2002 YAMAHA BREEZE clock

4-25
EBU00092
Fuel tank cap
Remove the fuel tank cap by turning it counter-
clockwise.
EBU00093
Fuel cock
The fuel cock supplies fuel from the fuel tank to
the carburetor.
The fuel cock has three positions.
OFF: With the lever in this position fuel will not
flow. Always turn the lever to this position
when the engine is not running.
ON: With the lever in this position, fuel flows
to the carburetor. Normal riding is done
with the lever in this position.
RES: This indicates reserve. If you run out of
fuel while riding, turn the lever to this
position. THEN FILL THE FUEL TANK
AT THE FIRST OPPORTUNITY. After
refuelling, return the fuel cock lever to the
“ON” position.
q
RES
OFF
ON
1. Fuel tank cap1. Bouchon de réservoir de carburant1. Tapón del depósito de combustible
5KJ-62 (4~5 shou) 4/23/01 3:04 PM Page 26

8-63
EBU00351
Drive chain slack adjustment
1. Loosen the rear wheel hub bolts.
2. Loosen the adjuster locknuts on each side.
To tighten the chain, turn the chain adjuster
clockwise. To loosen the chain, turn the
adjuster counterclockwise and push the
wheel forward. Turn each adjuster exactly
the same amount to maintain correct axle
alignment.
There are marks on each side of the
swingarm and on each chain adjuster. Use
them to check for proper alignment.
3. After adjusting, be sure to tighten the lock-
nuts and the wheel hub bolts.
q
w
e
q
wqw
1. Upper bolt (×2) 2. Lower bolt (×2)1. Boulon supérieur (×2) 2. Boulon inférieur (×2)1. Tornillo superior (×2) 2. Tornillo inferior (×2)
1. Locknut (×2) 2. Adjuster (×2)
3. Alignment marks
1. Contre-écrou (×2) 2. Dispositif de réglage (×2)
3. Repères d’alignement
1. Contratuerca (×2) 2. Tornillo de ajuste (×2)
3. Marcas de alineación
Upper wheel hub bolt:
50 Nm (5.0 m0kg)
Lower wheel hub bolt:
50 Nm (5.0 m0kg)
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 64

8-77
2. Remove the bulb holder cover, turn the bulb
holder counterclockwise and remove the
defective bulb.
w
The headlight bulb is hot when it is on and
immediately after it is turned off. Wait for the
bulb to cool before touching or removing it.
You can be burned, or a fire could start if the
bulb touches something flammable.
3. Put a new bulb into position and secure it in
place with the bulb holder.
4. Install the bulb holder cover.
cC
Make sure the bulb holder cover is securely
fitted over the bulb holder and seated
against the reflector.
5. Install the headlight unit assembly.
Adjust the headlight beam if necessary.
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 78

8-81
EBU00861
Tail/brake light bulb replacement
1. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.
2. Remove the defective bulb from the bulb
holder by pushing it inward and turning it
counterclockwise.
3. Install a new bulb in the bulb holder by
pushing it inward and turning it clockwise.
4. Install the bulb holder (together with the
bulb).
q
q
w
1. Bulb holder1. Fixation d’ampoule1. Portabombillas
1. Bulb holder 2. Bulb
1. Fixation d’ampoule 2. Ampoule
1. Portabombillas 2. Bombilla
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 82