Page 67 of 420
These labels are in the locations
shown. They warn you of potential
hazards that could cause serious
injury. Read these labels caref ully.
If a label comes of f or becomes hard
to read, contact your Acura dealer
f or a replacement.U.S. models onlyU.S. models
Canadian models
Saf ety L abels
Driver and Passenger Saf ety63
RADIATOR CAP SUN VISOR
HOOD DASHBOARD
BATTERY LABEL
Page 76 of 420

This light normally comes on f or a
f ew seconds when you turn the
ignition switch ON (II). If this light
comes on at any other time, there is
a problem in the 4WD system. Take
the vehicle to your dealer to have it
checked.
This indicator monitors the
temperature of the automatic
transmission f luid. The indicator
should come on f or a f ew seconds
when you turn the ignition switch
ON (II). If it comes on while driving,
it indicates the transmission f luid
temperature is too high. Pull to the
side of the road when it is saf e, shif t
to Park, and let the engine idle until
the indicator goes out.
If the indicator blinks while driving,
pull to the side of the road when it is
saf e, shif t to Park, and let the engine
idle until the indicator goes out.
This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the
or position. This indicator
will come on when the light switch is
in AUTO and the lights turn on
automatically. If you turn the ignition
switch to ACCESSORY (I) or LOCK
(0) without turning of f the light
switch, this indicator will remain on.
A reminder chime will also sound
when you open the driver’s door.On cars with automatic lighting (see
page ) 80
Indicator L ights
Inst rument s and Cont rols
VTM-4 Indicator
A/T Temperature
Indicator
Lights On Indicator
(U.S. models only)
72
Continuing to drive with the A/T
Temperature indicator lit may cause
serious damage to the transmission. Continuing to drive with the VTM-4
indicator blinking may cause serious
damage to the system.
Page 84 of 420

To f lash the high beams, pull the
turn signal lever back lightly, then
release it. The high beams will come
on and go off.
The high beams will stay on f or as
long as you hold the lever back, no
matter what position the headlight
switch is in.The Automatic Lighting f eature
turns on the headlights, all other
exterior lights, and the instrument
panel lights when it senses low
ambient light.To turn on automatic lighting, turn
the light switch to AUTO at any time.
The lights will come on automatically
when the outside light level becomes
low (at dusk, f or example). The
Lights On indicator comes on as a
reminder. The lights and indicator
will turn of f automatically when the
system senses high ambient light.
The lights will remain on when you
turn of f the ignition switch. They will
turn of f automatically when you open
the driver’s door. To turn them on
again, either turn the ignition switch
to ON (II) or turn the light switch to
.
On Touring Model
Controls Near the Steering Wheel
Inst rument s and Cont rols
Automatic Lighting
80
AUTO POSITION
Page 86 of 420
The dial on the instrument panel
controls the brightness of the
instrument panel lights. Turn the dial
to adjust the brightness.
The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights-on
reminder chime.
With the headlight switch off, the
high beam headlights come on with
reduced brightness when you turn
the ignition switch to ON (II) and
release the parking brake. They
remain on until you turn the ignition
of f , even if you set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.Instrument Panel Brightness
Daytime Running L ights
(Canadian Models)
Controls Near the Steering Wheel
Inst rument s and Cont rols82
INSTRUMENT PANEL BRIGHTNESS
CONTROL DIAL
Page 88 of 420
If you turn the INT TIME ring to the
shortest delay, the wipers will
change from intermittent to low
speed operation when vehicle speed
exceeds 12 mph (20 km/h).
In intermittent, the wipers operate
every f ew seconds. You can vary
how of ten the wipers sweep the
windshield by turning the INT TIME
ring next to the rotary switch. The
sweep interval will change slightly
with speed; getting shorter as you
drive f aster. In low speed and high
speed the wipers run continuously. To operate the wipers in mist mode,
push the control lever down. The
wipers run at high speed until you
release the lever. This gives you a
quick way to clear the windshield.
Controls Near the Steering Wheel
Inst rument s and Cont rols84
Page 100 of 420

Panic mode allows you to remotely
activate your vehicle’s horn and
lights to attract attention. When
activated, the horn will sound, and
the headlights, parking lights, side
marker lights, taillights and
instrument panel lights will f lash f or
about 30 seconds. To activate panic
mode,pressandholdthePANIC
button f or about one second.When the remote transmitter’s
battery begins to get weak, it may
take several pushes on the button to
lock or unlock the doors and the
tailgate, and the LED will get dim.
Replace the battery as soon as
possible.
Battery type: CR2025To replace the battery, place a cloth
on the edge of the transmitter and
remove the upper half by carefully
prying on the edge with a small f lat-
tip screwdriver.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
key is in the ON (II) position.
Panic Mode
Replacing t he Bat t ery
Keys and Locks
Inst rument s and Cont rols96
Page 102 of 420

Theremotetransmitterswillalso
activate the Driving Position
Memory System (see page ).
When you open the driver’s door
after unlocking it with the remote
transmitter, you will hear a beep.
The driver’s seat and outside mirrors
move to the positions stored in that
memory location. You will hear two
beeps when the movement iscomplete.
If the seat and mirrors are already in
the proper positions, you will hear
three beeps when you open the door.
The driving position memory
activated (Memory 1, Memory 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in the
memory that is activated by the
transmitter you normally carry.
To turn it back on, repeat this
procedure. The LED will come on
f or one second to indicate the
f eature has been turned on. You can turn the driving position
memory activation off and on. To
turn it of f , press and hold the LOCK
and UNLOCK buttons at the same
time f or about one second. The LED
in the remote transmitter will blink
twice. Then release the buttons.
118
On Touring Model
Recalling a Memorized Driving
Position
Keys and Locks
Inst rument s and Cont rols98
With Memory 1 With Memory 2
Page 105 of 420

µ
Pull up or push down on the f ront of
the switch to move the seat bottom’s
f ront edge up or down. Pull up or
push down on the rear of the switch
to move the rear of the seat bottom
up or down.
Push the horizontal switch forward
or backward to move the seat
forward or backward. The long horizontal switch adjusts
the seat bottom in several directions.
The short vertical switch adjusts the
seat-back angle.
Your Acura has power adjustments
f or the driver’s seat. The two power
seat adjustment switches are on the
outside edge of the seat bottom.
You can adjust the seat with the
ignition switch in any position. Make
all seat adjustments bef ore you start
driving. The Touring package also has power
adjustments f or the f ront passenger’s
seat. The MDX without the Touring
package has manual adjustments.
Thesecondandthirdrowseatsin
both models have manual
adjustments.
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs. 12 13
CONT INUED
Power Seat A djustments
Seats
Inst rument s and Cont rols101