Page 109 of 128
CHANGING A BULB Front lights Note:on the right side, remove the style cover, fixed with
two plastic screws, to access the bulbs. Handle the bulbs with a dry cloth.
1 - Dipped beam headlamps (H7-55 W),
2 - Main beam headlamps (H1-55 W),
3 - Front fog lamps* (H1-55 W). Turn the protective cover corresponding to the faulty bulb a quarter of a turn and remove it.
Disconnect the connector.
Press the end of the securing clip to free it. Changethe bulb. When fitting the new bulb, ensure that the direction notches are positioned correctly and that the securing
clip is fixed properly.
Reconnect the connector.
Refit the protective cover, positioning it with the arrowupwards, then turn it a quarter of a turn to the right. The headlamps are fitted with polycarbonate glass with aprotective coating.
Do not clean them with a dry or
abrasive cloth, nor with a detergent or solvent pro-duct. Use a sponde and soapy water.
4 - Side lights (W 5 W). Pull the socket rearwards, remove the bulb and change it
5 - Direction indicators (PY 21 W amber). Turn the bulb holder a quarter of a turn and remove it.
Change the bulb.
Note: In certain climatic conditions (low temperature,
humidity), condensation inside the headlamp glass is
normal ; it disappears a few minutes after the lights are
switched on.
* According to specification
PRACTICAL INFORMATION
104
Page 110 of 128
Direction indicator repeaters:
(WY 5 W amber). Push the repeater forwards and
release the assembly.
Hold the connector and turn thelens a quarter of a turn.
Change the bulb. Rear lights
1 - Direction indicators (P 21 W).
2 - Reversing lights (P 21 W), right
side.
Fog lamp (P 21 W), left side.
3 - Brake lights (P 21 W).
4 - Side lights (R 5 W). These 5 bulbs are changed from inside the boot: Raise and hook up the boot mat,
Remove the boot sill trim, which is fixed by two plastic nails,
Move aside the boot trim to
access the bulb holder,
Press the tab and remove the
bulb holder,
Change the faulty bulb.
When refitting, take care to pass thetrim under the seal. Third brake light (4 W 5 W bulbs)
Using a 10 mm spanner, unscrew the 2 fixing nuts 1.
Relelase the lamp unit bypushing it outwards.
Squeeze the two tabs 2to relea-
se the bulb holder.
Change the faulty bulb.
When refitting, ensure that thelamp unit seal has been put back
in place correctly.
Number plate lights (W 5 W)
Remove the lens.
Change the faulty bulb.
PRACTICAL INFORMATION 105
Amber coloured bulbs (direction indicators andside repeaters), must bereplaced by bulbs of iden-tical specification and
colour.
Page 111 of 128
Direction indicator repeaters:
(WY 5 W amber). Push the repeater forwards and
release the assembly.
Hold the connector and turn thelens a quarter of a turn.
Change the bulb. Rear lights
1 - Direction indicators (P 21 W).
2 - Reversing lights (P 21 W), right
side.
Fog lamp (P 21 W), left side.
3 - Brake lights (P 21 W).
4 - Side lights (R 5 W). These 5 bulbs are changed from inside the boot: Raise and hook up the boot mat,
Remove the boot sill trim, which is fixed by two plastic nails,
Move aside the boot trim to
access the bulb holder,
Press the tab and remove the
bulb holder,
Change the faulty bulb.
When refitting, take care to pass thetrim under the seal. Third brake light (4 W 5 W bulbs)
Using a 10 mm spanner, unscrew the 2 fixing nuts 1.
Relelase the lamp unit bypushing it outwards.
Squeeze the two tabs 2to relea-
se the bulb holder.
Change the faulty bulb.
When refitting, ensure that thelamp unit seal has been put back
in place correctly.
Number plate lights (W 5 W)
Remove the lens.
Change the faulty bulb.
PRACTICAL INFORMATION 105
Amber coloured bulbs (direction indicators andside repeaters), must bereplaced by bulbs of iden-tical specification and
colour.