2002 SUZUKI GRAND VITARA Tensioner

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-7
Special Tool (Air Bag Driver/Passenger Load Tool)
(B): 09932-75010
This tool is used only when called for in this section. It is used as
a diagnostic aid and safety device to prevent inadvertent air bag (in-
flator) module deployment and seat belt pretensioner activation.
The load tool has three connectors attached to its case are electri-
cally functional and serve as resistive load substitutions.
No more than two connectors are used at any time.
One of connectors (ªAº: BASE OF COLUMN) is used to substitute
the load of the driver air bag (inflator) module and the contact coil
assembly when it is connected at the base of the column to the air
bag wire harness.
Another connector (ªBº: STEERING WHEEL) is used to substitute
the load of followings.

Driver air bag (inflator) module when it is connected at the top of
the column to the contact coil assembly.

Passenger air bag (inflator) module when it is connected to the
air bag harness connector for passenger air bag (inflator) module.

Driver and passenger seat belt pretensioner when it is connected
to air bag harness connector for driver and passenger seat belt
pretensioner.
The third connector (ªCº: PASSENGER INFLATOR) is not used.
By substituting the resistance of the load tool when called for, a de-
termination can be made as to whether an inflator circuit compo-
nent is causing system malfunction and which component is caus-
ing the malfunction.
The load tool should be used only when specifically called for in the
diagnostic procedures.

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-15
DIAGNOSTIC TROUBLE CODE TABLE (Page 2 of 2)
DIAGNOSTIC TROUBLE CODEDIAGNOSISNO.MODEDIAGNOSIS
41Resistance high
42Driver
pretensionerResistance low
43circuit
(if equipped)Short to ground
44Short to power circuit
45Resistance highDiagnose trouble
di t ªDi
46Passenger
pretensionerResistance low
according to ªDiagnos-
tic Flow Tableº corre-
sponding to each code
47circuit
(if equipped)Short to ground
s onding to each code
No.
48Short to power circuit
51SDMFrontal crash detected
61ªAIR BAGº warning lamp circuit
71SDMInternal fault
NOTE:

When 2 or more codes are indicated, the lowest numbered code will appear first.

If a code not listed on the table is displayed, then the SDM is faulty.

Current DTC and history DTC can be identified by lighting and flashing of ªAIR BAGº warning lamp as
follows.
Current DTC is set.
(Abnormality exists at present.)History DTC is set only. (Faulty condi-
tion occurred once in the past but nor-
mal condition is restored at present.)
ªAIR BAGº warning lamp
after ignition switch ONRemains ON.Flashing 6 times and turns OFF.
ªAIR BAGº warning lamp
when grounding diagnosis
switch
Current DTC is displayed.History DTC is displayed.
However, if a multiple number of DTC's are set an even one of them is a current DTC, ªAIR BAGº warning
lamp remains on after ignition switch is turned ON. Therefore, it is not possible to identify any of them
as to whether it is a current one or a history one. (But use of scan tool (Tech 1) will make identification
possible.)

YH4
GRAND
VITARA
1. SDM
2. Passenger seat belt pretensioner
3. Driver seat belt pretensioner
: Shorting bar
: Air bag harness
10B-44 AIR BAG SYSTEM
CODE 41 ± DRIVER PRETENSIONER INITIATOR CIRCUIT RESISTANCE HIGH
CODE 45 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT RESISTANCE HIGH
(Page 1 of 2)
CAUTION:

When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).

When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.

When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
DTC WILL SET WHEN:
The resistance of driver or passenger seat belt pretensioner initiator circuit is above a specified value for specified
time.

YH4
GRAND
VITARA (A)
For DTC 45
ªA11º
ªA12º
(A)
For DTC 41
STEERING WHEEL 1. Pretensioner
harness
EXAMPLE: For driver side
AIR BAG SYSTEM 10B-45
CODE 41 ± DRIVER PRETENSIONER INITIATOR CIRCUIT RESISTANCE HIGH
CODE 45 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT RESISTANCE HIGH
(Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, remove front
pillar lower trim of applicable side then
disconnect seat belt pretensioner
connector.
2) Check proper connection to applicable
seat belt pretensioner at terminals in ªGº
or ªHº connector.
3) If OK then connect Special Tool (B) to
seat belt pretensioner connector
disconnected at the step 1).
4) With ignition switch ON, is DTC 41 or
45 still current?Go to step 2.1) Ignition switch OFF.
2) Replace seat belt preten-
sioner (Refer to
SECTION 10A).
21) With ignition switch OFF, disconnect
SDM.
2) Check proper connection to SDM at
terminals ªA13º and ªA14º or ªA11º
and ªA12º.
3) If OK then measure resistance between
ªA13º and ªA14º terminals or ªA11º and
ªA12º terminals with connected Special
Tool (B).
4) Is resistance 2.9
or less?Substitute a known-
good SDM and recheck.DTC41:
Repair high resistance or
open in ªPº or ªWº wire
circuit.
DTC45:
Repair high resistance or
open in ªLgº or ªBrº wire
circuit.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
1. SDM
2. Passenger seat belt pretensioner
3. Driver seat belt pretensioner
: Shorting bar
: Air bag harness
10B-46 AIR BAG SYSTEM
CODE 42 ± DRIVER PRETENSIONER INITIATOR CIRCUIT RESISTANCE LOW
CODE 46 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT RESISTANCE LOW
(Page 1 of 2)
CAUTION:

When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).

When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.

When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
DTC WILL SET WHEN:
The resistance of driver or passenger seat belt pretensioner initiator circuit is below a specified value for specified
time.

YH4
GRAND
VITARA (A)
For DTC 46
ªA11º
ªA12º
(A)
For DTC 42
2. Pretensioner
harnessSTEERING WHEEL
EXAMPLE: For driver side
AIR BAG SYSTEM 10B-47
CODE 42 ± DRIVER PRETENSIONER INITIATOR CIRCUIT RESISTANCE LOW
CODE 46 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT RESISTANCE LOW
(Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, remove front
pillar lower trim of applicable side then
disconnect seat belt pretensioner
connector.
2) Check proper connection to applicable
seat belt pretensioner at terminals in ªGº
or ªHº connector.
3) If OK then connect Special Tool (B) to
seat belt pretensioner connector
disconnected at the step 1).
4) With ignition switch ON, is DTC 42 or
46 still current?Go to step 2.1) Ignition switch OFF.
2) Replace seat belt preten-
sioner (Refer to
SECTION 10A).
21) With ignition switch OFF, disconnect
SDM.
2) Check proper connection to SDM at
terminals ªA13º and ªA14º or ªA11º
and ªA12º.
3) If OK then measure resistance between
ªA13º and ªA14º terminals or ªA11º and
ªA12º terminals with connected Special
Tool (B).
4) Is resistance 1.7
or more?Substitute a known-
good SDM and recheck.DTC42:
Repair short from ªPº wire
circuit to ªWº wire circuit or
from ªPº or ªWº wire circuit to
other wire circuit.
DTC46:
Repair short from ªLgº wire
circuit to ªBrº wire circuit or
from ªLgº or ªBrº wire circuit
to other wire circuit.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.

YH4
GRAND
VITARA
1. SDM
2. Passenger seat belt pretensioner
3. Driver seat belt pretensioner
: Shorting bar
: Air bag harness
10B-48 AIR BAG SYSTEM
CODE 43 ± DRIVER PRETENSIONER INITIATOR CIRCUIT SHORT TO GROUND
CODE 47 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT SHORT TO GROUND
(Page 1 of 2)
CAUTION:

When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).

When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.

When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
DTC WILL SET WHEN:
The voltage measured at driver or passenger seat belt pretensioner initiator circuit is below a specified value for
specified time.

YH4
GRAND
VITARA (A)
ªA11º
(A)
1. Pretensioner
harness
For DTC 43
For DTC 47
STEERING WHEEL
EXAMPLE: For driver side
AIR BAG SYSTEM 10B-49
CODE 43 ± DRIVER PRETENSIONER INITIATOR CIRCUIT SHORT TO GROUND
CODE 47 ± PASSENGER PRETENSIONER INITIATOR CIRCUIT SHORT TO GROUND
(Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic Check Flow Tableº.
STEP
ACTIONYESNO
11) With ignition switch OFF, remove front
pillar lower trim of applicable side then
disconnect seat belt pretensioner
connector.
2) Check proper connection to applicable
seat belt pretensioner at terminals in ªGº
or ªHº connector.
3) If OK then connect Special Tool (B) to
seat belt pretensioner connector
disconnected at the step 1).
4) With ignition switch ON, is DTC 43 or 47
still current?Go to step 2.1) Ignition switch OFF.
2) Replace seat belt preten-
sioner (Refer to
SECTION 10A).
21) With ignition switch OFF, disconnect
Special Tool (B) and SDM.
2) Measure resistance between ªA13º or
ªA11º and ªA10º terminals.
3) Is resistance 1 k
or more?Substitute a known-
good SDM and recheck.DTC43:
Repair short ªPº or ªWº wire
circuit to ground.
DTC47:
Repair short from ªLgº or ªBrº
wire circuit to ground.
Fig. for STEP 1 and 2 Fig. for STEP 2
Special Tool
(A): 09932-76010
(B): 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Clear diagnostic trouble codes (refer to ªDiagnostic Trouble Code (DTC) Clearanceº), if any.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.