Page 137 of 181
YOUR 807 IN DETAIL127
REAR INTERIOR LAYOUT
1. Access handle
2. Grab handle and coat hook
3. Door tray with storage for a
can and a bottle of water or for
the portable bin with ashtray
4. High load retaining net fasten ings
Open the covers of the upper
fastenings at the 3rd row.
Install the ends of the metal bar
in these fastenings.
Secure the two tray strap hooks
in the stowing rings on the floor.
Pull the two straps taut.
Secure the two hooks on the
elastic parts of the tray in these
rings.
Note: the rings are located
directly below the corresponding
upper fastenings. 5. Storage compartment
6. Can holder
7. Storage compartment
8. Bottle holder or portable bin
with ashtray
9. Luggage retaining net "low load" version fastenings
Fold the net in two.
Secure the two centre hooks in
the stowing rings on the floor.
Secure the net's remaining four
hooks on the tailgate pillars.
10. 12V socket for accessories
11. Luggage retaining net Secure the net's four hooks in
their stowing rings on the floor.
12. Tonneau To install it :
– position one end of the ton neau roller in the 2nd row, – compress the opposite end of
the roller and position it,
– release it to allow it to engage,
– unroll the tonneau as far as the rear shelf,
– secure the two hooks under the rear shelf,
To remove it:
– remove the tonneau hooks under the rear shelf,
– return the tonneau into its roller,
– compress it and remove it from its support at the 2nd row.
13. Rear shelf with umbrella holder
To remove the shelf:
– pull it rearward
– lift it slightly, then remove it
There are several options for
storing it:
– either hooked onto the ton neau
– or behind the seats or the rear bench seat
18-11-2002
Page 155 of 181
PRACTICAL INFORMATION
142
CHANGING A WHEEL
Parking the vehicle
If possible, park the vehicle on
level, stable and non slippery
ground.
Apply the handbrake, switch off
the ignition and engage first or
reverse gear (position Pfor the
automatic gearbox) .
Access to the spare wheel Open the tailgate.
Pull and turn the towing eye to
unlock the lifting tool and access
the bolt.
Unscrew the bolt fully, using the
wheelbrace 1to unwind the lifting
tool cable.
Detach the spare wheel through
the rear of the vehicle.
Take out the hinged hook via the
wheel shaft to release it. Tools
The following tools are located in the
engine compartment
1
Wheelbrace.
2 Jack
3 Removable towing eye.
4 Alloy wheel embellisher remover
Removing the wheel Place a chock 3if possible under
the wheel diagonally opposite to
the one to be changed.
Remove the trim, using the wheel
brace 1, pulling at the valve pas
sage hole.
Loosen the wheel bolts (for vehi
cles fitted with alloy wheels,
remove the wheel embellisher 4).
Remove the cover from the jack
suport holder.
Detach the jack fixing strap and
take it out from the bottom of the
jack support holder.
Place the jack 2in contact with
one of the four locating points A
on the sub frame (the one which
is closest to the wheel to be
changed).
Extend the jack 2until its base is
in contact with the ground. Ensure
that the centre line of the base of
the jack is straight above the
locating point A.
Raise the vehicle.
Unscrew the bolts and remove the
wheel.
18-11-2002
Page 158 of 181
Direction indicator repeaters:
WY 5 W (amber). Push the repeater rearwards and
release it from the mirror.
Hold the connector and turn the
bulb holder a quarter turn to the
left.
Turn the bulb a quarter turn to
the left, remove it and change it.
When refitting, engage the
repeater towards the rear and
move it towards the front of the
mirror. Rear lights
1 Direction indicators:
PY 21 W
(amber) .
2 Brake/side lights: P 21/5 W.
3 Reversing lights: P 21 W.
4 Fog lamps: P 21 W.
These 4 bulbs are changed from
inside the vehicle: open the tailgate,
remove the air extraction grille on
the side concerned,
unclip the light harness,
unscrew the two interior nuts and
remove the light,
unscrew the bulb holder concer
ned an eighth turn to the left and
remove it,
unscrew the faulty bulb an eighth
turn to the left and change it. When refitting:
take care to position the bulb cor
rectly and press on it to engage it,
take care to position the bulb hol
der correctly and press on it to
engage it,
take care to position and secure
the light correctly.
Number plate lights:
W 5 W Remove the lens.
Change the faulty bulb.
PRACTICAL INFORMATION 145
Third brake light:
5 W 5 W bulbs. Remove the tailgate upper trim by
unclipping it on either side.
Squeeze the two tabs 1to release
the bulb holder.
Change the faulty bulb.
When refitting, ensure that the
tailgate upper trim has been put
back in place correctly.
Note: when two or more bulbs are
faulty, you must replace them imme
diately.
Amber coloured bulbs
(direction indicators and
side repeaters), must be
changed for bulbs of iden
tical specification and
colour.
18-11-2002
Page 159 of 181
Direction indicator repeaters:
WY 5 W (amber). Push the repeater rearwards and
release it from the mirror.
Hold the connector and turn the
bulb holder a quarter turn to the
left.
Turn the bulb a quarter turn to
the left, remove it and change it.
When refitting, engage the
repeater towards the rear and
move it towards the front of the
mirror. Rear lights
1 Direction indicators:
PY 21 W
(amber) .
2 Brake/side lights: P 21/5 W.
3 Reversing lights: P 21 W.
4 Fog lamps: P 21 W.
These 4 bulbs are changed from
inside the vehicle: open the tailgate,
remove the air extraction grille on
the side concerned,
unclip the light harness,
unscrew the two interior nuts and
remove the light,
unscrew the bulb holder concer
ned an eighth turn to the left and
remove it,
unscrew the faulty bulb an eighth
turn to the left and change it. When refitting:
take care to position the bulb cor
rectly and press on it to engage it,
take care to position the bulb hol
der correctly and press on it to
engage it,
take care to position and secure
the light correctly.
Number plate lights:
W 5 W Remove the lens.
Change the faulty bulb.
PRACTICAL INFORMATION 145
Third brake light:
5 W 5 W bulbs. Remove the tailgate upper trim by
unclipping it on either side.
Squeeze the two tabs 1to release
the bulb holder.
Change the faulty bulb.
When refitting, ensure that the
tailgate upper trim has been put
back in place correctly.
Note: when two or more bulbs are
faulty, you must replace them imme
diately.
Amber coloured bulbs
(direction indicators and
side repeaters), must be
changed for bulbs of iden
tical specification and
colour.
18-11-2002