2003 Acura RSX lock

Î
Îit
only helps with steering control
during braking. You should always
maintain a saf e f ollowing distance
f rom other vehicles.
such as trying to take a
corner too f ast or making a sudden
lane change. Always drive at a safe,
prudent speed f or the road and
weather conditions.
Always steer moderately
when you are braking hard. Severe
or sharp steering wheel movement
can still cause your car to veer into
oncoming traffic or off the road. on loose or
uneven surf aces, such as gravel or
snow, than a vehicle without anti-
lock. Slow down and allow a greater
distance between vehicles under
those conditions.
The ABS is self -checking. If anything
goes wrong, the ABS indicator on
the instrument panel comes on (see
page ). This means the anti-lock
f unction of the braking system has
shut down. The brakes still work like
a conventional system without anti-
lock, providing normal stopping
ability. You should have the dealer
inspect your car as soon as possible.61
Import ant Saf et y Reminders
A BS Indicat or
A BS does not reduce the time or
distance it takes to stop the car;
A BS will not prevent a skid that
results f rom changing direction
abruptly,
A BS cannot prevent a loss of
stability.A vehicle with A BS may require a
longer distance to stop
The Braking System
Driving183
ABS INDICATOR
U.S. indicator shown

µCheck your tires
f requently f or wear and proper
pressure. Both are important in
preventing ‘‘hydroplaning’’ (loss of
traction on a wet surface). In the
winter, mount snow tires on all f our
wheels f or the best handling.
Watch road conditions caref ully,
they can change f rom moment to
moment. Wet leaves can be as slip-
pery as ice. ‘‘Clear’’ roads can have
patches of ice. Driving conditions
can be very hazardous when the
outside temperature is near f reezing.
The road surf ace can become
covered with areas of water puddles
mixed with areas of ice, so your
traction can change without warning.
Be caref ul when downshif ting. If
traction is low, you can lock up the
drive wheels f or a moment and cause
askid. Be very cautious when passing, or
beingpassedbyothervehicles.The
spray f rom large vehicles reduces
your visibility, and the wind buf f eting
can cause you to lose control.
Traction
Driving in Bad Weather
Driving185

µ
Î
Ì
ÌÌÎ
Ì
Maint enance200
Service at the indicated distance or time whichever comes first. miles x 1,000
km x 1,000
months
At 120,000 miles (192,000 km) or 10 years,
then every 60,000 miles (96,000 km) or 5 years
Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy
Every 110,000 miles (176,000 km)
Service the following items at the recommended intervals.
See information on maintenance and emissions warranty, last column, page . Replace every 5,000 miles (8,000 km) or 6 months
Check oil and coolant at each fuel stop
See dust and pollen filter on page for replacement information under special driving conditions. 10
16
20
3230
4840
6450
8060
9670
112 80
128 90
144 100
160110
176120
192
Every 160,000 miles (256,000 km) or 8 years Every 3 years (independent of mileage)
Check engine oil and coolant
Replace engine oil
Rotate tires (Check tire inflation and condition at least once per month)
Replace engine oil filter
Inspect front and rear brakes
Lubricate all hinges, locks, and latches
Visually inspect the following items:
Tie rod ends, steering gear box and boots, suspension components
Driveshaft boots
Check parking brake adjustment
Visually inspect the following items: Brake hoses and lines (including ABS)
All fluid levels and condition of fluidsExhaust system, fuel lines and connections
Lights and controls, vehicle underbody
Inspect and adjust drive belts
Replace dust and pollen filter
Replace transmission fluid
Clean or replace air cleaner element
Replace spark plugs
Inspect valve clearance Inspect idle speed
Replace engine coolant
Replace brake fluid 24
4872
12 3660
1: : 197
M/T
A/T
232
Clean every 15,000 miles (24,000 km), and replace every 30,000 miles (48,000 km) (Use normal schedule except in dusty conditions)
1
Maintenance Schedule for Severe Conditions

µµ
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ì
Ì
Î
CONT INUED
Maint enance201
U.S. Owners
Canadian Owners A, B, C, D
A
B
C
D
Refer to page to determine which schedule to use.
Use the Maintenance Schedule for Severe Conditions.
5,000 mi/8,000 km/6 mos
10,000 mi/16,000 km/1 yr
15,000 mi/24,000 km
15,000 mi/24,000 km/1-½ yrs
20,000 mi/32,000 km/1 yr
25,000 mi/40,000 km/2 yrs
30,000 mi/48,000 km
30,000 mi/48,000 km/2 yrs
35,000 mi/56,000 km/2-½ yrs
40,000 mi/64,000 km/2 yrs
3yrs
45,000 mi/72,000 km
45,000 mi/72,000 km/3 yrs
50,000 mi/80,000 km/3 yrs
55,000 mi/88,000 km/3-½ yrs
60,000 mi/96,000 km
60,000 mi/96,000 km/3 yrs
65,000 mi/104,000 km/4 yrs
70,000 mi/112,000 km/4 yrs
75,000 mi/120,000 km
75,000 mi/120,000 km/4-½ yrs
80,000 mi/128,000 km/4 yrs
85,000 mi/136,000 km/5 yrs
90,000 mi/144,000 km
90,000 mi/144,000 km/5 yrs Do items in A.
Do items in A, B.
Clean air cleaner element (independent of
time).
Do items in A.
DoitemsinA,B,C.
Do items in A. Replace air cleaner element (independent of
time).
DoitemsinA,B,D.
Do items in A.
DoitemsinA,B,C. Replace brake fluid (independent of mileage).
Clean air cleaner element (independent of
time).
Do items in A.
Do items in A, B.
Do items in A. Replace air cleaner element (independent of
time). Replace transmission fluid (M/T, A/T).
DoitemsinA,B,C,D.
Do items in A.
Do items in A, B. Clean air cleaner element (independent of
time).
Do items in A.
DoitemsinA,B,C.
Do items in A. Replace air cleaner element (independent of
time). Replace transmission fluid (A/T).
DoitemsinA,B,D.
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time.
Replace engine oil.
Inspect front and rear brakes.
Rotate tires (follow pattern on page238).
Lubricate all hinges, locks, and latches.
Replace engine oil filter.
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Check parking brake adjustment.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks. Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Inspect and adjust drive belts.
Replace dust and pollen filter.
196
1
Maintenance Schedule for Severe Conditions (listed by distance/time)

Make sure the engine and
radiator are cool.
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Remove the radiator cap by
pushing down and turning
counterclockwise.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents.
Pourthecoolantslowlyand
caref ully so you do not spill. Clean
up any spills immediately. Spilled
coolant could damage components
in the engine compartment.
Put the radiator cap back on.
Tighten it f ully. 6.
5. 4.
2.
3. 1.
Cooling Syst em
Maint enance213
RADIATOR CAP
RESERVE TANK

A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently and have
the system inspected as soon as
possible.
Always use Honda Power Steering
Fluid. If it is not available, you may
use another power steering f luid as
an emergency replacement.
However, continued use can cause
increased wear and poor steering in
cold weather. Have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
Check the level when the engine is
cold. Look at the side of the
reservoir. The f luid should be
between the UPPER LEVEL and
LOWER LEVEL. If it is below the
LOWER LEVEL, add power steering
f luid to the UPPER LEVEL.
Power Steering
Maint enance221
UPPER LEVEL LOWER LEVEL
T urning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.
Do not spill the power steering f luid
over the body, auto-tensioner, drive
belt and pulleys.
If spilled accidentally, wipe of f any
f luid completely.

Torque the spark plug. (If you do
not have a torque wrench, tighten
the spark plug two-thirds of a turn
after it contacts the cylinder head.)
Tightening torque:
Use a wrench to remove the bolt
holding the ignition coil. Pull the
ignition coil up slightly.
Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
Put the new spark plug into the
socket, then screw it into the hole.
Screw it in by hand so you do not
crossthread it. Remove the spark plug with
a f ive-eighths inch (16 mm) spark
plug socket. Remove the ignition coil.
6. 5.
4. 3.
7.8.
(RSX and Premium models)
(Type-S)
CONT INUED
Spark Plugs
Maint enance225
CONNECTOR
IGNITION
COIL LOCK TAB
13 lbf·ft (18 N·m , 1.8 kgf·m)
18 lbf·ft (25 N·m , 2.5 kgf·m)

Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or if they leave streaks
and unwiped areas when used.Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold the lock tab in
while you push the blade assembly
toward the base of the arm.
To replace a blade (front or rear):
Raise the wiper arm of f the
windshield or rear window. 2.
1.
CONT INUED
Wiper Blades
Maint enance229
WIPER ARMS
LOCK TAB