2002 Peugeot 406 C tyre pressure

MAINTENANCE OF YOUR 406 COUPE23

All driving conditions. oArduous conditions.
A AND C SERVICES AND THE INTERMEDIATE VISIT
- Oil filter- Fuel filter(Petrol)- Fuel filter element (diesel only).- Air filter element- Spark plugs (petrol only)
- Engine oil- Bleed fuel filter (diesel only)
- Engine oil (check + top-up)- Gearbox oil (check + top-up)- Battery (check + top-up)- Front/rear screen wash (check + top-up )- Coolant (check + top-up)- Brake fluid (check + top-up)- Power steering fluid (check + top-up according to specification)- Operation of lights and indicators- Condition of glass, headlamp & light lenses and mirrors- Horn- Windscreen washer jets- Condition of wiper blades- Condition and tension of the ancillary drive belts- Handbrake- Condition of hydraulic circuits (hoses and covers)- Condition of rubber boots and gaiters- Brake pads o- Play in hubs, link rods, ball joints, flexible mountings- Shock absorbers- Rear drum brake lining wear- Condition and pressure of tyres (including spare wheel)- Emission control check according to current legislation (petrol only)- Smoke opacity (diesel only) - Pollen filter (according to specification)o- Visual check of the whole vehicle by a Peugeot technician
DRAIN and REFILL
REPLACE
LEVELS
CHECK

ROAD TEST
- Courtesy vehicle
SERVICE
LevelOperation Description of Operation First Service
A C Intermediate
01-07-2002

DRIVING YOUR 406 COUPE
124
CRUISE CONTROL Cruise control enables the vehicle to maintain a steady speed pro-
grammed by the driver, regardless ofthe road characteristics and withoutthe driver having to touch the accel-erator or brake pedals. In order for it to be memorised, the vehicle speed must be greater thanapproximately 25 mph (40 km/h). Operation
Place switch
1 in the ON position.
A speed can be memorised.
Place switch 1 in the OFF position
to cancel.
Memorising a speed As soon as you reach the chosen speed, press button 2or 3. This
memorises the speed, which will be
maintained automatically. Note: It is possible to accelerate
momentarily without disarming the cruise control. Cancelling the memorisedspeed If you wish to cancel the memorised speed:
Press button
4or the brake or
clutch pedal.
Recalling the memorised speed After cancellation, press button 4.
Your vehicle will return to the last memorised speed. Changing a memorised speed
To memorise a speed higher than the previous one:
press button 3;release it when you have reached the required speed.
To memorise a speed lower than theprevious one:
press button 2;
release it when you have reached the required speed.
Cancelling the cruise control
place switch 1in the OFFposition
or switch off the ignition.
Do not use cruise control on slippery roads or inheavy traffic. THE ABS ANTI-LOCKBRAKINGSYSTEM
When used with approved tyres in
good condition, the ABS increasesthe stability and manoeuvrability ofyour vehicle, particularly on poor orslippery road surfaces. The anti-lock braking system comes into operation automatically whenthere is a risk of wheel lock.
EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system enables the optimum braking pres-
sure to be reached more quickly,thus reducing the stopping distance.It is triggered according to the speed
of activation of the brake pedal. The
effect of this is a reduction in theresistance of the pedal and an
increase in braking efficiency. The normal operation of the ABSmay make itself felt by slightvibrations of the brake pedal. In emergency braking, press very firmly without releasingthe pressure.
01-07-2002

- The jack is fitted with a systemwhich enables it to be folded or
unfolded rapidly.
- Take the jack from the toolkit and close it by pressing the ends A.
- Place the jack at one of the loca- tions Eunderneath the vehicle, as
close as possible to the wheel tobe changed. Unfold it by pulling theends A.
- Extend the jack using the wheel- brace 1and the extension 3.
- Take out a wheel bolt at the top and fit the centralising tool 2.
- Loosen the wheel bolts and remo- ve the wheel. Fitting a wheel
- Position the wheel using the cen-
tralising tool to assist you.
- Tighten the bolts by hand, and remove the centralising tool.
- Partly tighten the bolts using the wheelbrace.
- Fold the jack and remove it.
- Fully tighten the wheel bolts using the wheelbrace.
- Replace the centre trim by pres- sing it with the palm of your hand.
MAINTENANCE OF YOUR 406 COUPE 33
For your safety, always change the wheel:
- on level, stable, non-slipperyground,
- with the handbrake applied,
- with first or reverse gear enga- ged (position Pfor the automatic
gearbox).
Never go underneath a vehicle which is supported only by a jack(use a ramp). After changing the wheel - have the tightening of the bolts and the tyre pressure checkedby a PEUGEOT dealer as soonas possible,
- have the punctured tyre repai- red and refit it to the vehicle assoon as possible.
01-07-2002

Towing a trailer, caravan, boat etc.
Only use original PEUGEOT tow bars that have been tested andapproved from the design stage of
your vehicle. The tow bar must be fit-
ted by a PEUGEOT dealer.
Your vehicle is basically designed fortransporting people and luggage but it
may also be used for towing a trailer.
Driving with a trailer subjects thetowing vehicle to more significantstress and its driver must be particu-larly careful. Air density decreases with altitude, thus reducing engine performance.Above 1000 metres, the maximumtowing load must be reduced by 10%and so on for every 1000 metres ofaltitude.Driving advice Distribution of loads Distribute the load in the trailer so that the heaviest items are as closeas possible to the axle and the noseweight approaches the maximumpermitted without exceeding it. Cooling
Towing a trailer on a slope increases the temperature of the coolant. As the fan is electrically controlled, its cooling capacity is not dependenton the engine speed.
On the contrary, use a high gear to lower the engine speed, and reduceyour speed. The maximum towing load on a long slope depends on the gradient andthe outside temperature. In all cases, pay attention to the coolant temperature. If the warning light comes on, stop
the vehicle and switch off the engineas soon as possible.Tyres Check the tyre pressures of the tow-
ing vehicle and of the trailer, observ-ing the recommended pressures. Braking
Towing increases the braking dis-tance. Lights Check the electrical signalling on the
trailer. Side wind
Take into acount the increased sen-sitivity to side wind.
MAINTENANCE OF YOUR 406 COUPE
45
01-07-2002

THE IDENTIFICATION FEATURES OF YOUR 406 COUPE
A. Manufacturer's plate.
B. Model serial number on the bodywork.
C. Paint colour reference.
D. Serial number on the fascia.
E. Tyre pressure label.Tyres The tyre pressure label
Eon the dri-
ver's door pillar, near the hinges, gives:
Ð the wheel and tyre sizes,
Ð the brands of tyres approved by the manufacturer,
Ð the tyre pressures.The tyre pressure must be checked when cold, at least once a month.
Tyre sizes fitted as standard:
Ð 215/55 R 16 V for vehicles fitted with the 2.2 litre 16V and 3 litre 24V V6 petrol engines and the2.2 litre 16V HDI diesel engine.
Ð 205/55 R 16 for vehicles fitted with the 2 litre 16V petrol engine.
Ð winter tyres for all engines: Michelin Pilot Alpin 205/55 R 16.
TECHNICAL DATA
134
01-07-2002