2002 YAMAHA YZ250LC brake

4-40
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE GEARENG
Extent of removal Order Part name Q’ty Remarks
RPIMARY DRIVE GEAR REMOVAL
Preparation for Drain the transmission oil.Refer to “TRANSMISSION OIL REPLACE-
removalMENT“ section in the CHAPTER 3.
Bolt (brake pedal) Shift the brake pedal downward.
Radiator hose 4 Disconnect at water pump side.
Bolt (push rod)
Refer to “CYLINDER HEAD, CYLINDER
AND PISTON” section.
1 Kick starter 1
2 Crankcase cover (right) 1
3 Bolt (Primary drive gear) 1 Only loosening
Refer to “REMOVAL POINTS”.
4 Primary driven gear 1 Refer to “CLUTCH AND PRIMARY
DRIVEN GEAR”section.
5 Primary drive gear 1
6 Thrust plate 1
EC4C0000
KICK AXLE, SHIFT SHAFT AND PRIMARY DRIVE GEAREC4C8000
PRIMARY DRIVE GEAR
1
Extent of removal:1Primary drive gear removal
30 Nm (3.0 m•kg, 22 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
55 Nm (5.5 m•kg, 40 ft•lb)
5NX-9-30-4B 6/7/01 1:56 PM Page 26

34 Nm (3.4 m•kg, 24 ft•lb)
4-60
ENGINE REMOVALENG
Extent of removal Order Part name Q’ty Remarks
ENGINE REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Seat and fuel tankRefer to “SEAT, FUEL TANK AND
SIDE COVERS” section.
Carburetor and carburetor jointRefer to “CARBURETOR AND REED
VALVE” section.
Exhaust pipe and silencer Refer to “EXHAUST PIPE AND
Exhaust pipe stay (rear) SILENCER” section.
Clutch cable Disconnect at engine side.
Radiator Refer to “RADIATOR” section.
Spark plug
Disconnect the CDI magneto lead.
CDI unit
Reservoir tank (rear brake) Refer to “FRONT BRAKE AND REAR
BRAKE” section in the CHAPTER 5.
EC4M0000
ENGINE REMOVAL
w
Support the machine securely so there is no dan-
ger of it falling over.



26 Nm (2.6 m•kg, 19 ft•lb)
69 Nm (6.9 m•kg, 50 ft•lb)
69 Nm (6.9 m•kg, 50 ft•lb)
75 Nm (7.5 m•kg, 54 ft•lb)
8 Nm (0.8 m•kg, 5.8 ft•lb)
85 Nm (8.5 m•kg, 61 ft•lb)
5NX-9-30-4C 6/5/01 4:25 PM Page 22

4-61
ENGINE REMOVALENG
Extent of removal:1Engine removal
Extent of removal Order Part name Q’ty Remarks
1 Chain cover 1
2 Nut (drive sprocket) 1
3 Lock washer 1 Refer to “REMOVAL POINTS”.
4 Drive sprocket 1
5 Clip 1
6 Bolt (brake pedal) 1
7 Brake pedal 1
8 Engine bracket 2
9 Engine mounting bolt 3
10 Pivot shaft 1 Remove completely.
11 Engine 1 Refer to “REMOVAL POINTS”.
1





26 Nm (2.6 m•kg, 19 ft•lb)
69 Nm (6.9 m•kg, 50 ft•lb)
34 Nm (3.4 m•kg, 24 ft•lb)
69 Nm (6.9 m•kg, 50 ft•lb)
75 Nm (7.5 m•kg, 54 ft•lb)
8 Nm (0.8 m•kg, 5.8 ft•lb)
85 Nm (8.5 m•kg, 61 ft•lb)
5NX-9-30-4C 6/5/01 4:25 PM Page 24

4-62
ENGINE REMOVALENG
EC4M3340
Engine removal
NOTE:
Make sure that the couplers, hoses and cables
are disconnected.
1. Lift the engine 1up to the point where the
engine’s mounting front does not contact the
bracket on the frame.
2. Remove the engine 1aslant and upward
while inclining it toward the kick crank side
so that the engine’s mounting top does not
contact the bracket on the frame.
EC4M3000
REMOVAL POINTS
EC4F3100
Drive sprocket
1. Remove:
9Nut (drive sprocket) 1
9Lock washer 2
NOTE:
9Straighten the lock washer tab.
9Loosen the nut while applying the rear brake.
2. Remove:
9Drive sprocket 1
9Drive chain 2
NOTE:
Remove the drive sprocket together with the
drive chain.
5NX-9-30-4C 6/5/01 4:25 PM Page 26

4-63
ENGINE REMOVALENG
EC4M5341
Drive sprocket
1. Install:
9Drive sprocket 1
9Drive chain 2
NOTE:
Install the drive sprocket together with the drive
chain.
EC4M5211
Brake pedal
1. Install:
9Spring 1
9Brake pedal 2
9O-ring 3
9Bolt (brake pedal) 4
9Clip 5
NOTE:
9Apply the lithium soap base grease on the bolt,
O-rings and brake pedal bracket.
9Install the clip with its stopper portion afacing
inward.
EC4M5000
ASSEMBLY AND INSTALLATIONEC4M5123
Engine installation
1. Install:
9Engine 1
Install the engine from right side.
9Pivot shaft 2
9Engine mounting bolt (lower) 3
9Engine mounting bolt (front) 4
9Engine bracket 5
9Bolt (engine bracket) 6
9Engine mounting bolt (upper) 7
NOTE:
Apply the molybdenum disulfide grease on the
pivot shaft.
85 Nm (8.5 m•kg, 61 ft•lb)
69 Nm (6.9 m•kg, 50 ft•lb)
69 Nm (6.9 m•kg, 50 ft•lb)
34 Nm (3.4 m•kg, 24 ft•lb)
69 Nm (6.9 m•kg, 50 ft•lb)
26 Nm (2.6 m•kg, 19 ft•lb)
5NX-9-30-4C 6/5/01 4:25 PM Page 28

4-64
ENGINE REMOVALENG
4. Install:
9Chain guide 1
9Chain cover 2
9Screw (chain cover) 3 2. Install:
9Lock washer 1
9Nut (drive sprocket) 2
NOTE:
Tighten the nut while applying the rear brake.
3. Bend the lock washer tab to lock the nut.
8 Nm (0.8 m•kg, 5.8 ft•lb)
75 Nm (7.5 m•kg, 54 ft•lb)
5NX-9-30-4C 6/5/01 4:25 PM Page 30

5-1
CHASFRONT WHEEL AND REAR WHEEL
Extent of removal Order Part name Q’ty Remarks
FRONT WHEEL REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
1 Hose cover 1
2 Bolt (brake hose holder) 2 Only loosening.
3 Bolt (axle holder) 4 Only loosening.
4 Nut (front wheel axle) 1
5 Front wheel axle 1
6 Front wheel 1
7 Collar 2
8 Oil seal 2
9 Bearing 2 Refer to “REMOVAL POINTS”.
10 Brake disk 1
EC500000
CHASSISEC590000
FRONT WHEEL AND REAR WHEELEC598000
FRONT WHEEL
2
13
3
Extent of removal:1Front wheel removal2Wheel bearing removal3Brake disc removal
w
Support the machine securely so there is no dan-
ger of it falling over.
5
23 Nm (2.3 m•kg, 17 ft•lb)
23 Nm (2.3 m•kg, 17 ft•lb)
105 Nm (10.5 m•kg, 75 ft•lb)
16 Nm (1.6 m•kg, 11 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)12 Nm (1.2 m•kg, 8.7 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
5NX-9-30-5A 6/7/01 2:00 PM Page 2

5-2
CHASFRONT WHEEL AND REAR WHEEL
EC598100
REAR WHEEL
Extent of removal:1Rear wheel removal2Wheel bearing removal3Brake disc removal
Extent of removal Order Part name Q’ty Remarks
REAR WHEEL REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
1 Nut (rear wheel axle) 1
2 Rear wheel axle 1
3 Chain puller 2
4 Rear wheel 1 Refer to “REMOVAL POINTS”.
5 Collar 2
6 Driven sprocket 1
7 Oil seal 2
8 Circlip 1
9 Bearing 2 Refer to “REMOVAL POINTS”.
10 Brake disk 1
2
13
3
w
Support the machine securely so there is no dan-
ger of it falling over.
125 Nm (12.5 m•kg, 90 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
42 Nm (4.2 m•kg, 30 ft•lb)
5NX-9-30-5A 6/7/01 2:00 PM Page 4