2002 SUZUKI GRAND VITARA electrical

YH4
GRAND
VITARA
8-4 BODY ELECTRICAL SYSTEM

When performing a work that produces a heat exceeding 80C
in the vicinity of the electrical parts, remove the heat sensitive
electrical part(s) beforehand.

Use care not to expose connectors and electrical parts to water
which will be a cause of a trouble.

When using a tester for checking continuity or measuring voltage,
be sure to insert the tester probe from the wire harness side.
SYMBOLS AND MARKS
Refer to Section 8A.
ABBREVIATIONS
Refer to Section 8A.

YH4
GRAND
VITARA
Symbol
G : Green
G / Y : Green / Yellow G (Base Color)
G (Base Color)
Y (Stripe Color)G/Y
BODY ELECTRICAL SYSTEM 8-5
WIRE COLOR SYMBOLS
The wire color is abbreviated to the first (or first two) alphabet(s) of
each color.
There are two kinds of colored wire used in this vehicle. One is
single-colored wire and the other is dual-colored (striped) wire.
The single-colored wire uses only one color symbol (i.e. ªGº).
The dual-colored wire uses two color symbols (i.e. ªG / Yº). The first
symbol represents the base color of the wire (ªGº in the figure) and
the second symbol represents the color of the stripe (ªYº in the fig-
ure).
JOINT CONNECTOR (J / C)

Wiring of this vehicle employs joint connector (J / C) which divide
one wire into several different wires or combine several different
wires into one wire.

The joint connector is as shown in the figure.
FUSE BOX AND RELAY
Refer to Section 8A.

YH4
GRAND
VITARA
8-6 BODY ELECTRICAL SYSTEM
POWER SUPPLY DIAGRAM
Refer to Section 8A.

YH4
GRAND
VITARA
8G-8 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
[NOTES ON SYSTEM CIRCUIT INSPECTION]
Refer to ªPrecautions for Electrical Circuit Serviceº and ªIntermit-
tents and Poor Connectionº in Section 0A.
[Precaution after replacing ECM / PCM or Immobilizer Control Mod-
ule]

When ECM / PCM was replaced, including when replaced be-
cause rechecking by using a known-good ECM / PCM was neces-
sary during trouble diagnosis, the ECM/Immobilizer Control Mod-
ule code must be registered in ECM / PCM and Immobilizer
Control Module by performing procedure described in ªProce-
dure after ECM / PCM Replacementº on p. 8G-27. If it is not regis-
tered, the engine would not start and accurate trouble diagnosis
would not be assured.

When Immobilizer Control Module was replaced, including when
replaced because rechecking by using a known-good Immobiliz-
er Control Module was necessary during trouble diagnosis, the
Transponder code and ECM/Immobilizer Control Module code
must be registered in Immobilizer Control Module and ECM/Im-
mobilizer Control Module code in ECM / PCM by performing pro-
cedure described in ªProcedure after Immobilizer Control Module
Replacementº on p. 8G-26. If they are not registered, the engine
would not start and accurate trouble diagnosis would not be as-
sured.

YH4
GRAND
VITARA
BODY SERVICE 9-63
KEY CODING
KEY USAGE AND IDENTIFICATION
Key is used for ignition and door lock cylinder. Keys are cut on both
edges to make them reversible.
Key identification is obtained from five character key code stamped
on key code tag. Using this key code, key code cutting combination
can be determined from a code list (available to owners of key cut-
ting equipment from suppliers).
If key codes are not available from records or tags, key code can
be obtained from the right hand door lock cylinder (if lock has not
been replaced). Lock cylinders supplied by the factory as service
parts are unmarked.
If original key is available, key code cutting combination can be de-
termined by laying key.
IGNITION SWITCH LOCK CYLINDER
Removal / Installation
See Section 3C1, ªAIR BAG STEERING WHEEL AND COLUMNº.
ELECTRICAL DIAGNOSIS
For ignition switch electrical troubleshooting, see Section 8, ªBODY
ELECTRICAL SYSTEMº.

YH4
GRAND
VITARA
(A)(A)
(A)
10B-6 AIR BAG SYSTEM
DIAGNOSIS
WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equipment
other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.
DIAGNOSTIC TROUBLE CODES
The ªAir Bag Diagnostic System Checkº must always be the starting point of any air bag system diagnosis. The
ªAir Bag Diagnostic System Checkº checks for proper ªAIR BAGº warning lamp operation and checks for air bag
diagnostic trouble codes using the Tech-1 (scan tool) or on-board diagnosis function.

Current diagnostic trouble code ± Malfunction that are presently being detected.

History diagnostic trouble code ± All malfunction detected since the last time the history memory was cleared.
USE OF SPECIAL TOOLS
WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equipment
other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.
You should be familiar with the tools listed under ªSpecial Toolsº in this section. You should be able to measure
voltage and resistance. You should be familiar with proper use of a scan tool such as the Tech-1 Diagnostic Com-
puter, Driver/Passenger Load Tool, Connector Test Adapter Kit and the Digital Multimeter.
Special Tool (Connector Test Adapter Kit)
(A): 09932-76010
This must be used whenever a diagnostic procedure requests
checking or probing a terminal.
Using the appropriate adapter in the special tool will ensure that no
damage to the terminal will occur from the multimeter probe, such
as spreading or bending.
The adapter will also give an idea of whether contact tension is suffi-
cient, helping to find an open or intermittent open due to poor termi-
nal contact.

YH4
GRAND
VITARA
(A)
10B-8 AIR BAG SYSTEM
INTERMITTENT AND POOR CONNECTIONS
Most intermittent are caused by faulty electrical connections or wir-
ing. When a check for proper connection is requested in a diagnos-
tic flow table, perform careful check of suspect circuits for:

Poor mating of connector halves, or terminals not fully seated in
the connector body (backed out).

Dirt or corrosion on the terminals. The terminals must be clean
and free of any foreign material which could impede proper termi-
nal contact.
However, cleaning the terminal with a sand paper or the like is
prohibited.

Damaged connector body, exposing the terminals to moisture
and dirt, as well as not maintaining proper terminal orientation
with the component or mating connector.

Improperly formed or damaged terminals.
If any abnormality is found, repair or replace as a wire harness as-
sembly.
Check each connector terminal in problem circuits carefully to en-
sure good contact tension by using the corresponding mating termi-
nal included in the connector test adapter kit (special tool).
If contact tension is not enough, reform it to increase contact ten-
sion or replace.
Special Tool (Connector Test Adapter Kit)
(A): 09932-76010

Poor terminal-to-wire connection.
Check each wire harness in problem circuits for poor connection
by shaking it by hand lightly.
If any abnormal condition is found, change the wire harness as-
sembly or component parts with new ones.

YH4
GRAND
VITARA
10B-10 AIR BAG SYSTEM
AIR BAG DIAGNOSTIC SYSTEM CHECK
WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equipment
other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.
CAUTION:
The order in which diagnostic trouble codes are diagnosed is very important. Failure to diagnose the
diagnostic trouble codes in the order specified may result in extended diagnostic time, incorrect diag-
nosis and incorrect parts replacement.
The diagnostic procedures used in this section are designed to find and repair air bag system malfunctions.
To get the best results, it is important to use the diagnostic flow tables and follow the sequence listed below.
A. PERFORM THE ªAIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLEº
The ªAir Bag Diagnostic System Check Flow Tableº must be the starting point of any air bag system diagnostics.
The ªAir Bag Diagnostic System Check Flow Tableº checks for proper ªAIR BAGº warning lamp operation, the
ability of the SDM to communicate through ªAIR BAGº warning lamp and whether air bag diagnostic trouble
codes exist.
B. REFER TO THE PROPER DIAGNOSTIC TABLE AS DIRECTED BY THE ªAIR BAG DIAGNOSTIC SYSTEM
CHECK FLOW TABLEº.
The ªAir Bag Diagnostic System Check Flow Tableº will lead you to the correct chart to diagnose any air bag
system malfunctions. Bypassing these procedures may result in extended diagnostic time, incorrect diagnosis
and incorrect parts replacement.
C. REPEAT THE ªAIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLEº AFTER ANY REPAIR OR DIAGNOS-
TIC PROCEDURES HAVE BEEN PERFORMED.
Performing the ªAir Bag Diagnostic System Check Flow Tableº after all repair or diagnostic procedures will en-
sure that the repair has been made correctly and that no other malfunctions exist.