2002 TOYOTA LAND CRUISER instrument panel

36
When your vehicle is receiving signals from
the satellites, the ºGPSº mark appears at the
top left of the screen.
The GPS signal may be physically ob-
structed, leading to inaccurate vehicle posi-
tion on the map display. Tunnels, tall build-
ings, trucks, or even the placement of
objects on the instrument panel may obstruct
the GPS signals.
The installation of window tinting may also
obstruct the GPS signals. Most window tint-
ing contains some metallic content that will
interfere with the GPS signal reception. We
recommend not to use window tinting on ve-
hicles equipped with navigation systems. The GPS satellites may not send signals due
to repairs or improvements being made to
them.
Even when the navigation system is receiv-
ing good GPS signals, the vehicle position
may not be shown accurately or inappropri-
ate route guidance may occur in some
cases.

When driving on a small angled Y-
shaped road.
 When driving on a spiral road.
 When driving on a slippery road such as
in sand, gravel, snow, etc.
 When driving on a long straight road.
 When freeway and surface streets run in
parallel.
 After moving by ferry or vehicle carrier.
 When a long route is searched during high
speed driving.
 When driving without setting the current
position calibration correctly.
 After repeating a change of directions by
going forward and backward, or turning
on a turntable in the parking lot.
 When leaving a covered parking lot or
parking garage.
 When a roof carrier is installed.
 When driving with the tire chains installed.
(a) Accurate current vehicle
position may not be shown in
the following cases:

37
UNX401
Color and tone adjustment
You can adjust the color and the tone while
the DVD video and Video CD are being
played.
COLOR ºREDº:
Strengthens the red color of the screen.
COLOR ºGREENº:
Strengthens the green color of the screen.
TONE º+º: Strengthens the tone of the
screen.
TONE º-º: Weakens the tone of the screen.
UNG407
Depending on the position of the head-
light switch, the screen changes to the
day mode or night mode.
To display the screen in the day mode even
with the head light switch on, touch ºDAY
MODEº on the adjustment screen for bright-
ness and contrast control.
However, if the instrument panel light control
switch is turned fully to the right, mode
switching cannot be done. It remains in the
day mode. In this case, ºDAY MODEº is not
shown on the screen.
If the screen is set in the day mode with the
headlight switch turned to on, this condition
is memorized in the system even with the en-
gine turned off.

42
UNC502
2. Use the ºTEMPº button to set the de-
sired temperature.
The ºTEMPº button is used to set the de-
sired passenger compartment temperature.
The temperature of air delivered to the pas-
senger compartment will be controlled auto-
matically according to the setting. SETTING OPERATION - manual control
When one of the manual control buttons
is depressed while operating in automat-
ic mode, the mode relevant to the de-
pressed button is set. Other conditions
continue to be adjusted automatically.
If manual air flow selection is desired -UNX504UNX504
The outlets from which air is delivered can be
selected manually by touching the switch.
The function of each mode is as follows:
1
Panel - Air flows mainly from the instru-
ment panel vents.
2 Bi-level - Air flows from both the floor
vents and the instrument panel vents.
3 Floor - Air flows mainly from the floor
vents.
It is recommended that you close the lower
vent. For details about this, see page 46.
4 Floor/Windshield - Air flows mainly
from the floor vents and windshield
vents.
It is recommended that you close the lower
vent. For details about this, see page 46.
The selected mode is highlighted in green.
If quick heating or cooling is desired -
UNC502
Push the ºTEMPº button on either side and
hold it until the maximum figure or minimum
figure appears.