2002 Oldsmobile Bravada reset

2-83 Trip Information Button
Use the trip information button to scroll through the
odometer, TRIP A, TRIP B and TIMER.
Odometer
Press the trip information button until the odometer
appears on the display. This shows the total distance
the vehicle has been driven in either miles or kilometers.
Pressing the reset stem located on the instrument cluster
with the vehicle off will also display the odometer.
Trip A and Trip B
Press the trip information button until TRIP A or TRIP B
is displayed. This shows the current distance traveled since
the last reset for each trip odometer in either miles or
kilometers. Both odometers can be used at the same time.
Each trip odometer can be reset to zero separately by
pressing select while the desired trip odometer is
displayed. You can also reset the trip odometers with the
reset stem on the cluster. If you press and hold the reset
stem for four seconds, the display will show the distance
traveled since the last ignition cycle.Timer
The DIC can be used as a stopwatch. Press the select
button while TIMER is displayed to start the timer.
The display will show the amount of time that has
passed since the timer was last reset (not including time
the ignition is off). Time will continue to be counted
as long as the ignition is on, even if another display is
being shown on the DIC. The timer will record up to
99 hours, 59 minutes and 59 seconds (99:59:59) after
which the display will roll back to zero.
To stop the counting of time, press the select button
briefly while TIMER is displayed.
To reset the timer to zero, press and hold the select
button while TIMER is displayed.

2-84 Fuel Information Button
Use the fuel information button to scroll through the
range, average fuel economy, instant fuel economy and
the GM Oil Life System
.
Fuel Range
Press the fuel information button until RANGE appears
to display the remaining distance you can drive without
refueling. It's based on fuel economy and the fuel
remaining in the tank. The display will show LOW if the
fuel level is low.
The fuel economy data used to determine fuel range is
an average of recent driving conditions. As your driving
conditions change, this data is gradually updated.
Fuel range cannot be reset.Average Fuel Economy
Press the fuel information button until AVG appears in
the display. Average fuel economy is how many miles
per gallon your vehicle is getting based on current and
past driving conditions.
Press and hold the select button while AVG. ECON is
displayed to reset the average fuel economy. Average
fuel economy will then be calculated starting from that
point. If the average fuel economy is not reset, it will be
continually updated each time you drive.
Instant Fuel Economy
Press the fuel information button until INST appears in
the display. Instant fuel economy is how many miles per
gallon your vehicle is at the particular moment in time.
The instant fuel economy cannot be reset.

2-85
GM Oil Life System

Press the fuel information button until ENGINE OIL
LIFE appears in the display. The GM Oil Life System

shows an estimate of the oil's remaining useful life.
It will show 100% when the system is reset after
an oil change. It will alert you to change your oil on
a schedule consistent with your driving conditions.
Always reset the engine oil life after an oil change.
To reset the Oil Life System press and hold the
select button while ENGINE OIL LIFE is displayed.
Be careful not to reset the engine oil life accidentally at
any time other than when the oil has just been changed.
It can't be reset accurately until the next oil change.
The DIC does not replace the need to maintain your
vehicle as recommended in the Maintenance Schedule
in this manual. Also, the oil change reminder will not
detect dusty conditions or engine malfunctions that may
affect the oil. If you drive in dusty areas, change your
oil after every 3,000 miles (5 000 km) or three months,
whichever occurs first, unless the DIC instructs you to
do so sooner. Also, the oil change reminder does not
measure how much oil you have in your engine. So,
be sure to check your oil level often. See ªEngine Oilº
in the Index.Personalization Button
You can program certain features to a preferred setting
for up to two people. Press the personalization button
to scroll through the following personalization features.
All of the personalization options may not be available
on your vehicle. Only the options available will be
displayed on your DIC.

ALARM WARNING TYPE

AUTOMATIC LOCKING

AUTOMATIC UNLOCKING

SEAT POSITION RECALL (If Equipped)

PERIMETER LIGHTING

REMOTE LOCK FEEDBACK

REMOTE UNLOCK FEEDBACK

HEADLAMPS ON AT EXIT

TILT MIRROR IN REVERSE (If Equipped)

EASY EXIT SEAT (If Equipped)

DISPLAY UNITS (E/M)

DISPLAY LANGUAGE
The driver's preferences are recalled by pressing the
unlock button on the remote keyless entry transmitter
or by pressing the appropriate memory button 1 or 2
located on the driver's door.

2-92
Display Language
To select your personalization for display language,
press the select button while DISPLAY LANGUAGE
is displayed on the DIC. Pressing the select button will
scroll through the following languages:

English

French

Spanish

German

Arabic

Portuguese

Japanese

Italian
Arabic, Portuguese, Japanese and Italian will only be
available as choices if they are enabled in the vehicle.
Choosing any of the above languages will display all of
the information on the DIC in the desired language.If you accidentally choose a language that you don't
want or understand, press and hold the personalization
button and the trip information button and the
same time. The DIC will begin scrolling through the
languages in their particular language. English will
be in English, French will be in French and so on.
When you see the language that you would like,
release both buttons. The DIC will then display the
information in the language you chose.
Choose one of the eight options and press the
personalization button while it is displayed on the
DIC to select it.
Select Button
The select button is used to reset certain functions and
turn off or acknowledge messages on the DIC display.
The select button also toggles through the options
available in each personalization menu. For example,
this button will reset the trip odometers, turn off the
FUEL LEVEL LOW message, and toggle through
the languages you can select the DIC to display
information in.

3-12
Finding a Station
AM FM: Press this button to switch between AM,
FM1 and FM2. The display shows your selection.
TUNE RCL P
-TYPE: Turn this control to select
radio stations.
SEEK SCAN: To seek, press the right pointing or left
pointing arrow to go to the next or previous station and
stay there. The sound will mute while seeking.
To scan, press and hold the SEEK SCAN button for
two seconds until the SC icon appears on the display and
you hear a beep. Use scan to listen to stations for a few
seconds. The radio will go to a station, stop for a few
seconds, then go on to the next station. Press the SEEK
SCAN button again to stop scanning. The sound will
mute while scanning and SC will appear on the display.
To scan your preset stations, press and hold the SEEK
SCAN button for more than four seconds, PRESET
SCAN will appear on the display. You will hear a
double beep and the P will blink with the preset number.
Use preset scan to listen to each of your preset stations
for a few seconds. The radio will go to the first preset
station stored on your pushbuttons, stop for a few
seconds, then go on to the next preset station. Press the
SEEK SCAN button again to stop scanning presets.Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2), by performing the
following steps:
1. Turn the radio on.
2. Press AM FM to select the band.
3. Tune in the desired station.
4. Press AUTO EQ to select the equalization that best
suits the type of station selected.
5. Press and hold one of the six numbered pushbuttons
until you hear a beep. Whenever you press that
numbered pushbutton, the station you set will
return and the equalization that you selected will
also be automatically selected for that pushbutton.
6. Repeat the steps for each pushbutton.

3-13
Setting the Tone (Bass/Treble)
AUDIO: To set the bass, press and hold the AUDIO
button until BASS appears on the display. Press the
knob above the AUDIO button to extend it then turn
the knob to increase or decrease bass. When you use
this knob, the radio's tone setting will switch to manual.
To set the midrange, press and hold the AUDIO button
until MID appears on the display. Press the knob above
the AUDIO button to extend it then turn the knob to
increase or decrease bass. When you use this knob,
the radio's tone setting will switch to manual.
To set the treble, press and hold the AUDIO button
until TREB appears on the display. Press the knob above
the AUDIO button to extend it then turn the knob to
increase or decrease treble. When you use this knob, the
radio's tone setting will switch to manual. If a station is
weak or noisy, you may want to decrease the treble.
Pressing and holding the AUDIO button for at least
two seconds will return all tone settings, including
balance and fade to flat.
AUTO EQ: This button allows you to choose preset
bass, midrange and treble equalization settings designed
for country, jazz, pop, rock, classical and talk stations.The last setting will appear on the display when you first
press AUTO EQ. Each time you press AUTO EQ,
another setting will appear on the display. Press AUTO
EQ again after TALK appears and MANUAL will
appear. Tone control will return to manual operation
for bass, midrange and treble. Also, if you use bass,
midrange, or treble, the radio control will automatically
return to the manual mode. MANUAL will appear on
the display.
If your vehicle has the Bose radio, your audio system
allows you to choose from four different AUTO EQ
settings: talk, driver, normal and spatial. The AUTO EQ
settings can be used while listening to the radio, the
cassette tape player or CD player. Press the AUTO EQ
button to scroll through your choices. Select TALK
when listening to non
-musical material such as news,
talk shows, sports broadcasts and books on tape.
This setting makes spoken words sound very clear.
Select DRIVER to give the driver the best possible
sound qualities. Select NORMAL to enhance stereo
effect. Select SPATIAL to make the listening space
seem larger. When AUTO EQ NORMAL is displayed,
the system will provide the best overall Bose
performance. The radio keeps separate AUTO EQ
settings for each preset and source.

3-15
To use the P-TYPE interrupt feature, press and hold the
P
-TYPE button until you hear a beep on the PTY you
want to interrupt on. An asterisk will appear next to the
PTY name (for example CLASSICAL*). When you are
listening to a cassette or compact disc, the last selected
RDS FM station will interrupt play if that selected PTY
format is broadcast.
Setting PTY Preset Stations
The six numbered pushbuttons let you return to your
favorite Program Types (PTYs). These pushbuttons have
factory PTY presets. You can set up to 12 PTYs (six FM1
and six FM2), by performing the following steps:
1. Press P
-TYPE, if it is not already on.
2. Press AM FM to select FM1 or FM2.
3. Turn the SELECT knob to select a PTY.
4. Press and hold one of the six numbered pushbuttons
until you hear a beep. Whenever you press that
numbered pushbutton, the PTY you set will return.
5. Repeat the steps for each pushbutton.AM FM: The AM FM button operates the alternate
frequency feature. This feature allows the radio to
switch to a stronger station with the same program
type. Press and hold AM FM for two seconds to
turn alternate frequency on. AF ON will appear on
the display. The radio may switch to stronger stations.
Press and hold AM FM again for two seconds to turn
alternate frequency off. AF OFF will appear on the
display. The radio will not switch to other stations.
When you turn the ignition off and then on again,
the alternate frequency feature will automatically be
turned on.
Radio Announcements
(Alert): warns of national or local emergencies.
You will not be able to turn off alert announcements.
ALERT! appears on the display when an alert
announcement plays. When an alert announcement
comes on the tuned radio station, you will hear it,
even if the volume is muted or a cassette tape or
compact disc is playing. If the cassette tape or
compact disc player is playing, play will stop for the
announcement and resume when the announcement
is finished.

3-17
1 REV: Press this button to reverse the tape rapidly.
Press it again to return to playing speed. The radio will
play the last selected station while the tape reverses.
You may select stations during reverse operation by
using the TUNE RCL P
-TYPE control.
2 FWD: Press this button to advance quickly to
another part of the tape. Press the button again to
return to playing speed. The radio will play the last
selected station while the tape advances. You may select
stations during forward operation by using the TUNE
RCL P
-TYPE control.
3
: Press this button to reduce background noise.
DOLBY ON will appear on the display with the
Dolby icon. Press it again to turn Dolby off.
Dolby Noise Reduction is manufactured under a
license from Dolby Laboratories Licensing Corporation.
Dolby and the double
-D symbol are trademarks of
Dolby Laboratories Licensing Corporation.
5 SIDE: Press this button to play the other side
of the tape.AUTO EQ: Press AUTO EQ to select the desired
preset equalization setting while playing a cassette tape.
The equalization will be automatically set whenever you
play a cassette tape.

SEEK SCAN: To seek, press the right or left
pointing arrow briefly to search for the next or previous
selection on the tape. Your tape must have at least three
seconds of silence between each selection for seek to
work. You can skip nine selections forward or backward
on the tape. Choose how many selections you want to
skip. Press the right or left pointing arrows on the SEEK
SCAN button that many times. The number of selections
to be skipped will appear on the display.
To scan, press and hold the SEEK SCAN button for
more than two seconds until you hear a beep and
SCAN appears on the display. Use scan to listen to
each selection for a few seconds. The tape will go to the
next selection, stop for a few seconds, then go on to the
next selection. Press this button again to stop scanning.
AM FM: Press this button to play the radio when
a tape is in the player. The tape will stop but remain in
the player.