2002 SUZUKI GRAND VITARA Shaft

YH4
GRAND
VITARA
7A
MANUAL TRANSMISSION (TYPE 1) 7A-1
TYPE 1
GENERAL DESCRIPTION7A- 1 . . . . . . . . . . . . . .
DIAGNOSIS7A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7A- 3 . . . . . . . . . . . . . . . .
Gear Oil 7A- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Control Levers 7A- 4. . . . . . . . . . . . . . . . . . .
Switches 7A- 6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting 7A- 8. . . . . . . . . . . . . . . .
Dismounting of Trans. Unit 7A- 9. . . . . . . . . . . . .
Remounting of Trans. Unit 7A-12. . . . . . . . . . . . . Extension Case (2WD MODEL) 7A-13. . . . . . . .
Extension Case Oil Seal
(2WD MODEL) 7A-13. . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7A-14 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7A-14 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7A-14 . . . . . .
SPECIAL TOOL7A-14 . . . . . . . . . . . . . . . . . . . . . . .
As the aluminum case is sealed with liquid type gas-
ket, it is necessary to use genuine sealant or its equiv-
alent on its mating surfaces when reassembling it.
Also, the case fastening bolts must be tightened to
specified torque by means of the torque wrench and
tightening over or below the specified torque should
be avoided.
The description under ON-VEHICLE SERVICE in this
section covers a part of the TYPE 2 manual transmis-
sion and the transfer. The transfer is next to the trans-
mission as well, but their gear boxes are independent
and each of them has its own drain and level / filler
plugs for the oil change or the level check.
For the repair procedure of the transfer unit, refer to
Section 7D.
SECTION 7A
MANUAL TRANSMISSION
(TYPE 1)
CONTENTS
GENERAL DESCRIPTION
The manual transmission consists of the input shaft,
main shaft, countershaft and reverse gear which are
installed in the aluminum case. Its gears are of for-
ward five speeds in synchro mesh and reverse one
speed in constant mesh system.
The main shaft gears are held by the needle bearings
and on them the synchronizer rings and synchronizer
sleeve & hubs are assembled.
The gear shift lever case is located at the upper be-
hind the transmission case and has a cam which pre-
vents direct gear shift from the 5th speed gear to the
reverse gear.

YH4
GRAND
VITARA
7A-2 MANUAL TRANSMISSION (TYPE 1)
DIAGNOSIS
ConditionPossible CauseCorrection
Gear slipping out of mesh
Worn shift fork shaft

Worn shift fork or synchronizer sleeve

Weak or damaged locating spring

Worn bearings on input shaft or main shaft

Worn chamfered tooth on sleeve or gear

Missing or disengagement of circlip(s)Replace
Replace
Replace
Replace
Replace sleeve and gear
Install
Gears refusing to disengage
Weakened or broken synchronizer spring

Distorted shift shaft or shift forkReplace
Replace
Hard shifting
Improper clutch pedal free travel

Distorted or broken clutch disc

Damaged clutch pressure plate

Worn synchronizer ring

Worn chamfered tooth on sleeve or gear

Distorted shift shaftAdjust
Replace
Replace clutch cover
Replace
Replace sleeve and gear
Replace
Noise
Inadequate or insufficient lubricant

Damaged or worn bearing(s)

Damaged or worn gear(s)

Damaged or worn synchronizer ring

Damaged or worn chamfered tooth on
sleeve or gearReplenish
Replace
Replace
Replace
Replace

YH4
GRAND
VITARA
Viscosity chart
SAE
1. Reverse idle gear shaft bolt
(DO NOT LOOSEN IT)
MANUAL TRANSMISSION (TYPE 1) 7A-3
ON-VEHICLE SERVICE
GEAR OIL
INSPECTION AND CHANGE
1) Before changing or inspecting oil, be sure to stop engine and lift
vehicle horizontally.
2) With vehicle lifted up, check oil level and leakage. If leakage ex-
ists, correct or repair it.
3) Drain old oil and fill new specified oil as shown below by speci-
fied amount (roughly up to level hole).
NOTE:

It is highly recommended to use SAE 75W-90 gear oil.

Whenever vehicle is hoisted for any other service work
than oil change, also be sure to check for oil leakage and
status of breather hoses.

If water or rust is mixed in drained oil, be sure to check
breather hose and boot of transmission and transfer.
Gear Oil Specification
Oil grade: API GL-4
Viscosity: SAE 75W-85, 75W-90 or 80W-90
Oil Capacity:
Transmission 1.5 liters (3.2 / 2.6 US / Imp. pt)
Transfer 1.7 liters (3.6 / 3.0 US / Imp. pt)
4) Torque drain plug and level / filler plug as specified below after
applying sealant to its thread.
CAUTION:

Transmission oil must not be poured through gear shift
control lever part.

Do not loosen or remove reverse idle gear shaft bolt.
ªAº: Sealant 99000-31110
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
7A-6 MANUAL TRANSMISSION (TYPE 1)
3, (a)
1. Coupler
2. Clamp3. 4WD switch
4. Boot No. 2
1. Back up light switch
2. 4WD switch
1. Back up light switch coupler
2. Front propeller shaft
SWITCHES
TRANSFER 4WD SWITCH
1) Remove console box and lift transmission control lever boots
No. 2 and No. 3. (Refer to page 7A-4.)
2) Remove transfer control lever boot No. 2, unclamp wiring on
transfer case to free it and pull off coupler.
3) Replace switch and connect as it was.
Tightening Torque
(a): 20 N
.m (2.0 kg-m, 14.5 lb-ft)
4) Turn ON ignition switch, shift transfer shift control lever to 4WD
position and check that indicator lights. Turn OFF switch after
checking.
NOTE:

When removing and reinstalling switch, use care not to let
dust enter transfer box inside.

Make sure to reset clamp for wiring which is located
where invisible directly.

It is recommended to work on transfer shift control lever
boot No. 1 from underside of vehicle on lift.

Identify this switch by its leg part which is different for that
of back up light switch.
BACK UP LIGHT SWITCH
WARNING:
Refrain from work while exhaust center pipe is hot.
REMOVAL AND INSTALLATION
NOTE:
When replacing switch, use care not to let dust enter transmis-
sion through switch hole.
1) Lift up vehicle.
2) Remove coupler(s) for switch wiring.

YH4
GRAND
VITARA
1. Match mark
1. Flange bolt
2. Front propeller shaft
1. Transmission jack
2. Engine rear mounting member
7A-10 MANUAL TRANSMISSION (TYPE 1)
ON LIFT
1) Drain oil from transmission and transfer.
2) Give match marks on joint flange and propeller shaft as shown
in figure. (front and rear)
3) Remove flange bolts of rear propeller shaft universal joint and
pull out propeller shaft.
4) Remove flange bolts of front propeller shaft universal joint and
pull out propeller shaft.
5) Remove clutch operating cylinder from transmission. It is not
necessary to disconnect clutch hose from operating cylinder.
NOTE:

It is not necessary to drain transmission oil when dis-
mounting transmission and transfer for clutch mainte-
nance only.

Work without draining transfer oil is possible if front pro-
peller shaft is dismounted together with transmission and
transfer.
6) Remove clutch housing lower plate.
7) Disconnect couplers from 4WD switch, back up light switch and
speed sensor assembly and release their harness from clamps.
Remove nuts from joint with engine.
8) Apply transmission jack and remove engine rear mounting
member taking off its bolts.
9) After removing mounting member, move rearward transmission
and transfer assemblies placed on jack and then lower them.

YH4
GRAND
VITARA
1. Match mark
7A-12 MANUAL TRANSMISSION (TYPE 1)
REMOUNTING OF TRANS. UNIT
For remounting, reverse dismounting procedure.
Use specified torques as given below.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

For tightening torque of transmission stiffener bolt, refer to
ªENGINE MECHANICALº section.

Set each clamp for wiring, hose and cable securely.

Set clamp for shift control lever boots securely.

After installing clutch operating cylinder, check clutch pedal free
travel. Refer to SECTION 7C1 ªCLUTCHº.

Fill gear oil to transmission and transfer as specified.

Connect battery and check function of engine, clutch and trans.

When installing propeller shaft, align the match marks.

YH4
GRAND
VITARA
MANUAL TRANSMISSION (TYPE 1) 7A-13
1
1. Extension case
2. Select return spring bolt
3. Select return spring (short)
4. Select return spring (long)
5. Guide pin
6. Speed sensor assembly 62,ªAº,(a)
3,ªAº
5,ªAº
5,ªAº
4,ªAº
2,ªAº,(a)
1. Oil seal
2. Extension case
ªBºªAº
1
1
22
EXTENSION CASE (2WD MODEL)
DISASSEMBLY
1) Remove oil seal.
2) Remove select return spring bolts and then springs and guide
pins.
3) Remove speed sensor assembly.
REASSEMBLY
1) Install oil seal.
2) After applying grease, install select guide pins, select return
springs and spring bolts and torque them to specification.
ªAº: Grease 99000-25010
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
After installing, check to make sure that each pin moves smooth-
ly.
3) Install speedometer driven gear case assembly to extension
case.
EXTENSION CASE OIL SEAL (2WD MODEL)
REMOVAL AND INSTALLATION
1) Remove propeller shaft referring to SECTION 4B.
2) Using screwdriver, remove oil seal.
3) Using special tool (A) and plastic hammer, press fit new oil seal
into extension case till oil seal contacts stepped part of extension
case as shown. Be sure to apply grease to oil seal lip.
ªAº: Grease 99000-25010
Special Tool
(A): 09951-16060
4) Clean and inspect sliding portion of propeller shaft front end
(where oil seal contacts) before installation and if even small
dent or scratch exists, correct and clean it again.
Then apply grease inside splines of propeller shaft.
ªBº: Grease 99000-25010
5) Install propeller shaft referring to SECTION 4B.

YH4
GRAND
VITARA
7A1
MANUAL TRANSMISSION (TYPE 2) 7A1-1
TYPE 2
GENERAL DESCRIPTION7A1-1 . . . . . . . . . . . . . .
DIAGNOSIS7A1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7A1-3 . . . . . . . . . . . . . . . .
Gear Oil 7A1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift Control Levers 7A1-4. . . . . . . . . . . . . . . . . . .
Switches 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting 7A1-4. . . . . . . . . . . . . . . . Dismounting / Remounting of
Trans. Unit 7A1-4. . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7A1-4 . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7A1-5 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7A1-5 . . . . . .
The manual transmission consists of the input shaft,
main shaft, counter shaft and reverse gear which are
installed in the aluminum and castings cases. Its
gears are of forward five speeds in synchro mesh and
reverse one speed in sliding idler gear arrangement
system.
The main shaft gears are held by the needle bear-
ings and on them the synchronizer rings and syn-
chronizer sleeve & hubs are assembled.
The gear shift lever case is located at the upper be-
hind the transmission case and has a cam which pre-
vents direct gear shift from the 5th speed gear to the
reverse gear.As the aluminum and castings cases are sealed with
liquid type gasket, it is necessary to use genuine seal-
ant or its equivalent on its mating surfaces when reas-
sembling them. Also, the case fastening bolts must be
tightened to specified torque by means of the torque
wrench and tightening over or below the specified
torque should be avoided.
The description under ON-VEHICLE SERVICE in this
section covers the transfer partially which is next to
the transmission as well, but their gear boxes are in-
dependent and each of them has its own drain and
level / filler plugs for the oil change or the level check.
For the repair procedure of the transfer unit, refer to
Section 7D.
SECTION 7A1
MANUAL TRANSMISSION
(TYPE 2)
CONTENTS
GENERAL DESCRIPTION