INSTRUMENT AND CONTROL FUNCTIONS
3-4
3
EAU04559
Engine speed indicator light
The electrical circuit of the indicator
light can be checked according to the
following procedure.
1. Turn the key to “ON”.
2. If the indicator light does not come
on for a few seconds, then go off,
have a Yamaha dealer check the
electrical circuit. (See pages 3-8–
3-10 for a detailed explanation of
the function of this indicator light
and on how to set it.)
EAU04515
Coolant temperature warning light
“”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and allow
the engine to cool.
The electrical circuit of the warning light
can be checked according to the fol-
lowing procedure.
1. Turn the key to “ON”.
2. If the warning light does not come
on for a few seconds, then go off,
have a Yamaha dealer check the
electrical circuit.
EC000002
CAUTION:_ Do not operate the engine if it is
overheated. _
1. Engine speed indicator light
2. Coolant temperature warning light “”
3. Coolant temperature display
U5PWE0.book Page 4 Friday, December 7, 2001 5:14 PM
INSTRUMENT AND CONTROL FUNCTIONS
3-5
3
CB-25E
Coolant
temperatureDisplay Conditions What to do0–39 °C Message “LO” is
displayed.OK. Go ahead with riding.
40–116 °C Temperature is
displayed.OK. Go ahead with riding.
117–139 °C Temperature flashes.
Warning light comes on.Stop the motorcycle and allow it to
idle until the coolant temperature
goes down.
If the temperature does not go
down, stop the engine. (See the
“Engine overheating” section on
page 6-46 for further instructions.)
Above 140 °C Message “HI” flashes.
Warning light comes on.Stop the engine and allow it to cool.
(See the “Engine overheating” sec-
tion on page 6-46 for further in-
structions.)
U5PWE0.book Page 5 Friday, December 7, 2001 5:14 PM
5-1
5
EAU00372
5-OPERATION AND IMPORTANT RIDING POINTS
EAU00373
WARNING
_
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly un-
derstand.
Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
_
EAU04560
Starting a cold engine In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EW000054
WARNING
_
Before starting the engine,
check the function of the igni-
tion circuit cut-off system ac-
cording to the procedure
described on page 3-26.
Never ride with the sidestand
down.
_1. Turn the key to “ON” and make
sure that the engine stop switch is
set to “”.
ECA00132
CAUTION:_ The following warning lights and in-
dicator light should come on for a
few seconds, then go off.
Oil level warning light
Fuel level warning light
Coolant temperature warning
light
Engine speed indicator light
Engine trouble warning light
If a warning or indicator light does
not go off, see pages 3-2–3-5 for the
corresponding warning and indica-
tor light circuit check.
_2. Shift the transmission into the neu-
tral position.NOTE:_ When the transmission is in the neutral
position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical cir-
cuit. _3. Start the engine by pushing the
start switch.
U5PWE0.book Page 1 Friday, December 7, 2001 5:14 PM
PERIODIC MAINTENANCE AND MINOR REPAIR
6-12
6 10. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off
and check for the cause.
NOTE:_ After the engine is started, the engine
oil level warning light should go off if the
oil level is sufficient. _
EC000067
CAUTION:_ If the oil level warning light flickers
or remains on, immediately turn the
engine off and have a Yamaha deal-
er check the vehicle. _11. Turn the engine off, and then
check the oil level and correct it if
necessary.
12. Install the cowling.
EAU04298
Coolant The coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
To check the coolant level
1. Place the motorcycle on a level
surface and hold it in an upright
position.
NOTE:_
The coolant level must be checked
on a cold engine since the level
varies with engine temperature.
Make sure that the motorcycle is
positioned straight up when
checking the coolant level. A slight
tilt to the side can result in a false
reading.
_2. Check the coolant level in the
coolant reservoir.NOTE:_ The coolant should be between the
minimum and maximum level marks. _3. If the coolant is at or below the min-
imum level mark, remove panel A
(See page 6-7 for panel removal
and installation procedures.), re-
move the reservoir cap, add cool-
ant to the maximum level mark,
and then install the reservoir cap
and the panel.
1. Maximum level mark
2. Minimum level mark
Coolant reservoir capacity:
0.24 L
U5PWE0.book Page 12 Friday, December 7, 2001 5:14 PM
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
6
EC000080
CAUTION:_
If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.
If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the engine may not be
sufficiently cooled and the cool-
ing system will not be protected
against frost and corrosion.
If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness of
the coolant will be reduced.
_
EW000067
WARNING
_ Never attempt to remove the radia-
tor cap when the engine is hot. _
NOTE:_
The radiator fan is automatically
switched on or off according to the
coolant temperature in the radia-
tor.
If the engine overheats, see page
6-46 for further instructions.
_
EAU04524
To change the coolant
1. Place the motorcycle on a level
surface and let the engine cool if
necessary.
2. Remove cowlings A and B, and
panel A. (See pages 6-5–6-7 for
cowling and panel removal and in-
stallation procedures.)
3. Place a container under the en-
gine to collect the used coolant.
4. Remove the radiator cap and cool-
ant reservoir cap.
EW000067
WARNING
_ Never attempt to remove the radia-
tor cap when the engine is hot. __1. Coolant reservoir cap
2. Radiator cap
U5PWE0.book Page 13 Friday, December 7, 2001 5:14 PM
INDEXAAir filter element, replacing ..................... 6-16
Anti-theft alarm ...................................... 3-11BBattery ................................................... 6-33
Brake and clutch levers,
checking and lubricating ...................... 6-30
Brake fluid, changing ............................. 6-27
Brake fluid level, checking...................... 6-26
Brake lever............................................. 3-13
Brake light switch (rear), adjusting ......... 6-24
Brake pads, checking............................. 6-25
Brake pedal............................................ 3-14
Brake pedal, lubricating.......................... 6-31
Brake pedal position, adjusting .............. 6-24CCables, checking and lubricating............ 6-29
Care.........................................................7-1
Catalytic converter ................................. 3-16
Clutch lever ............................................ 3-13
Clutch lever free play, adjusting ............. 6-23
Conversion table ......................................8-5
Coolant .................................................. 6-12
Changing .......................................... 6-13
Checking .......................................... 6-12
Coolant temperature warning light............3-4
Cowlings and panels,
removing and installing ..........................6-5
DDimmer switch ....................................... 3-11
Drive chain, lubricating .......................... 6-29
Drive chain slack ................................... 6-27
Adjusting .......................................... 6-28
Checking .......................................... 6-27EEngine break-in ....................................... 5-3
Engine oil and oil filter cartridge ............... 6-9
Engine speed indicator light..................... 3-4
Engine stop switch................................. 3-12
Engine trouble warning light .................... 3-3
EXUP system ........................................ 3-24FFront fork, adjusting ............................... 3-19
Front fork, checking ............................... 6-31
Fuel ....................................................... 3-15
Fuel consumption, tips for reducing ......... 5-3
Fuel level warning light ............................ 3-2
Fuel tank breather hose ......................... 3-16
Fuel tank cap ......................................... 3-14
Fuses, replacing .................................... 6-35HHandlebar switches ............................... 3-11
Headlight bulb, replacing ....................... 6-36
Helmet holders ...................................... 3-18
High beam indicator light ......................... 3-3
Horn switch ........................................... 3-12
IIdentification numbers ..............................9-1
Idling speed, adjusting ...........................6-18
Ignition circuit cut-off system ..................3-25
Indicator and warning lights......................3-2KKey identification number .........................9-1LLicense plate light bulb, replacing...........6-38
Light switch .............................................. 3-12
Luggage strap holders ...........................3-23MMain switch/steering lock .........................3-1
Model label ..............................................9-2
Multi-function display................................3-6NNeutral indicator light ...............................3-3OOil level warning light ...............................3-3PParking.....................................................5-4
Part locations ...........................................2-1
Pass switch ............................................3-11
Periodic maintenance and lubrication
chart ......................................................6-2
Pre-operation check list ............................4-1
U5PWE0.book Page 1 Friday, December 7, 2001 5:14 PM