7. Connect the two electrical leads.
8. Refit and secure the lamp rear cover.

F - Owner Maintenance
1-F-59 When returning the car to normal service, set the tyre pressures to normal
specification before driving on the road.
Extended Storage
For storage periods exceeding six months the following additional measures
are recommended;
Run the car until there is as small a quantity of fuel in the tank as is practical
for storage purposes.
Caution: Do Not Drain The Fuel System
Add Engine Oil to the remaining fuel in the tank to ensure a concentration
of 2% (i.e. 20ml per 1 litre of fuel) and then run the engine for not less than
ten minutes to circulate the mixture thoroughly through the entire fuel
system.
Inspect the rubber connections of the cooling system and have them
renewed if necessary.
Wash the bodywork of the car thoroughly and repair any paint
blisters or patches of rust in order to prevent any further deterioration.
Apply a suitable polish.
Clean the carpets and upholstery thoroughly. Dust them with an
anti-moth powder and store in a dry place. Treat all leather upholstery
with an appropriate leather conditioner.
If the storage building is dry leave the car windows slightly open. If
there is any tendency towards dampness close the car doors and
windows and place an anti-moisture compound such as Silica desiccant
bags in an open metal container inside the car.
Cover the car with it's fabric cover.