2002 SUZUKI GRAND VITARA Assembly

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-3
1
A1 A2 A3 A4
A5 A6 A9 A10A7 A8
1. Coil antenna
2. Immobilizer Control Module
3. ECM/PCM
4. Immobilizer diagnostic coupler
4-1. Diagnostic output terminal
4-2. Ground terminal
5. Malfunction indicator lamp
6. Main relay
7. Ignition switch
8. Fuse
9. Main fuse
-10. To #9-pin in Data link connector
-11. To #7-pin in Data link connector
-12. To ABS control module
-13. Immobilizer indicator lamp
(Vehicle not equipped with monitor coupler)
-14. Monitor coupler (Vehicle not equipped
with immobilizer indicator lamp)) Terminal arrangement of Immobilizer
Control Module coupler (Viewed from
harness side)
B/R
BI
BI/B
B/W
V/Y
BI/B
B/W
B
V/W
V/W
BI
R
SbI
B
V/G
V
B
R/Y WIRE
SYMBOLWIRE
COLORabcdefghijklmn
1. Ignition key with built-in
transponder
1
1. Coil antenna
opqr
IGNITION KEY
The ignition key for the immobilizer control system has a built-in
transponder. Each transponder in the key has an each transmitting
code (Transponder code). The code will transmitted from the key
via the coil antenna to Immobilizer Control Module when the ignition
switch is turned ON.
COIL ANTENNA
The coil antenna is installed to the steering lock assembly. As it is
energized by Immobilizer Control Module, it transmits the trans-
ponder code of the ignition key to Immobilizer Control Module.

YH4
GRAND
VITARA
9
BODY SERVICE 9-1
GLASS, WINDOWS AND MIRRORS9- 2 . . . . .
Front Door Glass 9- 2. . . . . . . . . . . . . . . . . . . . .
Front Door Window Regulator 9- 5. . . . . . . . . .
Windshield 9- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Door Glass 9-12. . . . . . . . . . . . . . . . . . . . .
Rear Door Window Regulator 9-14. . . . . . . . . .
Quarter Window 9-15. . . . . . . . . . . . . . . . . . . . . .
Back Door Glass 9-16. . . . . . . . . . . . . . . . . . . . .
BODY STRUCTURE9-17 . . . . . . . . . . . . . . . . . . .
Front Door Assembly 9-17. . . . . . . . . . . . . . . . .
Rear Door Assembly 9-18. . . . . . . . . . . . . . . . . .
Back Door / Rear Gate Assembly 9-19. . . . . . . .
Hood 9-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Fender 9-22. . . . . . . . . . . . . . . . . . . . . . . . .
Front Bumper 9-23. . . . . . . . . . . . . . . . . . . . . . . .
Rear Bumper 9-24. . . . . . . . . . . . . . . . . . . . . . . .
Under Body Dimensions 9-25. . . . . . . . . . . . . . .
Body Dimensions 9-26. . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER
INFORMATION9-33 . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 9-33. . . . . . . . . . . . . . . . . . . . .
SEAT9-34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seat 9-34. . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Seat 9-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
PAINT AND COATINGS9-36 . . . . . . . . . . . . . . . .
Anti-Corrosion Treatment 9-36. . . . . . . . . . . . . .
Metal Replacement Parts Finishing 9-37. . . . .
Plastic Parts Finishing 9-58. . . . . . . . . . . . . . . . .
SECURITY AND LOCKS9-59 . . . . . . . . . . . . . . . .
Front Door Lock Assembly 9-59. . . . . . . . . . . . .
Rear Door Lock Assembly 9-61. . . . . . . . . . . . .
Back Door / Rear Gate Lock Assembly 9-62. . .
Key Coding 9-63. . . . . . . . . . . . . . . . . . . . . . . . . .
SUNROOF / CONVERTIBLE TOP9-64 . . . . . . . . .
Sliding Roof (if equipped) 9-64. . . . . . . . . . . . . .
Canvas Top And Topbow Frames 9-71. . . . . . .
EXTERIOR AND INTERIOR TRIM9-72 . . . . . . .
Floor Carpet 9-72. . . . . . . . . . . . . . . . . . . . . . . . .
Head lining 9-73. . . . . . . . . . . . . . . . . . . . . . . . . .
Roof Trim (2 Door Model) 9-75. . . . . . . . . . . . . .
Side Moldings (if equipped) 9-77. . . . . . . . . . . .
Splash Guard (if equipped) 9-78. . . . . . . . . . . .
Roof Rail (if equipped) 9-79. . . . . . . . . . . . . . . .
Roof Molding 9-79. . . . . . . . . . . . . . . . . . . . . . . .
Luggage Under Box 9-80. . . . . . . . . . . . . . . . . .
SECTION 9
BODY SERVICE
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).

When body servicing, if shock may be applied to air bag system component parts, remove those parts
beforehand. (Refer to Section 10B.)
NOTE:
Fasteners are important attaching parts in that they could affect the performance of vital components and
systems, and / or could result in major repair expense. They must be replaced with one of the same part
number of with an equivalent part if replacement becomes necessary.
Do not use a replacement part of lesser quality or substitute a design. Torque values must be used as spe-
cified during reassembly to assure proper retention of these parts.
CONTENTS

YH4
GRAND
VITARA
BODY SERVICE 9-17
1. Stopper pin
1. Rags
2. Wooden piece
1. Upper hinge
mounting bolts
2. Lower hinge
mounting bolt
3. Door
4. Body
1. Front door hinge
2. Upper hinge nut (rear door)
3. Rear door hinge
BODY STRUCTURE
FRONT DOOR ASSEMBLY
REMOVAL
1) Remove front fender. Refer to ªFRONT FENDERº in this section.
2) Disconnect door harness lead wires at each coupler.
3) Remove stopper pin.
4) Support door panel using a jack with a piece of wood placed be-
tween jack and panel, as shown.
5) Remove door assembly by loosening hinge mounting bolts.
INSTALLATION
Reverse removal procedure to install door assembly, noting follow-
ing point.
NOTE:
When replacing door, coat replacement door inside with wax
for proper anticorrosion treatment.
Refer to ªUNDERCOATING / ANTI-CORROSION COMPOUND
APPLICATION AREAº in this section.

Tighten door hinge bolts (and nut) to specified torque.
Tightening torque
(a): 27 N
.m (2.7 kg-m, 19.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

Adjust door latch striker position by referring to ªFRONT DOOR
LOCK INSTALLATIONº section so that door is positioned correctly.

Adjust front door cushion so that door contacts body when closed.

After installation, open and close the door to check looseness.
Replace door open stopper pin when there is looseness.

When weatherstrip is hardened, water leak may develop.
In such case, replace it with new one.

YH4
GRAND
VITARA
9-18 BODY SERVICE
REAR DOOR ASSEMBLY
REMOVAL / INSTALLATION
Follow procedures for Front Door removal / installation in this sec-
tion.

YH4
GRAND
VITARA
BODY SERVICE 9-19
1. Back door panel assy
2. Back door window glass
3. Back door hinge
4. Back door / Rear gate balancer unit
1. Back door hinge
2. Back door
3. Body
BACK DOOR / REAR GATE ASSEMBLY
REMOVAL
1) Remove back door trim, and door / rear gate sealing cover, refer
to steps 1) to 4) of BACK DOOR LOCK ASSEMBLY in this sec-
tion.
2) Remove wire harness connector inside the back door / rear gate.
3) Remove back door / rear gate balancer (first at its door-side and
next at its body-side), as shown.
WARNING:
Handling of Back Door / Rear Gate Balancer (Damper)

Do not disassemble balancer because its cylinder is
filled with gas.

The gas itself is harmless but it may issue out of the
hole together with chips generated by the drill.
Therefore, be sure to wear goggle.

When discarding removed back door / rear gate balanc-
er (damper), use a 2 to 3 mm (0.08 to 0.12 in.) drill to
make a hole as shown.

Handle balancer carefully. Do not scar or scratch ex-
posed surface of its piston rod, and never allow any
paint or oil to stick to its surface.

Do not turn piston rod with balancer fully extended.
5) Remove back door / rear gate hinge bolts and back door / rear
gate.

YH4
GRAND
VITARA
9-20 BODY SERVICE
1. Sealing cover
2. Adhesive
INSTALLATION
Reverse removal procedure to install back door / rear gate noting
following points.

Secure wiring harness.

Secure back door / rear gate sealing cover.
NOTE:
Use adhesive to seal sealing cover to back door / rear gate.

Adjust back door / rear gate latch striker position by referring
ªBACK DOOR LOCK ASSEMBLY INSTALLATIONº so that back
door / rear gate is positioned correctly.

Adjust back door / rear gate cushion so that back door / rear gate
contacts body when closed.

YH4
GRAND
VITARA
BODY SERVICE 9-23
1. Front bumper
2. Screws
3. Front bumper member
4. Side marker
FRONT BUMPER
NOTE:

Fasteners are important attaching parts in that they could affect the performance of vital components
and systems, and / or could result in major repair expense. They must be replaced with one of the same
part number or with an equivalent part if replacement becomes necessary.
Do not use a replacement part of lesser quality or substitute design. Torque values must be used as spe-
cified during reassembly to assure proper retention of these parts.

Before removing front bumper, remove fender lining and disconnect connector of side marker.

YH4
GRAND
VITARA
1. (a)
1. (a)
1
11
Tightening Torque
(a): 23 N.m (2.3 kg-m, 17.0 lb-ft)
1. Bolt
BODY SERVICE 9-33
INSTRUMENTATION AND DRIVER INFORMATION
INSTRUMENT PANEL
WARNING:
See WARNING at the beginning of this section.
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to ªDisabling Air Bag Systemº in
Section 10B.
3) Remove console box.
4) Remove glove box and column hole cover.
5) Disconnect wires and cables from heater unit and blower motor
assembly.
6) Remove steering column assembly. Refer to Section 3C1.
7) Disconnect speedometer connector and remove speedometer
assembly. If equipped with air bag, disconnect wire coupler at
SDM and air bag ground terminal for air bag.
8) Remove engine hood opener.
9) Disconnect couplers which need to be disconnected for removal
for instrument panel.
10) Remove instrument panel mounting screws.
11) Remove instrument panel mounting bolt.
12) Remove instrument panel.
CAUTION:
For vehicle with Air Bag, instrument panel could not be re-
moved with SDM coupler connected and ground terminal
installed.
Use care not to damage Air Bag harness.
INSTALLATION
1) Install instrument panel by reversing removal procedure, noting
the following items.

When installing each part, be careful not to catch any cable or
wiring harness.

When installing steering column assembly, refer to ªAIR BAG
STEERING COLUMN INSTALLATIONº in Section 3C1.
2) Adjust control cables. (Refer to Section 1A ªHEATER CON-
TROL CABLESº.)
3) Enable air bag system. Refer to ªEnabling Air Bag Systemº in
Section 10B.