2002 TOYOTA LAND CRUISER air condition

5
Touch the
ºOFFº switch at the top of the
screen, and the information screen will no
longer be displayed.
INFORMATION

For scheduled maintenance infor- mation, please refer to the ºSched-uled Maintenance Guideº or ºOwn-er's Manual Supplementº.

Depending on your driving or theroad conditions, the system mayhave a time-lag between the datawhich have been inputted and theactual date and driving distance.
Information Items
Scheduled Maintenance
Oil Change
Replace Oil Filter
Rotate Tires
Replace Tires
Replace Battery
Replace Brake Pad
Replace Wiper Blades
Replace Engine Coolant
Replace Brake Fluid
Replace Automatic
Transmission Fluid
Replace Air Conditioning
Filter
Replace Air Cleaner Filter
Wedding Anniversary
Birthday

36The function returning to the previous
screen from the audio or air conditioner
screen is selectable.
1. Push
the
ºINFOº button on the bezel
to display the option screen and touch
the
ºScreen Transitionº switch.
UNG404
2. Select the ºONº or ºOFFº and then
touch the ºOKº.
ON: The previous screen automatically re-
turns f rom the audio or air conditioner screen
20 seconds after the end of audio or air con-
ditioner screen operation.
OFF: The audio or air conditioner screen re-
mains on. You can adjust the brightness or contrast
of the screen depending on the bright-
ness of your surroundings. You also can
turn the display off.
Push the
ºDISPLAYº button to display
the DISPLAY screen.UNG405
Contrast and brightness adjustment
CONTRAST º+º:
Strengthens the contrast of the screen.
CONTRAST º-º:
Weakens the contrast of the screen.
BRIGHTNESS º+º: Brightens the screen.
BRIGHTNESS º-º: Darkens the screen.
The screen turns off when you push the
ºSCREEN OFFº. To turn the display screen
back on, push any bezel switch such as
ºINFOº, etc. The selected screen appears.
Screen Transition Screen Adjustment

SECTION V
38
AIR CONDITIONING
Automatic air conditioning controls39
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39
Automatic Air Conditioning Controls
Page
1. Air conditioning operationscreen display button 41 . . . . . . . . . . .
2. Driver side temperature control button 42 . . . . . . . . . . . . . . . . . .
3. Front windshield button 44 . . . . . . . . .
4. Automatic control button 41 . . . . . . . .
5. OFF button 41 . . . . . . . . . . . . . . . . . . . . .
6. Air intake control button 43 . . . . . . . . .
7. Air conditioning on-off switch 44 . . .
8. Air flow control switch 42 . . . . . . . . . .
9. Fan speed control switch 43 . . . . . . . .

41


The automatic air conditioning auto-
matically maintains the set tempera-
ture.
This air conditioning features automatic
fan speed and air flow control which auto-
matically selects the most suitable fan
speed and air flow to control the tempera-
ture. The ignition key must be in the ºONº
position.
CLIMATE: Push this button to display
switches for automatic air conditioning con-
trols.
NOTICE
To prevent the battery from being dis- charged, do not leave the air condition-
ing on longer than necessary when the
engine is not running.
SETTING OPERATION - automatic con-
trol
UNC501
1. Push the ºAUTOº button.
Air flow quantity, switching of the diffusers,
on-of f of the air conditioning, and switching
of the air intake between RECIRCULATED
AIR and OUTSIDE AIR are automatically ad-
justed. The operation status is shown by
each indicator.
When one of the manual control buttons is
depressed while operating in automatic
mode, the mode relevant to the depressed
button is set. Other conditions continue to be
adjusted automatically. Push
the ºOFFº button to turn the air condi-
tioning off.
It is recommended that you close the lower
vent. For details about this, see page 46.
(a) Climate control

42
UNC502
2. Use the ºTEMPº button to set the de-
sired temperature.
The ºTEMPº button is used to set the de-
sired passenger compartment temperature.
The temperature of air delivered to the pas-
senger compartment will be controlled auto-
matically according to the setting. SETTING OPERATION - manual control
When one of the manual control buttons
is depressed while operating in automat-
ic mode, the mode relevant to the de-
pressed button is set. Other conditions
continue to be adjusted automatically.
If manual air flow selection is desired -UNX504UNX504
The outlets from which air is delivered can be
selected manually by touching the switch.
The function of each mode is as follows:
1
Panel - Air flows mainly from the instru-
ment panel vents.
2 Bi-level - Air flows from both the floor
vents and the instrument panel vents.
3 Floor - Air flows mainly from the floor
vents.
It is recommended that you close the lower
vent. For details about this, see page 46.
4 Floor/Windshield - Air flows mainly
from the floor vents and windshield
vents.
It is recommended that you close the lower
vent. For details about this, see page 46.
The selected mode is highlighted in green.
If quick heating or cooling is desired -
UNC502
Push the ºTEMPº button on either side and
hold it until the maximum figure or minimum
figure appears.

44In the following cases, the RECIRCULATED
mode may change to the OUTSIDE AIR
mode automatically to prevent interior fog.

When the outside temperature becomes
lower than 4 C (39F).
 When the air conditioning compressor
malfunctions.
 When the air conditioning cooler refriger-
ant decreases. If manual on-off of the air conditioning is
desired -
Push the ºA/Cº
button to turn the air condi-
tioning on and push it again to turn the air
conditioning off.
If the outside temperature is lowered down to
around 0 C (32F), the air conditioning will
turn off automatically.
If the system is used for ventilation, heating
in dry weather or removing frost or exterior
fog on the windshield, turn the air condition-
ing off once it is no longer required. This will
improve fuel economy. The air conditioning
can be used for year-round automatic tem-
perature control including cooling and dehu-
midifying operation.
If the air conditioning compressor does not
operate, the indicator of the ºA/Cº button will
blink. If the indicator of the ºA/Cº button
blinks even when the ºA/Cº button is pushed
again, have the compressor checked by
your nearest Toyota dealer.
UNC504
To remove interior fog on the windshield-
Push the ºFRONT WINDSHIELDº button.
To remove frost or exterior fog on the
windshield-
1. Push the upper side of the temperature control button until maximum figure ap-
pears on the temperature display.
2. Push the ºFRONT WINDSHIELDº but- ton.
(b) Windshield defogging and
defrosting

45
3. Push
the ºHIº of the air flow control switch
to obtain a maximum air flow.
4. Leave the air conditioning on-off button off.
For further information for removing frost and
fog, see ºLower ventº on page 46.
When the ºFRONT WINDSHIELDº button is
pushed while operating in automatic mode,
the air conditioning is set to operate and the
OUTSIDE AIR mode is set.
Push the ºA/Cº button for dehumidified heat-
ing or cooling. This setting clears the front
view more quickly.
If you push the ºFRONT WINDSHIELDº but-
ton once again while in the FRONT WIND-
SHIELD mode, the mode then returns to the
last mode used.
CAUTION
Do not use the ºFRONT WINDSHIELDº
button during cooled air operation in
extremely humid weather. The differ-
ence between the temperature of the
outside air and that of the windshield
could cause the outer surface of the
windshield to fog up blocking your vi-
sion.
(c) Rear air conditioning switch
UNC505
To turn on the rear air conditioning when
you sit on the front seat, push this switch.
The rear air conditioning operates in the
automatic mode. To adjust the air flow
and setting temperature, follow the steps
in accordance with ºRear air conditioning
controlsº in the Owner's Manual.