2003 ASTON MARTIN DB AR1 Q oil

F - Owner Maintenance
1-F-7
Engine Oil Level Check
When checking engine oil level, the car should be on level ground. If the
engine has been running immediately prior to the check, wait several
minutes after stopping the engine for the oil to drain back into the sump. The
dipstick (1) (which should be wiped clean before checking the oil level) is
located on the left-hand side of the engine. The oil level should be
maintained at the 'Max' dipstick mark.
Approximately one litre is required to bring the level from Min to Max. The
recommended engine oil should be added through the oil filler (3). Do not
overfill. Replace the filler cap securely.
WARNING: Running the engine with insufficient oil can cause serious damage.
To avoid personal injury and before working in or near the engine compartment,
switch off the engine and let it cool. Engine components are hot and may cause
severe burns. See also the warnings given in SERVICING PRECAUTIONS.

F - Owner Maintenance
1-F-31
WARNINGS:
To help avoid personal injury, do not use open flame, smoke, or cause an electric
spark when checking the battery, as gas generated by the battery is flammable
and can explode. Always shield your eyes and avoid leaning over the battery.
Do not ingest battery acid or fumes. If battery acid is ingested, drink large
quantities of water or milk followed by milk of magnesia, beaten egg or vegetable
oil. Call for medical assistance immediately.
Do not let battery acid come into contact with skin, eyes, hair, fabric or painted
surfaces. A solution of warm soapy water and baking soda may help neutralise
acid.
Used batteries contain sulphuric acid, lead and other potentially hazardous
materials. Dispose of unwanted batteries in authorised waste disposal facilities.
DO NOT discard unwanted batteries in household waste.
Quiescent Battery Drain
Any power drain from a battery after the ignition is switched off is referred
to as 'quiescent battery drain'. Your DB AR1, in common with many modern,
high technology motor cars, contains electronic circuits and sub-systems
which must be left activated at all times. For example, the clock, security
systems and in-car entertainment system continue to drain battery power
even with the ignition switched off. This quiescent drain will discharge a fully
charged new battery in approximately 30 days unless recharged by normal
engine running or an independent battery charger.
It is therefore vital that, when leaving your car unused for extended
periods, you use the battery disconnect switch to minimise quiescent
drain and that you use the battery conditioner to maintain battery
charge level.

F - Owner Maintenance
1-F-39
Fuse Lists
Passenger Footwell Fusebox - Right Hand
F1 5A Passive Anti-Theft Module
F2 20A Cigar Lighter
F3 10A Diagnostic Sockets, Radio, Air Conditioning, Driver's
Door Mirror and Window
F4 5A Seat Switches and Heaters
F5 10A Indicator Flasher
F6 10A Ignition Coils 1-6
F7 10A Interior Lamp Cluster
F8 10A Ignition Coils 7-12
F9 20A RHS Seat Heater Relay, RHS Seat Module
F10 10A Dimmer, Passive Anti-Theft Module, Radio
F11 10A Door Mirrors
F12 5A Diagnostic Sockets
F13 25A Not used
F14 10A Hazard Flasher Unit
F15 20A Wiper Logic Module and Wiper Stalk
F16 30A ABS Control Unit
F17 20A Wiper Motor, Logic Module and Wiper Stalk
F18 30A ABS Control Unit
F19 10A Air Conditioning LH Blower Motor
F20 5A Gearshift Interlock Module, Traction Control Switch,
Interior, Map & Courtesy Lamps
F21 10A Air Conditioning RH Blower Motor
F22 10A Powertrain and Transmission control Modules - Keep
Alive Memory

F - Owner Maintenance
1-F-56
Upholstery, Carpets and Seats
The seats and soft trimmed components of DB AR1 are covered in Natural
Leather Hide and Alcantara. The Natural Leather Hide is supplied by Bridge
of Weir, Scotland.
In general, this natural leather upholstery requires little attention. The seats
should be brushed with a soft brush from time to time and may be cleaned
occasionally with a cloth damped in soap and water. DO NOT use
detergents, quick cleansers or furniture polishes.
Several times a year, a leather conditioner or preservative should be used.
Appropriate care materials are contained in the 'Bridge of Weir Leather Care
Kit', obtainable from your Aston Martin Dealer.
Alcantara trim and seat panels may be brushed with a soft brush. Stains from
water based substances such as coffee, tea or soft drinks should be cleaned
as soon as possible with mild soap and water. Please consult your dealer for
instructions on the removal of more difficult stains such as oil, grease or
ballpoint Ink.
Carpets should be cleaned regularly with a vacuum cleaner. Any stains or
grease marks should be removed with a good quality solvent suitable for use
on carpets.
WARNING: Fumes from cleaning solvents may be dangerous in confined spaces.
Make sure that the car is well ventilated and follow the manufacturer's printed
instructions when using these products.

F - Owner Maintenance
1-F-58
Storing the Car - Recommendations
Note: These recommendations apply to new and pre-owned cars either in
Dealer or customer ownership.
When ever the car is not in use always cover the car with it's fabric cover.
If the vehicle is not to be used for periods up to six months it should be stored
in a dry, well ventilated building.
Drive the car for a sufficient distance to warm the oil in the engine, torque
convertor, transmission and final drive unit; this ensures complete lubrication
of the internal components.
Check the engine coolant level. Top up if necessary with the correct
antifreeze/water solution.
In order to take the weight off the tyres, raise the car with a jack and place
supports under the front and rear suspension.
If the vehicle is not raised from the ground, increase the tyre pressures to 3.4
bar 340 kpa 50 psi. Cover the tyres to exclude any light. Rotate the wheels
1/4 turn every month to avoid tyre flat spots.
The battery should be removed and cleaned. Fully charge the battery on a
trickle charger and recharge once a month.
Once a month
Reconnect the battery and ventilate the storage area. Start and run the
engine until fully warmed up. Check that there are no fluid leaks. Check
and correct the tyre pressures if necessary.
Run the Air Conditioning system to keep the internal parts of the Air
Conditioning system lubricated.

F - Owner Maintenance
1-F-59 When returning the car to normal service, set the tyre pressures to normal
specification before driving on the road.
Extended Storage
For storage periods exceeding six months the following additional measures
are recommended;
Run the car until there is as small a quantity of fuel in the tank as is practical
for storage purposes.
Caution: Do Not Drain The Fuel System
Add Engine Oil to the remaining fuel in the tank to ensure a concentration
of 2% (i.e. 20ml per 1 litre of fuel) and then run the engine for not less than
ten minutes to circulate the mixture thoroughly through the entire fuel
system.
Inspect the rubber connections of the cooling system and have them
renewed if necessary.
Wash the bodywork of the car thoroughly and repair any paint
blisters or patches of rust in order to prevent any further deterioration.
Apply a suitable polish.
Clean the carpets and upholstery thoroughly. Dust them with an
anti-moth powder and store in a dry place. Treat all leather upholstery
with an appropriate leather conditioner.
If the storage building is dry leave the car windows slightly open. If
there is any tendency towards dampness close the car doors and
windows and place an anti-moisture compound such as Silica desiccant
bags in an open metal container inside the car.
Cover the car with it's fabric cover.

F - Owner Maintenance
1-F-60
Recommissioning After Storage
Provided that the car has been stored in accordance with the recommended
procedure, the following points only should require attention before using
the car on the road.
Check the tyre pressures, inflate if necessary and lower the car to the ground.
Fully charge and refit the battery. Reset the clock and electric windows.
Drain the engine sump and final drive unit, fit a new engine oil filter element,
then refill with the approved oils. Check the coolant level and if necessary
top up with the correct antifreeze/water solution.
Check all fluid levels and top-up as necessary. Fill the fuel tank
Caution: Starting the engine without sufficient lubrication can cause serious engine
damage. Take care to establish engine oil pressure as directed in the following steps
before allowing the engine to start.
Press and hold the accelerator hard to the floor (kickdown switch actuated).
This will temporarily inhibit the fuel injectors during cranking. Turn on the
ignition. Press and hold the starter button to crank the engine until normal
oil pressure is indicated on the oil pressure gauge. Release the starter button
and the accelerator pedal.
Start the engine normally and check that the oil pressure and ignition
warning lights go out as the engine starts indicating correct oil pressure and
battery charging. Raise the bonnet and check for leaks of fuel, oil and
coolant.
Finally, check the operation of all instruments, lights and accessories.

G - Specifications
1-G-2
Body
Two door Roadster with 2+0 seating.
Steel underframe and body panels. Steel front wings, boot lid, sills and front
and rear bumper aprons. Steel doors, bonnet inner, boot inner and rear
quarters. Side impact protection in the doors.
Engine
All alloy, quad overhead cam 48 valve V12. 5935 cc. Compression ratio
10.3:1.
Twin EECV engine management systems with multi-point sequential fuel
injection and 'Coil on Plug' Ignition System.
Fuel 95 RON Unleaded or 98 RON Super Unleaded.
(USA - Premium Unleaded). 2 in-tank fuel pumps.
Emission control 4 Oxygen sensors / three-way catalytic convertors,
Exhaust gas recirculation, Evaporative loss purge
Bore 89.0mm
Stroke 79.5mm
Spark Plugs NGK - PTR6E-13
Spark Plug Gap 1.3 ± 0.1mm
Lubrication system Wet sump pressurised lubrication
Alternator Denso L3BHE 120A
Voltage Regulation 13.8V ±0.5V @ 20°C
Battery Varta 90AH
(Manual) (Automatic)
Max Power 324 kW (435 bhp) 309kW (420 bhp)
@ 6000 rpm @ 6000 rpm
Max Torque 556 Nm (410 lb/ft) 542 Nm (400 lb/ft)