2002 Peugeot 607 Dag bulb

INSTRUMENTS AND CONTROLS35
Engine diagnostics warning light
This is linked to the warning light on the instrument pane
l.
Display of this warning light is accompanied by an audible si gnal and the message 'Engine emission control sys
tem faulty' on the multifunction display.
If it flashes when the engine is running, this indicates a malfunction in the injection, ignition or emission control system. There
is a risk of damage to the catalytic converter (petrol engine onl y).
Contact a PEUGEOT dealer as soon as possible.
Bulb blown warning light
Display of this indicator light is accompanied by an audible signal and the message 'Bulb... faulty' on the multifunc
tion display, indicating the faulty bulb: a bulb in th e dipped beam lights, the side lights, the direction indi cator lights
(except side repeaters) or the brake lights (except the central brake light).
Change the faulty bulb.
Windscreen/headlamp wash reservoir warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Screenwash low'on the multi
function display.
Fill the windscreen/headlamp wash reservoir the next time you st op.
Particulate emission filter saturation warning light (diesel engine)
Display of this warning light is accompanied by an audible si gnal.
When it occurs with the engine running, this indicates the start of saturation of the particulate emission filter (excep
tionally long periods of town type driving conditions: reduce d speed, long tailbacks...).
To regenerate the filter, you are advised to drive as soon as possible and when traffic conditions permit at a speed of 35 mph
(60 km/h) or more for at least five minutes (until the warning li ght goes out).
If the light remains on, contact a PEUGEOT dealer.
Note: After prolonged operation of the vehicle at a very low speed or at idle, you may sometimes notice steam coming from
the exhaust during acceleration. This has no effect on the p erformance of the vehicle or on the environment.

PRACTICAL INFORMATION 143
CHANGING A BULB
Front lights
In the engine compartment, remove the style cover secured
by one or two butterfly screws, a plastic retainer clip and
two screws.
Note:
handle the bulbs with a dry cloth.
1 Dipped beam headlamps: H755W or Xenon bulb.
WARNING: RISK OF ELECTROCUTION
Xenon bulbs must be replaced by a PEUGEOT
dealer.
2 Main beam headlamps: H155W.
 Turn the protective cover of the faulty bulb a quarter
of a turn and remove it.
 Disconnect the connector.
 PPress the end of the securing clip to free it. Change
the bulb.
 When fitting the new bulb, ensure that the direction
notches are positioned correctly and the securing
clip is fixed properly. 
Reconnect the connector.
 Refit the protective cover.
The headlamps are fitted with polycarbonate glass with a
protective coating. Do not clean them with a dry or abra
sive cloth, nor with a detergent or solvent product.
3 Side lights: W 5 W.
 Pull the socket rearwards, remove the bulb and
change it.
4 Direction indicators: PY 21 W (amber).
 Turn the bulb holder a quarter turn and remove it.
 Change the bulb.
 Refit the style cover.
Front foglamps: H1 55 W.
Note: In certain climatic conditions (low temperature,
humidity), condensation on the inside surface of the
headlamp glass is normal ; it disappears a few minutes
after the lights are switched on.

Rear lights
Rear wing lights
1 Direction indicators: PY 21 W (amber).
2 Brake lights/side lights: P21/5 W.
 Detach the luggage net.
 Lift the boot carpet with the lifting
hook. Secure this hook behind
the boot seal.
 Unclip the lower part of the sill
trim, then dislodge it by pulling
upwards.
 Remove the plastic retainer clip
securing the side trim to the
floor. 
Unclip the side trim.
 Remove the two butterfly nuts
securing the light.
 Remove the eyelet.
 Take out the lamp.
 Turn the lamp holder a quarter
turn.
 Change the faulty bulb.
 Lock the bulb holder in place.
When refitting it, ensure that the
lamp is correctly positioned and
secured.
PRACTICAL INFORMATION
144
Direction indicator repeaters:
WY 5 W (amber).
 Push the repeater forwards or
backwards and release the
assembly.
 Hold the connector and turn the
transparent cover a quarter turn.
 Change the bulb.
Amber coloured bulbs
(direction indicators and
side repeaters) must be
replaced with bulbs of
identical specification and
colour.

Rear lights
Rear wing lights
1 Direction indicators: PY 21 W (amber).
2 Brake lights/side lights: P21/5 W.
 Detach the luggage net.
 Lift the boot carpet with the lifting
hook. Secure this hook behind
the boot seal.
 Unclip the lower part of the sill
trim, then dislodge it by pulling
upwards.
 Remove the plastic retainer clip
securing the side trim to the
floor. 
Unclip the side trim.
 Remove the two butterfly nuts
securing the light.
 Remove the eyelet.
 Take out the lamp.
 Turn the lamp holder a quarter
turn.
 Change the faulty bulb.
 Lock the bulb holder in place.
When refitting it, ensure that the
lamp is correctly positioned and
secured.
PRACTICAL INFORMATION
144
Direction indicator repeaters:
WY 5 W (amber).
 Push the repeater forwards or
backwards and release the
assembly.
 Hold the connector and turn the
transparent cover a quarter turn.
 Change the bulb.
Amber coloured bulbs
(direction indicators and
side repeaters) must be
replaced with bulbs of
identical specification and
colour.

145
PRACTICAL INFORMATION
Boot lid lights
1 Reversing lights: P 21 W.
2 Fog lamps: P 21 W.
 Remove the three plastic retain
er clips securing the cover trim
(those nearest to the lamp).
 Move aside the trim. 
Turn the bulb holder a quarter
turn.
 Change the faulty bulb. Number plate lights:
W 5 W.
 Remove the transparent cover
using a screwdriver blade.
 Change the faulty bulb.

PRACTICAL INFORMATION
154
T
OWING A TRAILER,
CARAVAN, BOAT ETC...
Only use original PEUGEOTtow
bars which have been tested and
approved from the design stage of
your vehicle.
The tow bar must be fitted by a
PEUGEOTdealer.
Driving advice
Distribution of loads: distribute the
load in the trailer so that the heaviest
loads are as close as possible to the
axle and the nose weight is close to
the maximum authorised without,
however, exceeding it.
Cooling: towing a trailer on a slope
increases the coolant temperature.
As the fan is electronically con
trolled, its cooling capacity is not
dependent on the engine speed.
On the contrary, use a high gear to
lower the engine speed, and reduce
your speed. In all cases, pay attention to the
coolant temperature.
Note:
in certain cases of particularly
arduous use (towing the maximum
load up a steep slope in high tem
peratures), the engine automatically
limits its power. In this case, cutting
off the air conditioning allows the
engine power to be recovered, and
therefore the towing speed to be sig
nificantly increased (approximately
12mph [20 km/h] more).
If the coolant temperature warning
light comes on, stop the vehicle and
switch off the engine as soon as pos
sible.
Tyres: check the tyre pressures of
the towing vehicle and of the trailer,
observing the recommended pres
sure.
Brakes: towing increases the brak
ing distance. Drive at a moderate
speed, change down early and brake
gradually.
Side wind: sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed. Lighting
Manual adjustment
Adjust your headlamps so as not to
dazzle other road users (see section
on ''Manual adjustment of head
lamps''). Check the electrical sig
nalling of the trailer.
Automatic beam correction
For vehicles with Xenon bulbs, this
system automatically corrects the
height of the beam, whatever the
load of the vehicle. The driver is then
assured of having optimum lighting
and not causing a nuisance to other
road users.
In cases of malfunction, the driver is
alerted by means of the warning light
on the instrument panel.
In this situation the system adjusts
your headlamps to the low position.