2002 YAMAHA YZ125LC oil

2-8
SPECCARACTERISTIQUES D’ENTRETIEN
Article Standard Limite
Roue:
Type de roue avant Roue à rayons…
Type de roue arrière Roue à rayons…
Taille/matériau de jante avant 21 ×1,60/Aluminum…
Taille/matériau de jante arrière 19 ×1,85/Aluminum…
Limite de voile de jante:
Radial…
2,0 mm (0,08 in)
Latéral … 2,0 mm (0,08 in)
Chaîne de transmission:
Type/fabricant DID520DMA2 SDH/DAIDO…
Nombre de maillons 111 maillons+attache…
Flèche de la chaîne 40~50 mm (1,6~2,0 in)…
Longueur de chaîne (10 maillons)…
152,5 mm (6,004 in)
Frein à disque avant:
Dia. extérieur ×épaisseur 250 ×3,0 mm (9,84 ×0,12 in)…
Epaisseur de plaquette 4,4 mm (0,17 in) 1,0 mm (0,04 in)
Dia. intérieur de maître-cylindre 11,0 mm (0,433 in)…
Dia. intérieur de cylindre d’etrier 27,0 mm (1,063 in) ×2…
Type de liquide de frein DOT #4…
Frein à disque arrière:
Dia. extérieur ×épaisseur 245 ×4,0 mm (9,65 ×0,16 in)…
Limite de flèche…
0,15 mm (0,006 in)
Epaisseur de plaquette 6,4 mm (0,25 in) 1,0 mm (0,04 in)
Dia. intérieur de maître-cylindre 12,7 mm (0,500 in)…
Dia. intérieur de cylindre d’etrier 27,0 mm (1,063 in)…
Type de liquide de frein DOT #4…
Levier de frein & pédale de frein:
Position du levier de frein 95 mm (3,74 in)…
Hauteur de la pédale de frein Zéro mm (Zéro in)…
(hauteur au-dessus du haut du repose-pied)
Jeu de levier d’embrayage (côté levier) 8~13 mm (0,31~0,51 in)…
Jeu à la poignée d’accélération 3~5 mm (0,12~0,20 in)…
5NY-9-30-2A 5/24/01 8:03 PM Page 21

2-13
SPECCABLE ROUTING DIAGRAM
EC240000
CABLE ROUTING DIAGRAM
1Brake hose
2Cable guide
3“ENGINE STOP” button lead
4Fuel tank breather hose
5Clamp
6Throttle cable
7Air vent hose (right)
8Air vent hose (left)
9Transmission oil breather hose
0Overflow hose
qYPVS breather hose
wRadiator breather hose
eCDI magneto lead
rWireharnessAPass the throttle cable and
“ENGINE STOP” button lead
into the cable guide. Align
with the cable guide the
front end of the tape on the
throttle cable.
BPass the fuel tank breather
hose between the handlebar
and tension bar, then insert
its end into the hole of the
number plate.
CPass the throttle cable and
“ENGINE STOP” button lead
over the radiator hose.
DClamp the throttle cable,
“ENGINE STOP” button lead
and wireharness to the main
pipe. With the clamp ends
downward, tighten the throttle
cable to the extent that it
moves smoothly.
EClamp the “ENGINE STOP”
button lead (where there is no
protector), wireharness and
throttle cable all together to the
main pipe with the clamp ends
downward.FClamp the CDI magneto lead
on the upper part of
the frame gusset at its
protecting tube.
GClamp the throttle cable and
wireharness to the main pipe.
With the clamp ends downward,
tighten the throttle cable to the
extent that it moves smoothly.
HPass the air vent hose at
the rear of the throttle cable.
IPass the transmission oil
breather hose, air vent hoses
and overflow hose between
the frame and connecting rod.
JPass the radiator breather
hose and YPVS breather hose
outside the engine bracket
and inside the down tube. Then
pass the radiator breather
hose inside the YPVS
breather hose.
KClamp the radiator breather
hose and CDI magneto lead
on the rear of the down-tube.
5NY-9-30-2B 5/23/01 8:03 PM Page 26

2-15
SPECCABLE ROUTING DIAGRAM
1Cable guide
2Radiator breather hose
3Ignition coil
4CDI magneto lead
5Clutch cable
6CDI unit band
7CDI unit
8Wireharness
9High tension cord
0CDI unit bracket
qClampAPass the cluch cable into
the cable guide.
BPass the clutch cable over
the radiator hose.
CPass the wireharness between
the convexites of the CDI unit
band.
DClamp the high tension cord on
the upper part of the frame
gusset at its protecting tube.
EPass the ground lead between
the ignition coil and bracket and
fasten it together with the
ignition coil. Make sure that the
ground lead does not contact
the ignition coil and bracket.
FPass the radiator breather
hose at the rear of the radiator
hose.
GCut the clamp end to be flush
with CDI unit side.HFit the CDI unit band over
the CDI unit bracket till it
stops.
IClamp the wireharness on the
CDI unit with the clamp ends
upward.
5NY-9-30-2B 5/23/01 8:03 PM Page 30

3-1
MAINTENANCE INTERVALS
INSP
ADJ
EC300000
REGULAR INSPECTION AND ADJUSTMENTS
EC310052
MAINTENANCE INTERVALS
The following schedule is intended as a general guide to maintenance and lubrication. Bear in mind
that such factors as weather, terrain, geographical location, and individual usage will alter the required
maintenance and lubrication intervals. If you are a doubt as to what intervals to follow in maintaining
and lubricating your machine, consult your Yamaha dealer.
Item Remarks
PISTON
Inspect and clean
Inspect crack
ReplaceRemove carbon
PISTON RING
InspectCheck ring end gap
Replace
PISTON PIN, SMALL END BEARING
Inspect
Replace
CYLINDER HEAD
Inspect and cleanRemove carbon
RetightenCheck gasket
CYLINDER
Inspect and clean
Inspect score marks
ReplaceInspect wear
YPVS
Inspect and clean
CLUTCHInspect housing, friction
Inspect and adjustplate, clutch plate and
Replacespring
TRANSMISSION
Replace oilYamalube 4 (10W-30) or
InspectSAE 10W-30 SE motor oil
Replace bearing
SHIFT FORK, SHIFT CAM, GUIDE BAR
InspectInspect wear
ROTOR NUT
Retighten
MUFFLER
Inspect
Clean
CRANK
Inspect and clean
CARBURETOR
Inspect, adjust and clean
SPARK PLUG
Inspect and clean
Replace
DRIVE CHAIN Use chain lube
Lubricate, slack, alignmentChain slack: 40~50 mm
Replace(1.6~2.0 in)
After
break-
inEvery
raceEvery
thirdEvery
fifthAs re-
quired
3
5NY-9-30-3A 5/23/01 8:24 PM Page 2

3-2
MAINTENANCE INTERVALS
INSP
ADJ
Item Remarks
COOLING SYSTEM
Check coolant level and leakage
Check radiator cap operation
Replace coolantEvery two years
Inspect hoses
OUTSIDE NUTS AND BOLTS Refer to “STARTING
RetightenAND BREAK-IN” section
in the CHAPTER 1.
AIR FILTER
Clean and lubricateUse foam air-filter oil
Replace
FRAME
Clean and inspect
FUEL TANK, COCK
Clean and inspect
BRAKES
Adjust lever position and pedal height
Lubricate pivot point
Check brake disc surface
Check fluid level and leakage
Retighten brake disc bolts, caliper bolts,

master cylinder bolts and union bolts
Replace pads
Replace brake fluidEvery one year
FRONT FORKS
Inspect and adjust
Replace oilSuspension oil “01”
Replace oil seal
FRONT FORK OIL SEAL AND DUST SEAL
Clean and lubeLithium base grease
REAR SHOCK ABSORBER
(After
Inspect and adjustrain ride)
Lube Molybdenum disulfide grease
Retighten
CHAIN GUARD AND ROLLERS
Inspect
SWINGARM
Inspect, lube and retightenMolybdenum disulfide grease
RELAY ARM, CONNECTING ROD
Inspect, lube and retightenMolybdenum disulfide grease
STEERING HEAD
Inspect free play and retighten
Clean and lubeLithium base grease
Replace bearing
TIRE, WHEELS
Inspect air pressure, wheel run-out,

tire wear and spoke looseness
Retighten sprocket bolt
Inspect bearings
Replace bearings
LubricateLithium base grease
THROTTLE, CONTROL CABLE
Check routing and connectionYamaha cable lube or
LubricateSAE 10W-30 motor oil
After
break-
inEvery
raceEvery
thirdEvery
fifthAs re-
quired
3
5NY-9-30-3A 5/23/01 8:24 PM Page 3

3-3
PROGRAMME D’ENTRETIEN
INSP
ADJ
PartieAprès Chaque Chaque Chaque Si
Remarques
rodage coursetrois- cinquiè- nécessa-
ième me ire
PNEU; ROUES
Contrôler la pression de gonflage,
le voile de roue et l’usure des
66pneus et voir s’il n’y a pas de
rayon détendu
Resserrer les boulons de la roue
66dentée
Contrôler les roulements6
Changer les roulements6
Graisser6
ACCELERATEUR, CABLES DE
COMMANDE
Contrôler le chaminement et le
66branchement
Graisser66
Graisse à base de lithium
Yamaha lube pour câble ou
Huile moteur SAE 10W-30
5NY-9-30-3A 5/23/01 8:24 PM Page 7

3-4
PRE-OPERATION INSPECTION AND MAINTENANCE
INSP
ADJ
EC320000
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation, practice or a race, make sure the machine is in good operating
condition.
Before using this machine, check the following points.
EC321000
GENERAL INSPECTION AND MAINTENANCE
Item Routine Page
Coolant Check that coolant is filled up to the radiator filler cap.
Check the cooling system for leakage.P3-5~9
Fuel Check that a fresh mixture of oil and gasoline is filled in
the fuel tank. Check the fuel line for leakage.P1-12
Transmission oil Check that the oil level is correct. Check the crankcase
for leakage.P3-12~14
Gear shifter and clutch Check that gears can be shifted correctly in order and
that the clutch operates smoothly.P3-9
Throttle grip/Housing Check that the throttle grip operation and free play
are correctly adjusted. Lubricate the throttle grip and P3-10~11
housing, if necessary.
Brakes Check the play of front brake and effect of front and
rear brake.P3-17~23
Chain Check chain slack and alignment. Check that the chain
is lubricated properly.P3-24~26
Wheels Check for excessive wear and tire pressure. Check for
loose spokes and have no excessive play.P3-34~35
Steering Check that the handlebar can be turned smoothly and
have no excessive play.P3-35~36
Front forks and Check that they operate smoothly and there is no oil
rear shock absorber leakage.P3-26~33
Cables (wires) Check that the clutch and throttle cables move smooth-
ly. Check that they are not caught when the handlebars —
are turned or when the front forks travel up and down.
Muffler Check that the muffler is tightly mounted and has no
cracks.P3-15~16
Sprocket Check that the driven sprocket tightening bolt is
not loose.P3-24
Lubrication Check for smooth operation. Lubricate if necessary. P3-37
Bolts and nuts Check the chassis and engine for loose bolts and nuts. P1-16
Lead connectors Check that the CDI magneto, CDI unit, and ignition coil
are connected tightly.P1-6
Settings Is the machine set suitably for the condition of the
racing course and weather or by taking into account the
P7-1~24
results of test runs before racing? Are inspection and
maintenance completely done?
5NY-9-30-3A 5/23/01 8:24 PM Page 14

3-7
INSP
ADJ
RADIATOR CAP INSPECTION
cC
9
Do not mix more than one type of ethyl-
ene glycol antifreeze containing corro-
sion inhibitors for aluminum engine.
9Do not use water containing impurities
or oil.
7. Install:
9Radiator cap
Start the engine and warm it up for a sev-
eral minutes.
8. Check:
9Coolant level
Coolant level low Add coolant.
EC355000
RADIATOR CAP INSPECTION
1. Inspect:
9Seal (radiator cap) 1
9Valve and valve seat 2
Crack/Damage Replace.
Exist fur deposits 3Clean or replace.
Handling notes of coolant:
The coolant is harmful so it should be handled
with special care.
w
9
When coolant splashes to your eye.
Thoroughly wash your eye with water
and see your doctor.
9When coolant splashes to your clothes.
Quickly wash it away with water and then
with soap.
9When coolant is swallowed.
Quickly make him vomit and take him to
a doctor.
5NY-9-30-3A 5/23/01 8:24 PM Page 22