2002 YAMAHA XT500E wheel torque

6-26
PERIODIC MAINTENANCE AND MINOR REPAIR
6
NOTE:
Make sure that both adjusting plates
are in the same position for proper
wheel alignment.
EC000096
cCImproper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.3. Tighten the axle nut and the
brake caliper bracket bolt to the
specified torques.2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant.
ECA00052
cCDo not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings.
EAU03006
Lubricating the drive chainDrive chain, lubricatingThe drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly
wear out, especially when riding in
dusty or wet areas. Service the drive
chain as follows.
EC000097
cCThe drive chain must be lubricated
after washing the motorcycle or
riding in the rain.1. Clean the drive chain with
kerosene and a small soft brush.
ECA00053
cCTo prevent damaging the O-rings,
do not clean the drive chain with
steam cleaners, high-pressure
washers or inappropriate solvents.
Tightening torques:
Axle nut:
105 Nm (10.5 m0kgf)
Brake caliper bracket bolt:
48 Nm (4.8 m0kgf)
4PT-E7 (English) 6/29/01 9:13 AM Page 63

6-38
PERIODIC MAINTENANCE AND MINOR REPAIR
6
NOTE:
Make sure that there is enough
space between the brake pads
before inserting the brake disc and
that the slot in the speedometer gear
unit fits over the retainer on the fork
leg.3. Install the wheel axle.
4. Lower the front wheel so that it is
on the ground.
5. Tighten the wheel axle to the
specified torque.7. After tightening the holder nuts,
while applying the front brake,
push down on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
8. Connect the speedometer cable.
1
1. Retainer
6. Tighten the axle holder nuts to
the specified tightening torque.
Tighten the upper nuts first and
then lower ones. When tightened
in this sequence, there should be
a gap formed at the bottom of
the axle holder.
2 1
a
1. Upper nut (×2)
2. Lower nut (×2)
a. Gap
Tightening torque:
Wheel axle:
59 Nm (5.9 m0kgf)
Tightening torque:
Axle holder nut:
9 Nm (0.9 m0kgf)
4PT-E7 (English) 6/29/01 9:13 AM Page 75

6-40
PERIODIC MAINTENANCE AND MINOR REPAIR
6 6. Push the wheel forward, and
then remove the drive chain from
the rear sprocket.
NOTE:
The drive chain does not need to be
disassembled in order to remove and
install the wheel.7. Pull the wheel axle out, and then
remove the wheel.
ECA00048
cCDo not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
EAU01136
To install the rear wheelInstall1. Install the drive chain onto the
rear sprocket, and then insert the
wheel axle from the left-hand
side.NOTE:
8Make sure that there is enough
space between the brake pads
before inserting the brake disc
between the brake pads.
8Make sure that the drive chain
adjusting plates are installed with
the punched sides facing to the
outside.2. Install the swingarm end bolts.
3. Adjust the drive chain slack.
(See page 6-25 for drive chain
slack adjustment procedures.)
4. Tighten the axle nut, brake
caliper bracket bolt and
swingarm end bolts to the speci-
fied torques.
4PT-E7 (English) 6/29/01 9:13 AM Page 77