2002 PEUGEOT 206 remove seats

72
9YOUR 206 AT A GLANCE
SEATS Fold-down seat back (all models)
Ð Remove the head restraint,
Ð Tilt the modifiable seat,
Ð Push one of the handles 1
towards the rear to fold down the seat back until it is in a hori-zontal position.
Modifiable passenger seat
Storage compartment
Ð Push the seat as far back as possible,
Ð Raise then pull the front of the seat to unlock it, then tilt the modifiable seat.
3-door version
only.
17-06-2002

7675
10YOUR 206 AT A GLANCE
Rear seats ➜Lift the front of the seat cushion 1,
➜ Tilt the seat cushion 1against the front seats,
➜ Position the seat belt under the belt holder 2,
➜ Pull control 3to unlock the seat back 4,
➜ Remove or lower the head restraint,
➜ Tilt the seat back 4.
When refitting, take care not to trap the seat belts.
Removing the modifiable front passenger seat ➜
Push the seat as far back as possible,
➜ Raise then pull the front of theseat to unlock it,
➜ Tilt the seat,
➜ By pulling upwards, tilt theseat from left to right to makeit easier to remove.
17-06-2002

7675
10YOUR 206 AT A GLANCE
Rear seats ➜Lift the front of the seat cushion 1,
➜ Tilt the seat cushion 1against the front seats,
➜ Position the seat belt under the belt holder 2,
➜ Pull control 3to unlock the seat back 4,
➜ Remove or lower the head restraint,
➜ Tilt the seat back 4.
When refitting, take care not to trap the seat belts.
Removing the modifiable front passenger seat ➜
Push the seat as far back as possible,
➜ Raise then pull the front of theseat to unlock it,
➜ Tilt the seat,
➜ By pulling upwards, tilt theseat from left to right to makeit easier to remove.
17-06-2002

YOUR 206 IN DETAIL73
The adjustment is correct when the upper edge of thehead restraint is level withthe top of the head.
The head restraint is fitted with aframe with notches, which pre-vent the head restraint droppingdown (this is a safety device inthe case of impact).
To lower the head restraint, it is necessary to push simultaneously:
Ð the button located at the base of the head restraint frame,
Ð the head restraint downwards.
To remove the head restraint, press the lug.
Never drive with thehead restraints removed;they should be in placeand correctly adjusted. Rear head restraints These have one position for when they are being used (high) and a
storage position (low). They canbe removed.
To lower the head restraints, press the lug.
To remove them, pull upwards as far as the stop then press therelease control.
FRONT SEATS
1. Forwards-backwards
adjustment Lift the control and slide the seat forwards or backwards.
2. Access to rear seats (3 door) Place your fingers in one of the two handles and push forwards tofold the seat back and move theseat forwards. On repositioning,the seat returns to its initial posi-tion. It is impossible to access the rear seats if the front seat is in thereclining position.
3. Seat back angle adjustment Push one of the two handles
towards the rear.
4. Seat height adjustment Pull the handle upwards. Remove your weight from the seat to raise, or press on the seat
to lower.
5. Head restraint height adjustment
To raise the restraint, push it upwards. Press the switch again to stop operation.
17-06-2002

YOUR 206 IN DETAIL73
The adjustment is correct when the upper edge of thehead restraint is level withthe top of the head.
The head restraint is fitted with aframe with notches, which pre-vent the head restraint droppingdown (this is a safety device inthe case of impact).
To lower the head restraint, it is necessary to push simultaneously:
Ð the button located at the base of the head restraint frame,
Ð the head restraint downwards.
To remove the head restraint, press the lug.
Never drive with thehead restraints removed;they should be in placeand correctly adjusted. Rear head restraints These have one position for when they are being used (high) and a
storage position (low). They canbe removed.
To lower the head restraints, press the lug.
To remove them, pull upwards as far as the stop then press therelease control.
FRONT SEATS
1. Forwards-backwards
adjustment Lift the control and slide the seat forwards or backwards.
2. Access to rear seats (3 door) Place your fingers in one of the two handles and push forwards tofold the seat back and move theseat forwards. On repositioning,the seat returns to its initial posi-tion. It is impossible to access the rear seats if the front seat is in thereclining position.
3. Seat back angle adjustment Push one of the two handles
towards the rear.
4. Seat height adjustment Pull the handle upwards. Remove your weight from the seat to raise, or press on the seat
to lower.
5. Head restraint height adjustment
To raise the restraint, push it upwards. Press the switch again to stop operation.
17-06-2002

YOUR 206 IN DETAIL
76
REAR SEATS
To fold the rear seat(s):
Ð lift the front of the seat cushion
1,
Ð tilt the seat cushion 1against the front seats,
Ð position the seat belt under the belt holder 2,
Ð pull control 3to unlock the seat back 4,
Ð remove or lower the head restraint,
Ð tilt the seat back 4.
Always start with the seat, never the seat back (risk of damage). When repositioning:
Ð fold up the seat back,
Ð fold back the seat cushion,
Ð reposition the lap belt and the buckles before locking the front of the seat cushion.
Take care not to trap the seat belts.
17-06-2002

YOUR 206 IN DETAIL77
Removing the rear seat
Ð Tilt the seat cushion against the front seats.
Ð Squeeze the seat fasteners to release them from their attach- ments.
Ð Remove the seat cushion. TRANSPORTING LONG OBJECTS
To allow the transportation of long objects: Front seat:
Ð remove the modifiable seat (see
corresponding paragraph) and fold down the seat back.
Rear seat:
Ð remove the seat cushion,
Ð tilt the seat back.
17-06-2002

YOUR 206 IN DETAIL
100
Stowing rings Use the stowing rings on the boot floor and on the back of the rear seatto secure your luggage. Luggage retaining net Hooked onto the stowing rings, this enables your luggage to be secured.
BOOT LAYOUT (Saloon)
Retaining strap
A strap secured to the side of the boot enables you to secure variousobjects (cans, first aid kit etc.).
Rear parcel shelf
To remove the shelf:
Ð unhook the two strings 1,
Ð slightly raise the shelf, then remo- ve it.
There are several options for storing the shelf:
Ð either behind the front seats,
Ð or behind the rear seat using theluggage retaining net,
Ð or flat in the boot.
17-06-2002