2002 YAMAHA KODIAK 400 oil level

8-39
9. Fill the engine with sufficient oil to reach the
specified level. Install the dipstick and tighten
it.CAUTION:_

Do not put in any chemical additives. En-
gine oil also lubricates the clutch and addi-
tives could cause clutch slippage.


Be sure no foreign material enters the
crankcase.
_
Recommended oil:
See page 10-2.
Oil quantity:
Total amount:
2.6 L
Periodic oil change:
2.3 L
With oil filter replacement:
2.4 L
U5GH62.book Page 39 Monday, August 6, 2001 9:09 AM

8-41
‘1. Final gear oil
2. Final gear case filler bolt
3. Proper level
1. Huile de transmission finale
2. Boulon de remplissage du carter de transmission finale
3. Niveau correct
1. Aceite de la transmisión final
2. Tapa de la caja del filtro
3. Nivel adecuado
10. Start the engine and warm it up for several
minutes. While warming up, check for oil
leakage. If oil leakage is found, stop the en-
gine immediately and check for the cause.
11. Install the panels.
EBU00825
Final gear oil
Final gear oil measurement
1. Place the machine on a level place.
2. Remove the oil filler bolt and check the oil lev-
el. It should be up to the brim of the hole. If
the level is low, add oil to raise it to the proper
level.CAUTION:_ Be sure no foreign material enters the final
gear case. _
U5GH62.book Page 41 Monday, August 6, 2001 9:09 AM

8-43 1. Final gear case cover 2. Bolt (× 2)
1. Couvercle du carter de transmission finale 2. Boulon (× 2)
1. Cubierta del cárter de la transmisión final 2. Perno (× 2)
1. Final gear oil drain bolt
1. Boulon de vidange d’huile de transmission finale
1. Perno de drenaje de aceite del engranaje final
3. Install the oil filler bolt and tighten it to the
specified torque.
Final gear oil replacement
1. Remove the final gear case cover.
2. Place the machine on a level place.
3. Place a container under the final gear case to
collect the used oil.
4. Remove the oil filler bolt and the drain bolt to
drain the oil.
5. Install the drain bolt and tighten it to the spec-
ified torque. Tightening torque:
Oil filler bolt:
23 Nm (2.3 m·kgf)
Tightening torque:
Drain bolt (final gear case):
23 Nm (2.3 m·kgf)
U5GH62.book Page 43 Monday, August 6, 2001 9:09 AM

8-47 1. Differential gear oil
2. Differential gear case oil filler bolt
3. Specified level
1. Huile de différentiel
2. Boulon de remplissage du carter de différentiel
3. Niveau d’huile spécifié
1. Aceite de engranajes del diferencial
2. Perno de relleno de aceite de la caja del diferencial
3. Nivel especificado
EBU00706
Differential gear oil
Differential gear oil measurement
1. Place the machine on a level place.
2. Remove the oil filler bolt and check the oil lev-
el. It should be up to the brim of the hole. If
the level is low, add sufficient oil to raise it to
the specified level.CAUTION:
Be sure no foreign material enters the differen-
tial gear case. 3. Install the oil filler bolt and tighten it to the
specified torque.
Tightening torque:
Oil filler bolt:
23 Nm (2.3 m·kgf)
U5GH62.book Page 47 Monday, August 6, 2001 9:09 AM

8-49 1. Differential gear oil drain bolt
1. Boulon de vidange de l’huile de différentiel
1. Perno de drenaje de aceite de engranajes del diferencial
Differential gear oil replacement
1. Place the machine on a level place.
2. Place a container under the differential gear
case to catch the oil.
3. Remove the filler bolt and drain bolt to drain
the oil.
4. Install the drain bolt and tighten it to the spec-
ified torque.
Tightening torque:
Drain bolt:
10 Nm (1.0 m·kgf)
U5GH62.book Page 49 Monday, August 6, 2001 9:09 AM

8-93
3. Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reac-
tion and lead to poor brake performance.
4. Be careful that water does not enter the mas-
ter cylinder reservoir when refilling. Water will
significantly lower the boiling point of the fluid
and may result in vapor lock.
5. Brake fluid may deteriorate painted surfaces
or plastic parts. Always clean up spilled fluid
immediately.
6. Have a Yamaha dealer check the cause if the
brake fluid level goes down.
U5GH62.book Page 93 Monday, August 6, 2001 9:09 AM

10-1
EBU00428
SPECIFICATIONS
Model YFM4FAP
Dimensions:
Overall length 1,965 mm
Overall width 1,070 mm
Overall height 1,120 mm
Seat height 820 mm
Wheelbase 1,225 mm
Minimum ground clearance 245 mm
Minimum turning radius 3,000 mm
Basic weight:
With oil and full fuel tank 262 kg
Noise and vibration level:
Noise level (77/311/EEC) 79.5 dB(A)
Vibration on seat (EN1032, ISO5008) Not exceed 0.5 m/s
2
Vibration on handlebar (EN1032, ISO5008) 2.5 m/s
2
Engine:
Engine type Liquid-cooled 4-stroke, SOHC
Cylinder arrangement Forward-inclined single cylinder
Displacement 401 cm
3
Bore
× stroke 84.5
× 71.5 mm
Compression ratio 10.5 :1
Starting system Electric and recoil starter
Lubrication system Wet sump
U5GH62.book Page 1 Monday, August 6, 2001 9:09 AM