2002 SUZUKI GRAND VITARA Power switch

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-9
IDLE UP SYSTEM
IDLE UP SYSTEM CHECK
1) Warm up engine to normal operating temperature.
2) Turn A / C switch OFF, if equipped.
3) Turn steering wheel fully and check idle speed.
Engine idle speed drops a little momentarily when steering
wheel is turned fully but returns to its specified level immediately.
If power steering pressure switch connector is connected, check
the same with that connector disconnected. Momentary drop of
engine idle speed should be less when it is connected than when
disconnected.
FLUID
FLUID LEAKAGE CHECK
Start engine and turn steering wheel fully to the right and left so that maximum hydraulic pressure is provided. Then
visually check gear box, P / S pump and P / S fluid reservoir themselves and each joint of their connecting pipes for
leakage.
CAUTION:
Never keep steering wheel turned fully for longer than 10 seconds.

YH4
GRAND
VITARA
3B1-20 POWER STEERING (P / S) SYSTEM
1. P/S fluid
reservoir
2. Suction hose
1. P / S pulley
2. Mounting bolt
9. Vane
10. Rotor
11. Snap ring
12. Side plate
13. Pulley (pump shaft)
14. Oil seal
15. Pump body
16. Flow control
valve Assembly 1. Suction connector
2. O-ring
3. Pressure switch
4. Flow control valve
(Relief valve)
5. Spring
6. Plug
7. Pump cover
8. Cam ring
REMOVAL
NOTE:
Be sure to clean each joint of suction and discharge sides
thoroughly before removal.
1) Remove suction hose from pump, then disconnect battery nega-
tive cable.
2) Remove P / S fluid reservoir with suction hose.
3) Remove union bolt. Then disconnect high pressure pipe from
pump.
NOTE:
As fluid flows out of disconnected joints, put a receptacle
under joints or a plug to pipe.
4) Disconnect pressure switch lead wire at switch terminal.
5) Loosen related bolts and remove power steering drive belt.
6) Remove P / S pump mounting bolt (s).
7) Remove P / S pump.
NOTE:
Plug each port of removed pump to prevent dust or any oth-
er foreign matter from entering.
DISASSEMBLY
1) Clean its exterior thoroughly.
2) With aluminum plates placed on vise first, grip pump body with
it.
3) Remove suction connector bolt, suction connector and O-ring
from pump body.
4) Remove power steering pressure switch (terminal set) from
pump body.
5) Remove plug, flow control spring and relief valve (flow control
valve) from pump body.
6) Remove cover bolts, pump cover and O-ring from pump body.
7) Remove snap ring from pump shaft.
8) Remove vanes from rotor.
9) Remove cam ring, rotor, side plate and O-rings from pump
body.
10) Pull out pulley from pump body.
11) Remove oil seal from pump body.

YH4
GRAND
VITARA
3B1-24 POWER STEERING (P / S) SYSTEM
1. Pump cover
1. Pressure switch
1. Suction connector
2. O-ring
1. Suction connector
15) Gradually tighten new pump cover bolts to specified torque.
NOTE:
After installing pump cover, check to make sure that shaft
can be turned by hand.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
16) Apply power steering fluid to O-ring of terminal switch.
17) Install pressure switch to pump body.
Tightening Torque
(a): 28 N
.m (2.8 kg-m, 20.0 lb-ft)
18) Apply power steering fluid to relief valve (flow control valve).
19) Install relief valve (flow control valve) to pump body.
20) Install flow control spring.
21) Apply power steering fluid to O-rings of plug.
22) Install O-rings to plug.
23) Tighten plug to specified torque.
Tightening Torque
(a): 60 N
.m (6.0 kg-m, 43.5 lb-ft)
24) Apply power steering fluid to O-ring of suction connector.
25) Install O-ring to suction connector.
26) Install suction connector to pump body as shown in figure.
Tighten new suction connector bolts to specified torque.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)

YH4
GRAND
VITARA
3B1-26 POWER STEERING (P / S) SYSTEM
09915-77420
Oil pressure gauge
attachment and hose set09915-77410
Oil pressure gauge09943-55010
Boot clamp plier
TIGHTENING TORQUE SPECIFICATION
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Gear box mounting bolts555.540.0
Gear box cylinder pipe flare nuts292.921.0
Gear box low pressure pipe union bolt404.029.0
Gear box high pressure pipe union bolt353.525.5
Tie-rod end lock nut656.547.0
G16 Type engine555.540.0
Pump bracket boltJ20 Type engine252.518.5
H25 Type engine454.532.5
Pump union bolt606.043.5
Oil pump mount bolts252.518.5
Pipe clamp bolt / Reservoir bracket bolt111.18.0
Steering shaft joint bolt252.518.0
High pressure flare nuts404.029.0
Pump cover bolts232.317.0
Plug606.043.5
Pressure switch (Terminal)282.820
Suction connector bolt101.07.5
Tie-rod end nut484.835.0
Tie-rod (for canvas top LH model only)858.561.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUPER GREASE (A)
(99000-25010)
Oil seal lip of P / S pump pulley shaft
Power steering fluidAn equivalent of DEXRON
-III or
DEXRON
-II

To fill P / S fluid reservoir

Parts lubrication when installing
SPECIAL TOOL

YH4
GRAND
VITARA
Diagnostic Trouble Code (DTC) Table 5E1-14. . .
System Circuit 5E1-15. . . . . . . . . . . . . . . . . . . . . . .
Table ± A ªABSº Warning Lamp Circuit
Check ± Lamp does not come ªONº
at ignition switch on 5E1-16. . . . . . . . . . . . . . . . . .
Table ± B ªABSº Warning Lamp Circuit
Check ± Lamp comes ªONº steady 5E1-17. . . .
Table ± C ªABSº Warning Lamp Circuit
Check ± The lamp flashes continuously
while ignition switch is on5E1-18 . . . . . . . . . . . . . .
Table ± D Code (DTC) is not Outputted
even with Diag. Switch Terminal
Connected to Ground 5E1-19. . . . . . . . . . . . . . . .
Table ± E EBD Warning Lamp (Brake
Warning Lamp) Check-lamp Comes
ªONº Steady 5E1-20. . . . . . . . . . . . . . . . . . . . . . . .
DTC 15 ± G Sensor Circuit 5E1-21. . . . . . . . . . . .
DTC 21, 22, 25, 26, 31, 32, 35 or 36
± Wheel Speed Sensor Circuit 5E1-23. . . . . . . .
DTC 41, 45 or 56 ± Solenoid Circuit 5E1-26. . . . .
DTC 57 ± Solenoid and Pump Motor
Power Source Circuit 5E1-27. . . . . . . . . . . . . . . .
DTC 61 ± ABS Pump Motor Circuit 5E1-28. . . . . .
DTC 63 ± ABS Fail-Safe Relay Circuit 5E1-29. . .
DTC 71 ± ABS Control Module 5E1-30. . . . . . . . .
ON-VEHICLE SERVICE5E1-31 . . . . . . . . . . . . . . . .
Precaution 5E1-31. . . . . . . . . . . . . . . . . . . . . . . . . . .
ABS Hydraulic Unit Operation Check 5E1-31. . . .
ABS Hydraulic Unit / Control Module
Assembly 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic unit inspection 5E1-32. . . . . . . . . . . . . Removal 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-33. . . . . . . . . . . . . . . . . . . . . . . . .
Front Wheel Speed Sensor 5E1-34. . . . . . . . . . . .
Output voltage inspection 5E1-34. . . . . . . . . . . .
Removal 5E1-35. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-35. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-35. . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Front Sensor Rotor 5E1-36. . . . . . . . . . . . . . . . . . .
Removal 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Wheel Speed Sensor 5E1-37. . . . . . . . . . . .
Output voltage inspection 5E1-37. . . . . . . . . . . .
Removal 5E1-37. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-38. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-38. . . . . . . . . . . . . .
Installation 5E1-38. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Sensor Rotor 5E1-39. . . . . . . . . . . . . . . . . . . .
Removal 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . .
G Sensor 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Transfer 4WD Switch 5E1-41. . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS5E1-41 . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS5E1-42 . . . . . . . . . . . . . . . . . . . . . .
5E1-2 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
GENERAL DESCRIPTION
The ABS (Antilock Brake System) controls the fluid pressure applied to the wheel cylinder of each brake from the
master cylinder so that each wheel is not locked even when hard braking is applied. This ABS is a 4-wheel type
which controls the fluid pressure applied to the wheel cylinder of each of the four brakes to prevent each wheel
from getting locked.
The component parts of this ABS includes following parts in addition to those of the conventional brake system.

Wheel speed sensor which senses revolution speed of each wheel and outputs its signal.

In this ABS, ABS hydraulic unit (actuator assembly), ABS control module, pump motor relay and fail-safe relay
are combined as one component.

ABS control module which sends operation signal to ABS hydraulic unit to control fluid pressure applied to each
wheel cylinder based on signal from each wheel speed sensor so as to prevent wheel from locking.

ABS hydraulic unit which operates according to signal from ABS control module to control fluid pressure applied
to wheel cylinder of each of 4 wheels.

Fail-safe (solenoid valve) relay which supplies power to solenoid valve in ABS hydraulic unit and pump motor
relay.

Pump motor relay which supplies power to pump motor in ABS hydraulic unit.

ªABSº warning lamp which lights to inform abnormality when system fails to operate properly.

G sensor which detects body deceleration speed. (For 4WD model only)
This ABS is equipped with Electronic Brake force Distribution (EBD) system that controls a fluid pressure of rear
wheels to best condition, which is the same function as that of proportioning valve, by the signal from wheel sensor
independently of change of load due to load capacity and so on. And if the EBD system fails to operate properly,
the brake warning lamp lights to inform abnormality.

YH4
GRAND
VITARA
1. Diagnosis connector
(6 pins connector)
2. Ground terminal3. Diag. switch terminal
4. Service wire
5E1-6 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
ABS HYDRAULIC UNIT/CONTROL MODULE
ASSEMBLY
ABS control module is a component of ABS hydrauli unit / control
module assembly and has the following functions.
Self-Diagnosis Function
ABS control module diagnoses conditions of the system compo-
nent parts (whether or not there is any abnormality) all the time and
indicates the results (warning of abnormality occurrence and DTC)
through the ªABSº warning lamp as described below.
1) When ignition switch is turned ON, ªABSº warning lamp lights for
2 seconds to check its bulb and circuit.
2) When no abnormality has been detected (the system is in good
condition), ªABSº warning lamp turns OFF after 2 seconds.
3) When the vehicle starts to move after the ignition switch is turned
ON (more than one wheel speed sensor signals are inputted),
solenoid valves and motor of ABS hydraulic unit operate once
one after another for electrical check.
During this check, motor operation sound may be heard but that
means nothing abnormal.
4) When an abnormality in the system is detected, ªABSº warning
lamp lights and the area where that abnormality lies is stored in
the memory of EEPROM in ABS control module.
5) When Diag. switch terminal of diagnosis connector (monitor
connector) is grounded, the abnormal area is output as DTC. It
is indicated by flashing of ªABSº warning lamp. (Refer to the
table below. )
ABS WARNING LAMP
SYSTEM CONDITIONDiag. switch
terminal is not
groundedDiag. switch
terminal is
grounded
In good condi-
No trouble in
the pastOFFDTC 12g
tion at presentTrouble occur-
red in the pastOFFHistory DTC
Abnormality
exists at
No trouble in
the pastONCurrent DTC
exists at
presentTrouble occur-
red in the pastONCurrent and
history DTCs
For procedure to clear all DTC's, refer to the item ªDiagnostic
Trouble Code Clearanceº in this section.
Also ABS control module turns ON EBD warning lamp (brake warn-
ing lamp) depending on the trouble that detected by the module and
EBD warning lamp does not indicate DTC as well as ªABSº warning
lamp.
Fail-Safe Function
When an abnormality occurs (an abnormal DTC is detected), ABS
control module turns OFF the fail-safe relay which supplies power
to ABS hydraulic unit. Thus, with ABS not operating, brakes func-
tion just like the brake system of the vehicle not equipped with ABS.

YH4
GRAND
VITARA
5E1-22 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. ABS hydraulic
unit / control
module connector
INSPECTION
STEPACTIONYESNO
1Is G sensor installed floor securely?Go to step 2.Tighten sensor or
bracket screw
securely. If not,
using new screw.
21) Ignition switch OFF.
2) Remove G sensor with bracket.
3) Check for proper connection to G sensor.
4) If OK then check G sensor referring to item
INSPECTION of G sensor.
Is it in good condition?Go to step 3.Replace G sensor.
31) Disconnect connectors from ABS hydraulic unit /
control module assembly (See Fig. 1) and G sensor.
2) Check for proper connection to ABS control module
at terminals ªA14º and ªA4º.
3) If OK, then turn ignition switch ON and measure
voltage between ªB / Wº terminal of sensor
connector and body ground.
Is it 10 ± 14 V?Go to step 4.ªB / Wº circuit open.
4Measure voltage between ªO / Wº terminal of sensor
connector and body ground.
Is it 0 V?Go to step 5.ªO / Wº circuit
shorted to power
circuit.
51) Ignition switch OFF.
2) Check that ªO / Wº circuit is free from open
or short to ground and ªO / Gº circuit.
Is it in good condition? (See Fig. 2)ªO / Gº circuit open.
If circuit is OK, substi-
tute a known-good
ABS hydraulic
unit / control module
assembly.ªO / Wº circuit open
or shorted to
ground or ªO / Gº
circuit.
Fig. 1 Fig. 2

YH4
GRAND
VITARA
5E1-24 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
INSPECTION
STEPACTIONYESNO
11) Disconnect the applicable sensor connector with
ignition switch OFF.
2) Measure resistance between sensor terminals.
Resistance of wheel speed sensor:
1.2 ± 1.6 k
(at 20C, 68F)
3) Measure resistance between each terminal and
body ground.
Insulation resistance: 1M
or higher
Were measured resistance values in step 2) and 3)
as specified? (See Fig. 1)Go to step 2.Replace sensor.
21) Ignition switch OFF.
2) Disconnect connector from ABS hydraulic
unit / control module assembly. (See Fig. 2)
3) Check for proper connection to ABS hydraulic unit /
control module assembly at each sensor terminal.
4) If OK then, turn ignition switch ON and measure
voltage between sensor positive terminal of module
connector and body ground.
Is it 0 V?Go to step 3.Sensor positive
circuit shorted to
power.
31) Ignition switch OFF.
2) Connect connector to sensor.
3) Measure resistance between sensor terminals at
module connector.
4) Measure resistance between sensor positive
terminal and negative terminal of module connector,
between positive terminal and body ground.
Are measured resistance values within each specified
range described in above step 1?Go to step 4.Circuit open or
shorted to
ground.
41) Remove wheel speed sensor.
2) Check sensor for damage or foreign material being
attached.
Is it in good condition? (See Fig. 3)Go to step 5.Clean or replace
sensor.
5Check visually through wheel speed sensor
installation hole for following.

Rotor neither missing or damaged.

No foreign material being attached.

Rotor not being eccentric.

Wheel bearing free from excessive play.
Are they in good condition? (See Fig. 4)Go to step 6.Clean, repair or
replace.
61) Install sensor to knuckle or axle housing.
2) Tighten sensor bolt to specified torque and check
that there is not any clearance between sensor and
knuckle or axle housing. (See Fig. 5)
Replace sensor if any.
Referring to item OUTPUT VOLTAGE INSPECTION of
FRONT WHEEL SPEED SENSOR, check output voltage
or waveform of sensor. Is proper output voltage or
waveform obtained?Substitute a
known-good ABS
hydraulic unit /
control module
assembly and
recheck.Replace sensor
and recheck.