2002 YAMAHA XVS125 ABS

EAU00009
TABLE OF CONTENTS
GIVE SAFETY THE RIGHT OF WAY ................1-1
DESCRIPTION ..................................................2-1
Left view ...........................................................2-1
Right view ........................................................2-2
Controls and instruments .................................2-3
INSTRUMENT AND CONTROL
FUNCTIONS ......................................................3-1
Main switch/steering lock .................................3-1
Indicator and warning lights .............................3-2
Speedometer unit ...........................................3-2
Anti-theft alarm (optional) ................................3-3
Handlebar switches .........................................3-3
Clutch lever ......................................................3-5
Shift pedal ........................................................3-5
Brake lever .......................................................3-5
Brake pedal ......................................................3-6
Fuel tank cap ...................................................3-6
Fuel ..................................................................3-7
Fuel cock .........................................................3-8
Starter (choke) lever ........................................3-9
Helmet holder ..................................................3-9
Adjusting the shock absorber assemblies .......3-9
Sidestand .......................................................3-10
Ignition circuit cut-off system ........................3-11PRE-OPERATION CHECKS .............................4-1
Pre-operation check list ...................................4-1
OPERATION AND IMPORTANT RIDING
POINTS ..............................................................5-1
Starting the engine ...........................................5-1
Starting a warm engine ....................................5-2
Shifting .............................................................5-3
Recommended shift points
(for Switzerland only) .....................................5-3
Tips for reducing fuel consumption .................5-4
Engine break-in ................................................5-4
Parking .............................................................5-5
PERIODIC MAINTENANCE AND
MINOR REPAIR .................................................6-1
Owner’s tool kit ................................................6-1
Periodic maintenance and lubrication chart .....6-2
Removing and installing panels .......................6-5
Checking the spark plugs ................................6-7
Engine oil and oil filter element .......................6-9
Cleaning the air filter element .......................6-12
Adjusting the carburetor .................................6-14
Adjusting the engine idling speed ..................6-14
Adjusting the throttle cable free play ..............6-15
Adjusting the valve clearance .......................6-15
123
456
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 5

2-1
EAU00026
DESCRIPTION
Part locations
2
1. Headlight (page 6-34)
2. Fuel cock (page 3-8)
3. Fuses (page 6-33)
4. Helmet holder (page 3-9)5. Shock absorber spring preload
adjusting ring (page 3-9)
6. Shift pedal (page 3-5)
1234
5
6
Left view
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 8

3-9
INSTRUMENT AND CONTROL FUNCTIONS
3
EAU03839
Starter (choke) lever “1”
Starter (choke) lever
Starting a cold engine requires a rich-
er air-fuel mixture, which is supplied
by the starter (choke).
Move the lever in direction ato turn
on the starter (choke).
Move the lever in direction bto turn
off the starter (choke).
EAU00260
Helmet holder
Helmet holder
To open the helmet holder, insert the
key into the lock, and then turn the
key as shown.
To lock the helmet holder, place it in
the original position, and then remove
the key.
EW000030
wNever ride with a helmet attached
to the helmet holder, since the hel-
met may hit objects, causing loss
of control and possibly an acci-
dent.
EAU00300
Adjusting the shock
absorber assemblies
Shock absorber assemblies, adjusting
Each shock absorber assembly is
equipped with a spring preload
adjusting ring.
EC000015
cCNever attempt to turn an adjusting
mechanism beyond the maximum
or minimum settings.
1
a
b
1
a
1
2
3
4
5
b
a
2
1
1. Starter (choke) lever “1”1. Helmet holder
a Open.1. Shock absorber spring preload
adjusting ring
2. Position indicator
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 19

3-10
EW000040
wAlways adjust both shock
absorber assemblies equally, oth-
erwise poor handling and loss of
stability may result.Adjust the spring preload as follows.
To increase the spring preload and
thereby harden the suspension, turn
the adjusting ring on each shock
absorber assembly in direction a. To
decrease the spring preload and
thereby soften the suspension, turn
the adjusting ring on each shock
absorber assembly in direction b.NOTE:
Align the appropriate notch in the
adjusting ring with the position indica-
tor on the shock absorber.
EAU00330
Sidestand
Sidestand
The sidestand is located on the left
side of the frame. Raise the side-
stand or lower it with your foot while
holding the motorcycle upright.NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system,
which cuts the ignition in certain situ-
ations. (See further down for an
explanation of the ignition circuit cut-
off system.)
EW000044
wThe motorcycle must not be ridden
with the sidestand down, or if the
sidestand cannot be properly
moved up (or does not stay up),
otherwise the sidestand could con-
tact the ground and distract the
operator, resulting in a possible
loss of control. Yamaha’s ignition
circuit cut-off system has been
designed to assist the operator in
fulfilling the responsibility of rais-
ing the sidestand before starting
off. Therefore, check this system
regularly as described below and
have a Yamaha dealer repair it if it
does not function properly.
INSTRUMENT AND CONTROL FUNCTIONS
3
Setting
Minimum (soft) 1
Standard 2
Maximum (hard) 5
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 20

6-4
PERIODIC MAINTENANCE AND MINOR REPAIR
6
EAU03541
NOTE:
8The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
8Hydraulic brake service
9Regularly check and, if necessary, correct the brake fluid level.
9Every two years replace the internal components of the brake master cylinder and caliper, and change the brake
fluid.
9Replace the brake hoses every four years and if cracked or damaged.19
*Shock absorber
assemblies•Check operation and shock absorbers for oil leakage.√√√√
20*Carburetor•Check starter (choke) operation.
•Adjust engine idling speed.√√√√√ √
21 Engine oil•Change.
•Check oil level and vehicle for oil leakage.√√√√√ √
22 Engine oil filter element•Replace.√√√
23*Front and rear brake
switches•Check operation.√√√√√ √
24 Moving parts and cables•Lubricate.√√√√ √
25*Lights, signals and
switches•Check operation.
•Adjust headlight beam.√√√√√ √ NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (× 1,000 km)
ANNUAL
CHECK
1 6 12 18 24
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 34

7-3
MOTORCYCLE CARE AND STORAGE
7 After cleaning
1. Dry the motorcycle with a
chamois or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally
induced discoloring of stainless-
steel exhaust systems can be
removed through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, includ-
ing chrome- and nickel-plated,
surfaces.
5. Use spray oil as a universal
cleaner to remove any remaining
dirt.
6. Touch up minor paint damage
caused by stones, etc.7. Wax all painted surfaces.
8. Let the motorcycle dry complete-
ly before storing or covering it.
EWA00001
w8Make sure that there is no oil
or wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires
with warm water and a mild
detergent.
8Before operating the motorcy-
cle test its braking perfor-
mance and cornering behav-
ior.
ECA00013
cC8Apply spray oil and wax spar-
ingly and make sure to wipe
off any excess.
8Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
8Avoid using abrasive polish-
ing compounds as they will
wear away the paint.NOTE:
Consult a Yamaha dealer for advice
on what products to use.
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 75

8-3
SPECIFICATIONS
8
Maximum load* 183 kg
Air pressure (cold tire)
up to 90 kg load*
Front
175 kPa (1.75 kgf/cm
2, 1.75 bar)
Rear
200 kPa (2.00 kgf/cm
2, 2.00 bar)
90 kg load–maximum
load*
Front
175 kPa (1.75 kgf/cm
2, 1.75 bar)
Rear
200 kPa (2.00 kgf/cm
2, 2.00 bar)
*Total weight of rider, passenger, cargo and accessories
Wheels
Front
Type Spoke wheel
Size 18 ×1.60
Rear
Type Spoke wheel
Size 15 M/C ×MT 3.00
Brakes
Front
Type Single disc brake
Operation Right hand
Fluid DOT 4Rear
Type Drum brake
Operation Right foot
Suspension
Front
Type Telescopic fork
Rear
Type Swingarm
Spring/shock absorber
Front
Type Coil spring/oil damper
Rear
Type Coil spring/oil damper
Wheel travel
Front 140 mm
Rear 100 mm
Electrical system
Ignition system Transistorized coil ignition
(digital)
Charging system
Type A.C. magneto
Standard output 14 V, 23 A @ 5,000 r/min
5JX-28199-E2 honbun 10/11/01 2:14 PM Page 80