2002 SUZUKI GRAND VITARA transmission range
[x] Cancel search: transmission rangePage 432 of 801
YH4
GRAND
VITARA
7B1-30 AUTOMATIC TRANSMISSION (4 A / T)
Running condition Gear shift Abnormal
noise
ConditionPossible CauseCorrection
Poor 1st speed run-
ning or excessive
slippage in ªDº or ª2ºFluid pressure leakage from forward clutch
due to wear or breakage of O/D case seal
ringReplace.
Overdrive clutch slippingReplace.
Unable to run or ex-
cessive slippage in
ªLº rangeFluid pressure leakage of forward clutch
due to wear or breakage of O/D case seal
ringReplace.
Reverse brake disc slippingReplace.
Broken brake piston O-ringReplace.
Unable to run or ex-
cessive slippage in
ªRº rangeFluid pressure leakage to direct clutch due
to wear or breakage of center support seal
ringReplace.
Worn direct clutchReplace.
Poor 1±2 shift, ex-
cessive slippageFluid pressure leakage to overdrive clutch
due to wear or breakage of O/D case seal
ringReplace.
Faulty second brakeReplace.
Broken O-ring of second brake pistonReplace.
Faulty second coast brake (in ª2º range)Replace.
Poor 2±3 shift, ex-
cessive slippageFluid pressure leakage to overdrive clutch
due to wear or breakage of O/D case seal
ringReplace.
Worn direct clutch bushingReplace.
Direct clutch slippingReplace.
Foreign material caught in direct clutch pis-
ton check ballReplace.
Poor start or surging
in ªDº rangeFluid pressure leakage of forward clutch
due to wear or breakage of O/D case seal
ringReplace.
Malfunction of forward clutchReplace.
Poor 3±4 shift, ex-
ili
Faulty overdrive brakeReplace.
cessive slippageFaulty overdrive clutchReplace.
Poor start or judder-
ing in ªRº rangeFluid pressure leakage of direct clutch due
to wear or breakage of oil center support
seal ringReplace.
Worn direct clutchReplace.
Excessive shock on
1± 2 shiftFaulty one-way clutchReplace.
Non operate lock-up
systemFaulty torque converterReplace.
Abnormal noise in
ªPº or ªNº rangeWorn oil pumpReplace.
SCAN TOOL DATA-Refer to SECTION 6 / 6-1.
INSPECTION OF PCM AND ITS CIRCUIT-Refer to SECTION 6 / 6-1.
WIRE HARNESS AND CONNECTORS-Refer to SECTION 6 / 6-1.
Page 433 of 801
YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-31
Brake pedal Released Depressed
Voltage 0 VBattery
voltage
DIAGNOSTIC FLOW TABLE A-1 (NO TCC LOCK-UP OCCURS)
SYSTEM DESCRIPTION
PCM turns TCC solenoid OFF under any of the following conditions.
Brake pedal switch: ON
4WD LOW switch: ON
Cruise control module: TCC OFF command signal is output (if equipped).
ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor, its
circuit or engine cooling
system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-8 (G16 / J20 engines) or C51-1-2 (H25
engine) terminal of PCM coupler and ground.
Normal mode in ªDº range.
Transfer ª2Hº position.
Cruise control is not operated (if equipped).
Brake pedal released.
Drive vehicle with TCC ON condition
referring to ªTCC lock-up diagramº in
this section.
Is it battery voltage?Faulty TCC solenoid
valve, its circuit or
transmission.Go to Step 4.
4Is vehicle equipped with H25 engine?Go to Step 5.Go to Step 6.
5Brake switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-31 terminal of PCM coupler
terminal and ground.
Is the result as specified?Go to Step 6.Faulty brake pedal switch
or its circuit.
If OK, substitute a known-
good PCM and recheck.
Page 435 of 801
YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-33
O / D cut
switchOFF ON
VoltageBattery
voltage0 V
DIAGNOSTIC FLOW TABLE A-2 (NO GEAR SHIFT TO O / D)
SYSTEM DESCRIPTION
PCM does not shift to O / D gear under any of the following conditions.
O / D cut switch: ON
4WD LOW switch: ON
Cruise control module: O / D OFF command signal is output (if equipped).
ECT: ECT < 30C (86F)
TROUBLESHOOTING
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 person, a driver and tester, on a level road.
STEPACTIONYESNO
1Was ªAUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLEº performed?Go to Step 2.Go to ªAUTOMATIC
TRANSMISSION
DIAGNOSTIC FLOW
TABLEº.
2ECT check:
(1) Warm up engine to normal operating
temperature.
(2) Check ECT using scan tool.
Is ECT more than 30C (86F)?Go to Step 3.Faulty ECT sensor,
its circuit or engine
cooling system.
If OK, substitute a known-
good PCM and recheck.
3Perform running test under the following
conditions and check voltage between
C51-1-2 (G16 / J20 engines) or C51-1-6 (H25
engine) terminal of PCM coupler and ground,
C51-1-1 terminal of PCM coupler and ground.
O / D cut switch OFF (ªO / D OFFº lamp OFF).
Normal mode in ªDº range.
Transfer ª2Hº position.
Cruise control is not operated (if equipped).
Drive vehicle with 4th gear condition
referring to ªGear shift diagramº in this
section.
Is each voltage about 0 V?Faulty shift solenoid
valve, its circuit or
transmission.ªGº wire or ªG / Rº wire
shorted to power circuit.
If OK, go to Step 4.
4O / D cut switch signal inspection:
(1) With ignition switch ON, check voltage
between E61-33 (G16 / J20 engines) or
E61-14 (H25 engine) terminal of PCM
coupler and ground.
Is the result as specified?Go to Step 5.Faulty O / D cut switch or
its circuit.
If OK, substitute a known-
good PCM and recheck.
Page 441 of 801
YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-39
G16 / J20 Engines
H25 Engine
1. PCM
2. J / B
3. Transmission range
sensor (switch)
1. PCM
2. Fuse
3. J / C
4. Transmission range
sensor (switch)
DTC P0705 (DTC NO.72) TRANSMISSION RANGE SENSOR (SWITCH) CIRCUIT
MALFUNCTION
WIRING DIAGRAM
Page 442 of 801
YH4
GRAND
VITARA
7B1-40 AUTOMATIC TRANSMISSION (4 A / T)
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
Transmission range switch signal (P, R, N, D, 2 or L)
is not inputted for 25 sec. at 60 km/h (38 mph) or
higher vehicle speed.
or
Multiple signals are inputted simultaneously for 25
sec.
(2 driving cycles detection logic)Transmission range sensor (switch) maladjusted.
Transmission range sensor (switch) or its circuit mal-
function.
PCM
DTC CONFIRMATION PROCEDURE
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC and start engine.
3) Shift A / T selector lever to each of L, 2, D, N, R and P ranges for 30 seconds each.
4) Increase vehicle speed to about 70 km / h (45 mph) in D range.
5) Keep driving above vehicle speed for 30 seconds.
6) Release accelerator pedal, decrease vehicle speed and stop vehicle.
7) Check DTC and / or pending DTC.
Page 443 of 801
YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-41
C51-1
-18C51-1
-17C51-1
-16C51-1
-15C51-1
-28C51-1
-27 G16/
J20
H25
C51-1-4 C51-1-3 C51-1-13 C51-1-12 C51-1-20 C51-1-19
Terminal
Select
lever
position
TROUBLESHOOTING (DTC P0705)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Check Transmission Range Switch (Sensor) Circuit for
Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition
switch OFF.
2) Turn ignition switch ON and check transmission
range signal (P, R, N, D, 2 or L) on display
when shifting select lever to each range.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C51-1-15, C51-1-16,
C51-1-17, C51-1-18, C51-1-27 and C51-1-28 for
G16/J20 (C51-1-4, C51-1-3, C51-1-13, C51-1-12,
C51-1-20 and C51-1-19 for H25) respectively with
select lever shifted to each range.
Taking terminal C51-1-28 for G16/J20 (C51-1-20 for
H25) as an example, is battery voltage indicated
only when select lever is shifted to ª2º range and
0 V for other ranges as shown in figure?
Check voltage at other terminals likewise, referring
to figure.
Are check results satisfactory?Intermittent trouble.
Check for intermittent
referring to ªIntermit-
tent and Poor
Connectionº in
section 0A.Go to Step 3.
3Check Select Cable for Adjustment referring to ªSelect
Cable Adjustmentº in this section.
Is it adjusted correctly?Go to Step 4.Adjust.
4Check Transmission Range Switch for Installation
Position.
1) Shift select lever to ªNº range.
2) Check that ªNº reference line on switch and center
line on shaft are aligned.
Are they aligned?Go to Step 5.Adjust.
5Check Transmission Range Switch (Sensor) referring
to ªTransmission Range Switchº in this section.
Are check results satisfactory?ªYº, ªOr / Gº, ªRº,
ªOr / Blº, ªY / Gº,
ªG / Orº or ªG / Blº
circuit open or short.
If wires and
connections are OK,
substitute a known-
good PCM and
recheck.Replace TR switch.
Fig. for Step 2.
Page 444 of 801
YH4
GRAND
VITARA
G16/J20 Engines H25 Engine
G16/J20 Engines
H25 Engine
1. PCM
2. A / T input speed sensor 11 1 0
Bl / Y Bl / G16 8
Bl / Y Bl / G
7B1-42 AUTOMATIC TRANSMISSION (4 A / T)
DTC P0715 (DTC NO.76) INPUT / TURBINE SPEED SENSOR CIRCUIT MALFUNCTION
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC DETECTING CONDITIONTROUBLE AREA
Input speed sensor detected speed is lower than spec-
ification while vehicle running under all of the following
conditions:
at higher than 10 km / h (7 mph) with 1st gear in D
range for 1 sec. or more.
at higher than 20 km / h (13 mph) with 2nd gear in D
range for 2 sec. or more.
at higher than 30 km / h (20 mph) with 3rd gear in D
range for 2 sec. or more.
(2 driving cycles detection logic)Input speed sensor and its circuit
PCM
DTC CONFIRMATION PROCEDURE
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC.
3) Start engine and turn O / D cut switch ON.
4) Shift select lever to D range and start vehicle.
5) Keep vehicle speed at higher than 10 km / h (7 mph) with 1st gear in D range for 2 sec. or more.
6) Increase vehicle speed and keep it at higher than 20 km / h (13 mph) with 2nd gear in D range for 2 sec. or more.
7) Increase vehicle speed and keep it at higher than 30 km / h (20 mph) with 3rd gear in D range for 2 sec. or more.
8) Stop vehicle.
9) Check DTC and / or pending DTC.
Page 445 of 801
YH4
GRAND
VITARA
Oscilloscope waveforms
2V/Div.
Waveforms at specified idle
speed in ªPº range5ms / Div.
AUTOMATIC TRANSMISSION (4 A / T) 7B1-43
TROUBLESHOOTING (DTC P0715)
STEPACTIONYESNO
1Was ªA / T DIAG. FLOW TABLEº performed?Go to Step 2.Go to ªA / T DIAG.
FLOW TABLEº.
2Input speed sensor circuit check:
1) Remove PCM cover.
2) With ignition switch OFF, disconnect PCM
connectors.
3) Check for proper connection to input speed sensor
at C51-1-10 and C51-1-11 terminals for G16/J20
(at C51-1-8 and C51-1-16 terminals for H25)
4) If OK, check resistance of sensor circuit.
Resistance between C51-1-10
and C51-1-11 for G16 / J20
(C51-1-8 and C51-1-16 for H25):530 ± 650 at
20C, 68F
Resistance between C51-1-10 /
C51-1-11 for G16 / J20 (C51-1-8 /
C51-1-16 for H25) and ground: 1 M or more
Are check results satisfactory?Go to Step 4.Go to Step 3.
3Input speed sensor check:
1) With ignition switch OFF, disconnect input speed
sensor connector.
2) Check for proper connection to input speed sensor
at each terminals.
3) If OK, then check resistance of input speed sensor.
Are measured values as specified in Step 2?ªBl / Gº or ªBl / Yº wire
open or shorted to
ground.Replace input speed
sensor.
4Check visually input speed sensor and overdrive clutch
drum for the followings.
No damage
No foreign material attached
Correct installation
Are they in good condition?Intermittent trouble
or faulty PCM.
Check for intermittent
referring to
ªIntermittent and
Poor Connectionº in
Section 0A.Clean, repair or
replace.
Reference
Connect oscilloscope between C51-1-11 (+) and C51-1-10 (±) for
G16 / J20 (C51-1-16 (+) and C51-1-8 (±) for H25) of PCM connector
connected to PCM and check input speed sensor signal.