2002 YAMAHA BANSHEE 350 oil level

5-1
EBU00113
PRE-OPERATION CHECKS
Before using this machine, check the following points:
ITEM ROUTINE PAGE
Brakes9Check operation, free play, fluid level and fluid leakage. 5-5 ~ 5-9
9Fill with DOT 4 brake fluid if necessary. 8-73 ~ 8-83
Clutch9Check operation, condition and lever free play. 8-91
Parking brake9Check operation, condition and free play. 8-85 ~ 8-87
Fuel 9Check fuel level.
9Fill with fuel if necessary.5-11 ~ 5-13
Transmission oil9Check oil level.
9Fill with oil if necessary.5-17, 8-17 ~ 8-23
Coolant reservoir 9Check coolant level.
9Fill with coolant if necessary.8-23 ~ 8-37
Drive chain9Check chain slack and condition.
9Adjust if necessary.5-19, 8-91 ~ 8-97
Throttle9Check for proper throttle cable operation. 5-19, 8-71
Wheels and tires9Check tire pressure, wear and damage. 5-23 ~ 5-29, 8-105
Fittings and Fasteners9Check all fittings and fasteners. 5-19
Lights9Check for proper operation. 5-21, 8-107 ~ 8-111
5FK-9-63-4~5 2/7/02 1:25 PM Page 36

5-17
EBU00490Transmission oilMake sure the transmission oil is at the specified
level. Add oil as necessary. (See pages 8-17 ~
8-23.)cCBe sure to use motor oils that do not contain
anti-friction modifiers. Passenger car motor
oils (often labeled “Energy Conserving”) con-
tain anti-friction additives which will cause
clutch and/or starter clutch slippage, result-
ing in reduced component life and poor
engine performance.
Recommended oil:
SAE 10W30
Recommended oil classification:
API Service SE, SF, SG type or higher
Oil quantity:
Total amount:
1.7 L
Periodic oil change:
1.5 L
5FK-9-63-4~5 2/7/02 1:25 PM Page 52

8-9
NOTE:8Recommended brake fluid: DOT 4
8Brake fluid replacement:
1. When disassembling the master cylinder or caliper cylinder, replace the brake fluid. Normally
check the brake fluid level and add the fluid as required.
2. On the inner parts of the master cylinder and caliper cylinder, replace the oil seals every two
years.
3. Replace the brake hoses every four years, or if cracked or damaged.
5FK-9-63-8 2/7/02 1:28 PM Page 10

8-17
EBU00768Transmission oil
Transmission oil measurement
1. Place the machine on a level place.
2. Warm up the engine for several minutes
and then stop it.
3. Remove the dipstick and wipe it off with a
clean rag. Insert the dipstick in the filler
hole without screwing it in.NOTE:
Wait a few minutes until the oil level settles
before checking.4. Remove the dipstick and inspect the oil
level.
5. The oil level should be between the maxi-
mum and minimum marks. If the level is
low, add oil to raise it to the proper level.
6. Install the dipstick.
q
w
e
1. Dipstick
2. Maximum level mark 3. Minimum level mark1. Jauge
2. Repère de niveau maximum 3. Repère de niveau minimum1. Varilla de nivel
2. Marca de máximo 3. Marca de mínimo
5FK-9-63-8 2/7/02 1:28 PM Page 18

8-19
Transmission oil replacement
1. Place the machine on a level place.
2. Warm up the engine for several minutes
and then stop it.
3. Place a container under the engine.
4. Remove the dipstick and drain bolt to drain
the oil.
5. Install the drain bolt and then tighten it to
the specified torque.
6. Fill the engine with oil and install the dip-
stick.
q
1. Drain bolt1. Boulon de vidange1. Perno de vaciado
Tightening torque:
Drain bolt:
20 Nm (2.0 m0kg)
5FK-9-63-8 2/7/02 1:28 PM Page 20

q
w
1. Maximum level mark
2. Minimum level mark1. Repère maximum
2. Repère minimum1. Marca de máximo
2. Marca de mínimo
8-23
7. Start the engine and warm up for a few
minutes. While warming up, check for oil
leakage. If oil leakage is found, stop the
engine immediately, and check for the
cause.
8. Check the oil level.EBU00764*Cooling system
1. Check the coolant level in the coolant
reservoir when the engine is cold as the
coolant level will vary with engine temper-
ature. The coolant level should be
between the maximum and minimum
marks.
5FK-9-63-8 2/7/02 1:28 PM Page 24

8-77
3. Refill with the same type of brake fluid.
Mixing fluids may result in a harmful chem-
ical reaction and lead to poor brake perfor-
mance.
4. Be careful that water does not enter the
master cylinder when refilling. Water will
significantly lower the boiling point of the
fluid and may result in vapor lock.
5. Brake fluid may deteriorate painted sur-
faces or plastic parts. Always clean up
spilled fluid immediately.
6. Have a Yamaha dealer check the cause if
the brake fluid level goes down.
5FK-9-63-8 2/7/02 1:28 PM Page 78