2002 TOYOTA TUNDRA light

’02 TUNDRA_U (L/O 0108)
1062002 MY TUNDRA_U (OM 34417U)
Use the “2WD/4HI” and “4LO” buttons
to select the following transfer modes.
1. “2WD” (high speed position, two wheel drive): “2WD/4HI” and “4LO”
buttons left out
Use this for normal driving on dry,
hardsurfaced roads. This position
gives greater economy, the quietest
ride and least wear.
2. “4HI” (high speed position, four wheel drive): “2WD/4HI” button pushed
in
The “4HI” (high speed fourwheel
drive) indicator light comes on when
the “4HI” mode is selected.
Use this for normal driving on wet, icy
or snowcovered roads. This position
provides greater traction than two
wheel drive.
3. “4LO” (low speed position, four wheel drive): With the “2WD/4HI”
button pressed in, push the “4LO”
button
The “4LO” (low speed fourwheel drive)
indicator light comes on when the
“4LO” mode is selected.
Use this for maximum power and trac-
tion. Use “4LO” mode for climbing or
descending steep h ills, offroad driving,
and hard pulling in s and, mud or deep
snow. See “(c) Shifting procedure (button type)”
for further instructions.
The A.D.D. can be engaged or disen-
gaged by the shifting operations de-
scribed in “(c) Shifting procedure”.
You should drive in fourwheel drive for
at least 16 km (10 miles) each month.
This will assure that the front drive com-
ponents are lubricated.
(b) A.D.D.
(automatic disconnecting
differential)

’02 TUNDRA_U (L/O 0108)
1072002 MY TUNDRA_U (OM 34417U)
SHIFTING BETWEEN “H2” AND “H4”
To shift from “H2” to “H4”, reduce the
vehicle speed to less than 80 km/h (50
mph) and move the front drive control
lever. If the indicator light does not come
on when you shift the transfer into “H4”,
drive straight ahead while accelerating or
decelerating, or drive forward or backward
in a short distance. You need not depress
the clutch pedal.
If you have trouble shifting in cold weath-
er, reduce the vehicle speed or stop the
vehicle and reshift.
CAUTION
Never move the front drive control
lever if wheels are slipping. Stop the
slipping or spinning before shifting.
To shift from “H4” to “H2”, simply move
the front drive control lever.
This can be done at any speed. You need
not depress the clutch pedal.
If the indicator light does not go off when
you shift the transfer into “H2”, drive
straight ahead while accelerating or decel-
erating, or drive forward or backward in a
short distance. SHIFTING BETWEEN “H4” AND “L4”
To shift from “H4” to “L4”,
stop the
vehicle or reduce the vehicle speed to
less than 8 km/h (5 mph). With your foot
off the accelerator pedal, depress the
clutch pedal and move the front drive con-
trol lever.
To shift from “L4” to “H4”, depress the
clutch pedal and move the front drive con-
trol lever.
This can be done at any speed. SHIFTING BETWEEN “H2” AND “H4”
To shift from “H2” to “H4”,
reduce the
vehicle speed to less than 80 km/h (50
mph) and move the front drive control
lever.
If you have trouble shifting in cold weath-
er, reduce the vehicle speed or stop the
vehicle and reshift.
CAUTION
Never move the front drive control
lever if wheels are slipping. Stop the
slipping or spinning before shifting.
To shift from “H4” to “H2”, simply move
the front drive control lever.
This can be done at any speed.
If the indicator light does not go off when
you shift the transfer into “H2”, drive
straight ahead while accelerating or decel-
erating, or drive forward or backward in a
short distance.
SHIFTING BETWEEN “H4” AND “L4”
To shift between “H4” and “L4”, stop
the vehicle and put the transmission in
“N”. With the brake pedal depressed,
move the front drive control lever.
(c) Shifting procedure
(lever type with manual
transmission) (c) Shifting procedure
(lever type with automatic
transmission)

’02 TUNDRA_U (L/O 0108)
1082002 MY TUNDRA_U (OM 34417U)
SHIFTING BETWEEN “2WD” AND “4HI”
To shift from “2WD” to “4HI”, reduce
the vehicle speed to less than 100 km/h
(62 mph) and push in the “2WD/4HI” but-
ton.
If the “4HI” (high speed fourwheel drive)
indicator light flashes when you push in
the “2WD/4HI” button, this reminds you
that the transfer mode is not securely in
“4HI” mode. Drive straight ahead while
accelerating or decelerating.
If the “4HI” (high speed fourwheel drive)
indicator light flashes and the buzzer
sounds when you push in the “2WD/4HI”
button, this reminds you that the transfer
mode is not in “4HI” mode. Stop the ve-
hicle or reduce the vehicle speed to less
than 100 km/h (62 mph). Push the button
to turn it off, then once again to turn it
back on.
CAUTION
Never push the “2WD/4HI” button if
the wheels are slipping. Stop the slip-
ping or spinning before shifting.
To shift from “4HI” to “2WD”, push the
“2WD/4HI” button again to turn it off.
This can be done at any speed.
If the “4HI” (high speed fourwheel drive)
indicator light flashes when you push the
“2WD/4HI” button again to return to “2WD”
mode, this reminds you that the transfer
mode is not securely in “2WD” mode.
Drive straight ahead while accelerating or
decelerating, or drive forward or backward
in a short distance. SHIFTING BETWEEN “4HI” AND “4LO”
To shift from “4HI” to “4LO”,
stop the
vehicle and put the transmission into “N”.
With the brake pedal depressed, push the
“4LO” button. If the “2WD/4HI” button left
out, push in the “2WD/4HI” button to se-
lect the “4HI” mode.
If the “4LO” (low speed fourwheel drive)
indicator light flashes and the buzzer
sounds for 3 seconds when you push the
“4LO” button, this reminds you that the
transfer mode is not in “4LO” mode. Drive
forward or backward in a short distance,
then stop the vehicle completely, put the
transmission securely into “N” and push
the button again.
To shift from “4LO” to “4HI”, stop the
vehicle and put the transmission into “N”.
With the brake pedal depressed, push the
“4LO” button.
If the “4LO” (low speed fourwheel drive)
indicator light flashes and the buzzer
sounds for 3 seconds when you push the
“4LO” button, this reminds you that the
transfer mode is not in “4HI” mode. Drive
forward or backward in a short distance,
then stop the vehicle completely, put the
transmission securely into “N” and push
the button again.
(c) Shifting procedure
(button type)

’02 TUNDRA_U (L/O 0108)
1092002 MY TUNDRA_U (OM 34417U)
SHIFTING BETWEEN “2WD” AND “4LO”
To shift from “2WD” to “4LO”, stop the
vehicle and put the transmission into “N”.
With the brake pedal depressed, push the
“2WD/4HI” button in to select the “4HI”
mode, then push the “4LO” button.
If the “4LO” (low speed fourwheel drive)
indicator light flashes and the buzzer
sounds for 3 seconds when you push the
“4LO” button, this reminds you that the
transfer mode is not in “4LO” mode. Drive
forward or backward in a short distance,
then stop the vehicle completely, put the
transmission securely into “N” and push
the button again.
To shift from “4LO” to “2WD”, stop the
vehicle and put the transmission into “N”.
With the brake pedal depressed, push the
“2WD/4HI” switch again to turn it off. If the “4LO” (low speed fourwheel drive)
indicator light flashes and the buzzer
sounds when you push the “2WD/4HI” but-
ton, this reminds you that the transfer
mode is not in “2WD” mode. Push the
“2WD/4HI” button in to return to “4LO”
mode, drive forward or backward in a
short distance, then stop the vehicle com-
pletely, put the transmission securely into
“N” and push the “2WD/4HI” button once
again.
If the “4LO” (low speed fourwheel drive)
indicator light flashes when you push the
“2WD/4HI” button, this reminds you that
the transfer mode is not in “2WD” mode.
Drive straight ahead while accelerating or
decelerating, or drive forward or backward
in a short distance.
Pedal type
Lever type
Parking brake

’02 TUNDRA_U (L/O 0108)
11 02002 MY TUNDRA_U (OM 34417U)
When parking, firmly apply the parking
brake to avoid inadvertent creeping.
Pedal type—
To set: Fully depress the parking brake
pedal. For better holding power, first de-
press the brake pedal and hold it while
setting the parking brake.
To release: Depress the parking brake
pedal once again.
Lever type—
To set: Pull out on the lever. For better
holding power, first depress the brake
pedal and hold it while setting the parking
brake.
To release: Press the lock release button
(1), turn the lever (2), then push it in (3).
To remind you that the parking brake is
set, the parking brake reminder light in
the instrument panel remains on until you
release the parking brake.
CAUTION
Before driving, be sure the parking
brake is fully released and the park-
ing brake reminder light is off.
The cruise control allows you to cruise
the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off
the accelerator pedal.
Your cruising speed can be maintained up
or down grades within the limits of engine
performance, although a slight speed
change may occur when driving up or
down the grades. On steeper h ills, a
greater speed change will occur so it is
better to drive without the cruise control.
CAUTION
To help maintain maximum control
of your vehicle, do not use the
cruise control when driving in
heavy or varying traffic, or on slip-
pery (rainy, icy or snowcovered) or
winding roads.
Avoid vehicle speed increases when
driving downhill. If the vehicle
speed is too fast in relation to the
cruise control set speed, cancel the
cruise control then downshift the
transmission to use engine braking
to slow down.
TURNING ON THE SYSTEM
To operate the cruise control, press the
“CRUISE ONOFF” button. This turns the
system on. The indicator light in the
instrument panel shows that you can now
set the vehicle at a desired cruising
speed. Another press will turn the system
completely off.
CAUTION
To avoid accidental cruise control en-
gagement, keep the “CRUISE ON
OFF” switch off when not using the
cruise control.
Cruise control

’02 TUNDRA_U (L/O 0108)
11 22002 MY TUNDRA_U (OM 34417U)
On vehicles with automatic transmission,
even if you turn off the overdrive switch
with the cruise control on, engine braking
will not be applied because the cruise
control is not cancelled. To decrease the
vehicle speed, reset to a slower speed
with the cruise control lever or depress
the brake pedal. If you use the brake
pedal, cruise control is cancelled.
RESUMING THE PRESET SPEED
If the preset speed is cancelled by pulling
the control lever or by depressing the
brake pedal or clutch pedal, pushing the
lever up in the “RES/ACC” direction will
restore the speed set prior to cancellation.
However, once the vehicle speed falls be-
low about 40 km/h (25 mph), the preset
speed will not be resumed. CRUISE CONTROL FAILURE WARNING
If the “CRUISE” indicator light in the
instrument cluster flashes when using the
cruise control, press the “CRUISE ON
OFF” button to turn the system off and
then press it again to turn it on.
If any of the following conditions then oc-
curs, there is some trouble in the cruise
control system.
The indicator light does not come on.
The indicator light flashes again.
The indicator light goes out after it
comes on.
If this is the case, contact your Toyota
dealer and have your vehicle inspected.
To crank the engine without depressing
the clutch pedal, push the switch with
the ignition on.
The switch stays on as long as the igni-
tion is on. And it will automatically turn off
when the ignition is off. An indicator light
will illuminate to indicate the system is
operating.
This switch cancels the clutch start sys-
tem, which is designed to keep the starter
motor from operating if the clutch pedal is
not depressed all the way down.
The switch allows the vehicle to be driven
out of difficult situations by cranking the
engine with the clutch engaged.
Clutch start cancel switch

’02 TUNDRA_U (L/O 0108)
1462002 MY TUNDRA_U (OM 34417U)
AM
Fading—AM broadcasts are reflected by
the upper atmosphere—especially at night.
These reflected signals can interfere with
those received directly from the radio sta-
tion, causing the radio station to sound
alternately strong and weak.
Station interference—When a reflected sig-
nal and a signal received directly from a
radio station are very nearly the same
frequency, they can interfere with each
other, making it difficult to hear the broad-
cast.
Static—AM is easily affected by external
sources of electrical noise, such as high
tension power lines, lightening, or electri-
cal motors. This results in static.
CARING FOR YOUR CASSETTE PLAYER
AND TAPES
For the best performance for your cas-
sette player and tapes:
Clean the tape head and other parts regu-
larly.
A dirty tape head or tape path can
decrease sound quality and tangle your
cassette tapes. The easiest way to
clean them is by using a cleaning tape.
(A wet type is recommended.) Use highquality cassettes.
Lowquality cassette tapes can cause
many problems, including poor sound,
inconsistent playing speed, and
constant autoreversing. They can also
get stuck or tangled in the cassette
player.
Do not use a cassette if it has been
damaged or tangled or if its label is
peeling off.
Do not leave a cassette in the player
if you are not listening to it, especially
if it is hot outside.
Store cassettes in their cases and out
of direct sunlight.
Avoid using cassettes with a total play-
ing time longer than 100 minutes (50
minutes per side). The tape used in
these cassettes is thin and could get
stuck or tangled in the cassette player.
CARING FOR YOUR COMPACT DISC
PLAYER AND DISCS
Use only compact discs labeled as
shown above. CDR (CDRecordable),
CDRW (CDRewritable) and personal
computer use CDROMs may not be
playable on your compact disc player.
Your compact disc player is intended
for use with 12 cm (4.7 in.) discs only.
Extremely high temperatures can keep
your compact disc player from working.
On hot days, use the air conditioning
to cool the vehicle interior before you
listen to a disc.
Bumpy roads or other vibrations may
make your compact disc player skip.

’02 TUNDRA_U (L/O 0108)
1472002 MY TUNDRA_U (OM 34417U)
If moisture gets into your compact disc
player, you may not hear any sound
even though your compact disc player
appears to be working. Remove the
disc from the player and wait until it
dries.Your automatic changer or compact
disc player cannot play special shaped
or lowquality compact discs such as
those shown here. Do not use them as
the changer or player could be dam-
aged.
Handle compact discs carefully, espe-
cially when you are inserting them.
Hold them on the edge and do not
bend them. Avoid getting fingerprints
on them, particularly on the shiny side.
Dirt, scrapes, warping, pin holes, or
other disc damage could cause the
player to skip or to repeat a section of
a track. (To see a pin hole, hold the
disc up to the light.)
Remove discs from the compact disc
player when you are not listening to
them. Store them in their plastic cases
away from moisture, heat, and direct
sunlight.
To clean a compact disc: Wipe it with a
soft, lintfree cloth that has been damp-
ened with water. Wipe in a straight line
from the center to the edge of the disc
(not in circles). Dry it with another soft,
lintfree cloth. Do not use a conventional
record cleaner or antistatic device.