2-1
EAU00026
DESCRIPTIONPart locations
2
1. Headlight (page 6-33)
2. Fuel cock (page 3-8)
3. Battery (page 6-31)
4. Owner’s tool kit (page 6-1)
5. Helmet holder (page 3-10)6. Shock absorber spring preload
adjusting nut (page 3-10)
7. Fuse (page 6-32)
8. Starter (choke) knob (page 3-9)
9. Shift pedal (page 3-5)
1
2
3
45
6
7 8 9
Left view
4PT-E7 (English) 6/29/01 9:13 AM Page 10
3-10
INSTRUMENT AND CONTROL FUNCTIONS
3
EAU00260
Helmet holderHelmet holderTo open the helmet holder, insert the
key into the lock, and then turn the
key as shown.
To lock the helmet holder, place it in
the original position, and then remove
the key.
EW000030
wNever ride with a helmet attached
to the helmet holder, since the hel-
met may hit objects, causing loss
of control and possibly an acci-
dent.
1
a
1. Helmet holder
a. Open.
EAU03591
Adjusting the shock
absorber assemblyShock absorber assembly, adjustingThis shock absorber assembly is
equipped with a spring preload
adjusting nut.
EC000015
cCNever attempt to turn an adjusting
mechanism beyond the maximum
or minimum settings.Adjust the spring preload as follows.
1. Loosen the locknut.
a
b
1 2
1. Locknut
2. Adjusting nut
2. To increase the spring preload
and thereby harden the suspen-
sion, turn the adjusting nut in
direction a. To decrease the
spring preload and thereby soft-
en the suspension, turn the
adjusting nut in direction b.NOTE:
The spring preload setting is deter-
mined by measuring distance A,
shown in the illustration. The shorter
distance A is, the lower the spring
preload; the longer distance A is, the
higher the spring preload.
A
4PT-E7 (English) 6/29/01 9:13 AM Page 23
3-11
3. Tighten the locknut to the speci-
fied torque.
EC000018
cCAlways tighten the locknut against
the adjusting nut, and then tighten
the locknut to the specified torque.
EAU00315
wThis shock absorber contains
highly pressurized nitrogen gas.
For proper handling, read and
understand the following informa-
tion before handling the shock
absorber. The manufacturer can-
not be held responsible for proper-
ty damage or personal injury that
may result from improper han-
dling.
8Do not tamper with or attempt
to open the gas cylinder.
8Do not subject the shock
absorber to an open flame or
other high heat sources, other-
wise it may explode due to
excessive gas pressure.
8Do not deform or damage the
gas cylinder in any way, as
this will result in poor damp-
ing performance.
8Always have a Yamaha dealer
service the shock absorber.
EAU00330
SidestandSidestandThe sidestand is located on the left
side of the frame. Raise the side-
stand or lower it with your foot while
holding the motorcycle upright.NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system,
which cuts the ignition in certain situ-
ations. (See further down for an
explanation of the ignition circuit cut-
off system.)
INSTRUMENT AND CONTROL FUNCTIONS
3Spring preload:
Minimum (soft):
Distance A = 1 mm
Standard:
Distance A = 5.5 mm
Maximum (hard):
Distance A = 12 mm
Tightening torque:
Locknut:
42 Nm (4.2 m
0kgf)
4PT-E7 (English) 6/29/01 9:13 AM Page 24
