2002 SUZUKI GRAND VITARA Wire

YH4
GRAND
VITARA
1. Meter cluster
2. Hazard switch
Terminal
Wire ColorSwitch Position
LH steering vehicle shown
LIGHTING SYSTEM 8B-9
TURN SIGNAL AND HAZARD WARNING
LIGHTS
TURN SIGNAL SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
TLTBTR
G/RGG/Y
L
N
R
REMOVAL AND INSTALLATION
Refer to Section 3C COMBINATION SWITCH for vehicle without air
bag system and Section 3C1 CONTACT COIL AND COMBINA-
TION SWITCH ASSEMBLY for vehicle with air bag system.
HAZARD SWITCH
REMOVAL
1) Remove meter cluster.
2) Pull hazard switch out of instrument panel.
3) Disconnect coupler from hazard switch.
4) Remove hazard switch.
INSTALLATION
Reverse removal procedure.
INSPECTION
Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace siwtch.

YH4
GRAND
VITARA
8C-6 INSTRUMENTATION / DRIVER INFORMATION
KeyPosition
TerminalWire
color
Hard Top Model
Canvas Top Model
ON-VEHICLE SERVICE
IGNITION (MAIN) SWITCH
INSPECTION
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Disconnect main switch lead wire coupler.
4) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace ignition
(main) switch.
+B+ACCIG1-1IG1-2IG2STL1L2K1K2
W/YBlB/WB/WY/BB/YBBGG
OUTLOCKLOCK
ACC
IN
ON
START
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Remove steering column referring to Section 3C1 of this manu-
al. Then remove steering lock / ignition (main) switch from steer-
ing column.
INSTALLATION
1) Install steering lock / ignition (main) switch to steering column.
Install steering column assembly referring to Section 3C1 of this
manual.
2) Enable air bag system. Refer to ENABLING AIR BAG SYSTEM
in Section 10B of this manual.
NOTE:
When installing steering column, special care must be tak-
en for tightening sequence and its torque.

YH4
GRAND
VITARA
8C-10 INSTRUMENTATION / DRIVER INFORMATION
G16
J20
H25
1. ECT sensor
1
ENGINE COOLANT TEMP. (ECT) METER AND
SENSOR
ENGINE COOLANT TEMPERATURE (ECT) METER
INSPECTION
1) Disconnect Y/W lead wire going to ECT sensor.
2) Turn ignition switch ON, and check that ECT meter indicates
COOL.
3) Turn ignition switch OFF.
4) Ground Y/W lead wire through a 3.4 W test bulb (1) as illustrated.
5) Turn ignition switch ON, and check that bulb light up and pointer
(2) moves to hot side.
6) If ECT meter shows no operation, repair or replace defective
parts.
ENGINE COOLANT TEMPERATURE (ECT) SENSOR
REMOVAL AND INSTALLATION
Refer to ECT SENSOR in ON-VEHICLE SERVICE in Section 6E1
(for G16 and J20) or Section 6E2 (for H25) of this manual for details.

YH4
GRAND
VITARA
G16
J20
H25
1. Oil pressure switch
INSTRUMENTATION / DRIVER INFORMATION 8C-11
INSPECTION
1) Warm up ECT sensor (1) observing resistance between sensor
terminal (2) and sensor unit (1). Resistance should be de-
creased with increase of its temperature.
2) Check resistance between sensor terminal (2) and sensor unit
(1) shown below. If check result is not as specified, replace sen-
sor.
Temperature
Resistance
50
C (122
F)136 ± 216

OIL PRESSURE LIGHT
OIL PRESSURE SWITCH
REMOVAL AND INSTALLATION
Refer to OIL PRESSURE CHECK in Section 6A1 (for G16), Section
6A2 (for H25), and Section 6A4 (for J20) of this manual for details.
INSPECTION
1) Disconnect oil pressure switch (1) lead wire.
2) Check for continuity between oil pressure switch terminal (2)
and cylinder block (3) as shown.
During Engine Running
No continuity
At Engine StopContinuity
If check result is not as specified, replace oil pressure switch (1).

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-5
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER
REAR WIPER AND WASHER (IF EQUIPPED)
TroublePossible causeCorrection
Wiper malfunctions
ªWIPER / WASHERº fuse blown (Hard Top
Model)
ªWIPº fuse blown (Canvas Top Model)

Wiper motor faulty

Wiper switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace motor
Replace switch
Repair
Washer malfunctions
Washer hose or nozzle clogged

ªWIPER / WASHERº fuse blown (Hard Top
Model)
ªWIPº fuse blown (Canvas Top Model)

Washer motor faulty

Washer switch faulty

Wiring faultyClean or repair clogged hose or
nozzle
Replace fuse to check for short
Replace motor
Replace switch
Repair
REAR WINDOW DEFOGGER (IF EQUIPPED)
TroublePossible causeCorrection
Defogger does not work
ªREAR DEFGº fuse blown

Defogger switch faulty

Defogger heat wire faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair heat wire
Repair
POWER WINDOW CONTROL SYSTEM
TroublePossible causeCorrection
All power windows do not
operate
ªPOWER WINDOWº fuse blown (Hard Top
Model)
ªP / Wº fuse blown (Canvas Top Model)

Ignition switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair
Only one power window
does not operate
Power window switch (main or sub) faulty

Power window motor faulty

Window lock switch faulty

Wiring or grounding faultyReplace switch
Replace motor
Replace switch
Repair

YH4
GRAND
VITARA
WASHER
ONINT
LO
HI
Type A
Type B
Type C
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-9
Wiper
SW
Terminal
Wiper SW
Terminal
ON-VEHICLE SERVICE
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER
INSPECTION
Front Wiper and Washer Switch (in Combination Switch)
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace
switch.
B3+2+1AsB3+2+1As
OFFB3WINTB3W
LOOFF
HION
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
Wiper Motor
1) As illustrated, use a 12 V battery to connect its (+) terminal to ter-
minal ªAº, and its (±) terminal to Black lead wire (2) (Type A, B)
or terminal ªEº (Type C).
If motor (1) rotates at a low revolution speed of 45 to 55 rpm, it
is proper. For high speed check, connect battery (+) terminal to
terminal ªBº, and its (±) terminal to Black lead wire (2) (Type A,
B) or terminal ªEº (Type C). If motor rotates at a high revolution
speed of 67 to 83 rpm, it is proper.

YH4
GRAND
VITARA
Type B Type A
Type C
1. Washer tank
8D-10 WINDOWS, MIRRORS, SECURITY AND LOCKS
2) Testing automatic stop action.
a) Connect 12 V battery (+) terminal to terminal ªAº of wiper mo-
tor (1) and (±) terminal to Black lead wire (2) (Type A, B) or
terminal ªEº (Type C), and let the motor turn.
b) Disconnect terminal ªAº from battery, and let the motor stop.
c) Connect terminal ªAº and ªDº with a jumper wire (3), and con-
nect terminal ªCº to battery (+) terminal. Observe the motor
turns once again then stops at a given position.
d) Repeat a) thru c) several times and inspect if the motor stops
at the given position every time.
Washer Pump
Connect battery (+) and (±) terminals to pump (+) and (±) terminals
respectively to check pumping rate.
Check for both front (3) and rear (2) (if equipped) washer pump.
Pumping Rate:
Front and Rear (if equipped) more than 1.0 l / min.
(2.1 US pt. / min.,
1.76 lmp pt. / min.).

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-11
SLOW
FAST
10 ± 14 V
0 V
1.6
1 sec.
10 ± 14 V
0 V
10.7
5 sec.
Intermittent Wiper Relay Circuit
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Turn the front wiper switch to INT position.
4) Turn the intermittent time control switch to FAST position.
5) Connect battery positive terminal to terminal ªB3º and battery
negative terminal to terminal ªEº.
6) Connect voltmeter positive lead to terminal ª+1º and negative
lead to terminal ªEº.
Check that the voltmeter indicates the battery voltage (10 ±
14 V).
7) Connect terminal ªAsº and terminal ªB3º by a jumper wire. Then
move jumper wire end connected to terminal ªB3º to terminal ªEº.
Observe the voltmeter voltage drops to 0 V right after connecting
the jumper wire from terminal ªB3º to ªEº. Then the voltage rises
to battery voltage (10 ± 14 V) within the time shown in the table
below.
INT time control
switch position
Voltage
FAST
SLOW