2002 SUZUKI GRAND VITARA bleeding

YH4
GRAND
VITARA
5-8 BRAKES
4) When fluid pressure in the cylinder is almost depleted, retigh-
ten bleeder plug.
5) Repeat this operation until there are no more air bubbles in hy-
draulic line.
6) When bubbles stop, depress and hold brake pedal and tighten
bleeder plug.
For tightening torque specification of air bleeder plug, re-
fer to ªTIGHTENING TORQUE SPECIFICATIONº in this
section.
7) Then attach bleeder plug cap.
8) After completing bleeding operation, apply fluid pressure to
pipe line and check for leakage.
9) Replenish fluid into reservoir up to specified level.
10) Check brake pedal for ªsponginessº. If found spongy, repeat
entire procedure of bleeding.

YH4
GRAND
VITARA
1. Stop light switch
BRAKES 5-9
BRAKE PEDAL FREE HEIGHT CHECK
Remove foot rest and displace carpet and dash silencer(s) so as to
measure brake pedal free height between pedal face and asphalt
sheet installed on dash panel.
Brake pedal free height ªaº from asphalt sheet:
208 ± 218 mm (8.19 ± 8.58 in.)
If the measurement is not within the specification, check the posi-
tion of booster push rod clevis and / or stop light switch according
to the instruction shown in this section.
The free height varies depending on installation position of booster
push rod clevis and stop light switch.
BRAKE LIGHT SWITCH ADJUSTMENT
Adjustment should be made as follows when installing switch. Pull
up brake pedal toward you and while holding it there, adjust switch
position so that clearance between end of thread and brake pedal
return cushion (shown as ªbº in figure).
Then tighten lock nut to specified torque.
Clearance ªbº: 1.5 ± 2.0 mm (0.06 ± 0.08 in.)
Tightening Torque
(b): 7.5 N
.m (0.75 kg-m, 5.5 lb-ft)
EXCESSIVE PEDAL TRAVEL CHECK
1) Remove foot rest and displace carpet and dash silencer(s).
2) Start engine.
3) Depress brake pedal a few times.
4) With brake pedal depressed with approximately 30 kg (66 lbs)
load, measure pedal to asphalt sheet clearance ªcº.
Clearance ªcº: over 115 mm (4.53 in.)
5) If clearance ªcº is less than specification, the most possible
cause is either rear brake shoes are worn out beyond limit or air
is in lines.
Should clearance ªcº remain less than specification even after
replacement of brake shoes and bleeding of system, other pos-
sible but infrequent cause is malfunction of rear brake shoe ad-
justers or booster push rod length out of adjustment.

YH4
GRAND
VITARA
5A-18 BRAKES PIPE / HOSE / MASTER CYLINDER
1. LSPV spring bolt
2. LSPV bolt
3. Brake pipe flare nut
4. Air bleeding plug
1. LSPV lever
2. Stopper bolt (if equipped)
3. Coil spring ªAº: Don't turn(a)
2) Torque each bolt and nut to specification as indicated respec-
tively in figure.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
(b): 16 N
.m (1.6 kg-m, 11.5 lb-ft) (brake flare nut)
(c): 7.5 N
.m (0.75 kg-m, 9.0 lb-ft) (bleeder plug)
3) Upon completion of installation, fill reservoir tank with specified
fluid and bleed air from brake system.
NOTE:
Make sure to bleed air from LSPV bleeder without failure.
4) After bleeding air, check that LSPV is installed properly, referring
to following INSPECTION & ADJUSTMENT.
INSPECTION & ADJUSTMENT
Confirm the following before inspection and adjustment.

Fuel tank is filled with fuel fully.

Vehicle is equipped with spare tire, tools, jack and jack handle.

Vehicle is free from any other load.
With vehicle in above conditions;
1) Place it on level floor.
2) Push up (for 5 door model) or push down (for 3 door model)
LSPV lever with finger till it stops and measure length ªLº of coil
spring as it is pulled.
3) Spring length ªLº should be the value specified below.
Spring length (between spring end and spring bolt)
ªLº: 103 mm (4.06 in.) (5 door model). . . . .
ªLº: 157 mm (6.18 in.) (3 door model). . . . .
4) If it isn't, adjust it to specification by changing stay positions as
shown in figure. After adjustment, tighten bolt to specified
torque.
For details, refer to left figure.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
NOTE:
Check to make sure that LSPV body and brake pipe joints
are free from fluid leakage. Replace defective parts, if any.

YH4
GRAND
VITARA
2
1. Wheel cylinder
2. Gasket
1. Brake back plate
2. Brake pipe flare nut
3. Brake pipe
4. Wheel cylinder bolts
PARKING AND REAR BRAKE 5C-13
4) Install bleeder plug cap taken off from pipe back to bleeder plug.
5) For procedure hereafter, refer to steps 1) to 5) of BRAKE SHOE
INSTALLATION.
NOTE:
Be sure to bleed brake system. (for bleeding operation, re-
fer to BLEEDING BRAKES in Section 5.)
INSTALLATION (For gasket sealed type)
1) Install gasket to joint seam of wheel cylinder and brake back
plate. Then take off bleeder plug cap from brake pipe and con-
nect pipe (or pipes) to wheel cylinder just enough to prevent fluid
from leaking.
NOTE:
Be sure to check gasket for deterioration or any damage be-
fore installation and replace if found defective.
2) Tighten wheel cylinder to brake back plate to specified torque.
3) Torque flare nut (or nuts) of brake pipe which was connected in
step 1) to specification.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
(b): 16 N
.m (1.6 kg-m, 12.0 lb-ft)
4) Install bleeder plug cap taken off from pipe back to bleeder plug.
5) For procedure hereafter, refer to BRAKE SHOE INSTALLA-
TION.
NOTE:
Be sure to bleed brake system. Refer to ªCHECK AND AD-
JUSTMENTº in BRAKES section.

YH4
GRAND
VITARA
5C-16 PARKING AND REAR BRAKE
1. Brake back plate
2. Cable cap
3. Parking brake cable
6) Install wheel cylinder, and tighten wheel cylinder bolts and
brake pipe flare nut (or nuts) to specified torque. (Refer to steps
1) to 4) of WHEEL CYLINDER INSTALLATION of this section.)
7) Install parking brake cable to brake back plate.
8) Install brake shoes, referring to steps 1) to 4) of BRAKE SHOE
INSTALLATION.
9) Install brake drum. Refer to steps 1) to 2) of BRAKE DRUM
INSTALLATION in this section.
10) Refill differential housing with new specified gear oil. Refer to
ªMAINTENANCE SERVICEº in Section 7E for refill.
11) Fill reservoir with brake fluid and bleed brake system. (For
bleeding operation, refer to BLEEDING BRAKES in Section 5.)
12) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque
(b): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
13) Upon completion of all jobs, depress brake pedal with about 30
kg (66 lbs) load three to ten times so as to obtain proper drum-
to-shoe clearance.
Adjust parking brake cable. (For adjustment, refer to PARKING
BRAKE CHECK AND ADJUSTMENT in Section 5.)
14) Tighten rear center console box screws.
15) Check to ensure that brake drum is free from dragging and
proper braking is obtained. Then remove vehicle from hoist
and perform brake test (foot brake and parking brake).
16) Check each installed part for oil leakage.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-33
1. ABS hydraulic unit /
control module
assembly
2. Nut
1. To left-front
2. To right-front
3. To rear
4. From master cylinder4) Remove three nuts and take out ABS hydraulic unit / control
module assembly from bracket.
CAUTION:

Do not give an impact to hydraulic unit.

Use care not to allow dust to enter hydraulic unit.

Do not place hydraulic unit on its side or upside down.
Handling it in inappropriate way will affect its original
performance.
INSTALLATION
1) Install hydraulic unit by reversing removal procedure.
Tightening Torque
(a): 16 N
.m (1.6 kg-m, 12.0 lb-ft)
(b): 21 N
.m (2.1 kg-m, 15.5 lb-ft)
(c): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
2) Bleed air from brake system. Refer to ªBLEEDING BRAKESº in
Section 5.
3) Check each installed part for fluid leakage and perform hydraulic
unit operation check.

YH4
GRAND
VITARA
1. Pipe
2. Hose
3. Flare nut
1. Pipe
2. Hose
3. Flare nut
4. E-ring
1. Master cylinder
assembly
2. Clutch pipe
3. Attaching nut
4. Attaching bolt
5. Clevis pin
6. Clip
7. Flare nut
CLUTCH 7C1-5
INSPECTION
Check pipe and hose for dent, kink, crack, dirt and dust. Replace
if check result is not satisfactory.
INSTALLATION
Reverse removal sequence noting following points.
Tighten flare nuts to specified torque.
Tightening Torque
(a): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
NOTE:

For air bleeding of master cylinder alone, it must be removed
from vehicle.
(For procedures of removal and installation of master cylin-
der assembly and air bleeding, refer to CLUTCH MASTER
CYLINDER section.)

Do not allow fluid to get on painted surface.

Do not allow pipe and hose to contact hard against vehicle
or other parts.

Install each clamp securely.

Install E-ring securely as shown.

After installation, check clutch pedal free travel and bleed air
from system.

Check fluid leakage.

Add fluid close to MAX level of reservoir.
CLUTCH MASTER CYLINDER
REMOVAL
1) Clean around reservoir cap and take out fluid with syringe or
such.
2) Remove push rod clevis pin.
3) Disconnect fluid pipe from master cylinder.
NOTE:
Do not allow fluid to get on painted surfaces.
4) Remove master cylinder attaching nut and bolt.
5) Remove master cylinder assembly and gasket.

YH4
GRAND
VITARA
1. Master cylinder
1. Attaching bolt
2. Attaching nut
3. Clevis pin
ªAº
7C1-6 CLUTCH
INSTALLATION
1) To bleed air from master cylinder itself, tilt it as shown in figure
and add fluid into it.
NOTE:
After bleeding air from master cylinder, plug pipe hole in it
to prevent fluid from spilling out of it till pipe is connected.
2) Install master cylinder assembly and new gasket to body, attach-
ing bolt, nuts and push rod clevis pin.
NOTE:
Do not reuse gasket.
3) Torque attaching bolt and nut to specification.
4) Connect fluid pipe and torque flare nut to specification.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
(b): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
5) Apply grease to clevis pin and install it.
ªAº: Grease 99000-25010
6) Fill reservoir with specified brake fluid and check fluid leakage.
7) After installation, bleed air from system and check clutch pedal
free travel. Refer to BRAKE section for air bleeding procedure.
FLUID INSPECTION
Fluid level should be always between MIN and MAX lines on reser-
voir. If fluid decreases quickly, check for leakage, repair leaky point,
if any, and add fluid up to MAX level.
NOTE:

Brake fluid damages painted surface badly. Should it get on
painted surface, remove it immediately and clean surface
thoroughly.

Do not use shock absorber fluid or any other fluid which con-
tains mineral oil. Do not use container which has been used
for mineral oil or which is wet from water. Mineral oil will
cause swelling and distortion of rubber parts in hydraulic
clutch system and water will mix with brake fluid, lowering
fluid boiling point. Keep all fluid containers capped to pre-
vent contamination.

Make sure not to use fluid whose container cap was first
opened more than a year ago.