2002 OLDSMOBILE AURORA reset

2-84
To turn off messages on the DIC (except LOW OIL
PRESSURE, LOW BRAKE FLUID, PARK BRAKE
SET, STARTING DISABLED and the HOT...STOP
ENGINE warning), press the RESET button.
Pressing the SELECT right arrow button will allow you
to access the following modes, DATE/ET, FUEL,
ECON, OIL and GAGE. While in any of these modes,
warning messages can interrupt and take over the
display until you acknowledge the message, or the
condition causing the problem goes away.
English/Metric
The DIC can display information in either English or
metric. To change the display, press and hold the
ON/OFF button for about three seconds. This will also
change the digital screen for the climate control system
between English and metric.
Date/Elapsed Time
Pressing the SELECT down arrow while in DATE/ET
mode will allow you to choose between the date and the
elapsed time menus.Date
To set the date, press and hold the RESET button for
about three seconds while the date is being displayed on
the DIC. When the date set mode is entered the display
will show the following:
YEAR?_____ MM/DD/00
The year will be flashing. To increase the item that is
flashing press SELECT right arrow. To decrease the
item that is flashing press SELECT down arrow.
When you reach the current year press the RESET
button. The DIC will ask for the month. The month will
flash the same as the year. Use the SELECT buttons to
reach the current month and press RESET. The DIC will
then ask for the day. The day will flash the same as the
year. Use the SELECT buttons to reach the current day.
Press the RESET button again and the set display will
stop flashing and go back to the normal operation mode.
ProCarManuals.com

2-85
Elapsed Time (ET)
When the ignition is on, the DIC can be used as a
stopwatch. The display will show hours and minutes.
The elapsed time indicator will record up to 100 hours,
then it will reset to zero and continue counting. Press
SELECT down arrow while in the DATE/ET mode, and
the display will show the amount of time that has
elapsed since the elapsed time indicator was last reset
(not including time the ignition is off), such as:
01:08 ELAPSED TIME
To start or stop the counting of time, press the RESET
button briefly. If the colon (:) in the time is flashing,
time is being counted. Time is displayed in hours and
minutes. Seconds are not displayed. Time will continue
to be counted as long as the ignition is on, even if
another display is being shown on the DIC.
To reset elapsed time to zero, press the RESET button
for three seconds while the elapsed time is displayed.
Fuel
Press the SELECT down arrow while in the FUEL
mode to see how much fuel has been used and the
fuel range functions.Fuel Used
While in the FUEL USED function the display will
show a reading such as:
FUEL USED: 10.4 GAL or FUEL USED: 39.4 L
To learn how much fuel will be used from a specific
starting point, first enter the FUEL USED mode to
display FUEL USED, then press and hold the RESET
button for three seconds.
Don't confuse fuel used with the amount of fuel in
your tank.
Fuel Range
The FUEL RANGE mode calculates the remaining
distance you can drive without refueling. It's based on
fuel economy and the fuel remaining in the tank. The
display will show a reading such as:
FUEL RANGE: 235 MI or FUEL RANGE: 378 KM
If the range is less than 50 miles (80 km), the display
will read LOW FUEL RANGE.
The fuel economy data used to determine fuel range is
an average of recent driving conditions. As your driving
conditions change, this data is gradually updated. Fuel
range cannot be reset.
ProCarManuals.com

2-86 Fuel Economy
Pressing the SELECT down arrow while in the
ECON mode displays average fuel economy and
instantaneous fuel economy calculated for your
specific driving conditions.
Average fuel economy will be shown in a reading
such as:
25.2 AVG MI/GAL or 9.3 AVG L/100 KM
Instantaneous fuel economy will be shown in a reading
such as:
28 INST MI/GAL or 8.4 INST L/100 KM
The average fuel economy is viewed as a long
-term
approximation of your overall driving conditions.
If you press and hold RESET for three seconds in this
mode while you're driving, the system will begin
figuring average fuel economy from that point in time.
Instantaneous fuel economy cannot be reset.
Oil Life
The GM Oil Life System
is the only function
accessible in the OIL mode. Engine oil life is displayed
in a reading such as the following:
OIL LIFE 30%
This is an estimate of the oil's remaining useful life.
It will show 100% when the system is reset after an oil
change. It will alert you to change your oil on a schedule
consistent with your driving conditions.
When the remaining oil life is low, the system will alert
you with this message:
CHANGE OIL SOON
Always reset the OIL LIFE reminder after an oil change.
To reset the oil life system, see ªOil Life Systemº in
the Index. Also, see ªEngine Oil, When to Changeº in
the Index.
Remember, you must reset the OIL LIFE yourself after
each oil change. It will not reset itself. Also, be careful
not to reset the OIL LIFE accidentally at any time other
than when the oil has just been changed. It can't be reset
accurately until the next oil change.
ProCarManuals.com

2-87
The DIC does not replace the need to maintain your
vehicle as recommended in the Maintenance Schedule in
this manual. Also, the oil change reminder will not
detect dusty conditions or engine malfunctions that may
affect the oil. If you drive in dusty areas, change your oil
after every 3,000 miles (5 000 km) or three months,
whichever occurs first, unless the DIC instructs you to
do so sooner. Also, the oil change reminder does not
measure how much oil you have in your engine. So, be
sure to check your oil level often. See ªEngine Oilº in
the Index.
Gage
Pressing the SELECT down arrow while in GAGE
mode will allow you to access the battery volts, oil
pressure and tire pressure displays. Pressing and holding
the RESET button for three seconds while in average
speed and tire pressure displays will reset them. Pressing
the SELECT down arrow in GAGE mode will show the
following displays:

Battery voltage, such as the following:
VOLTS: 13.8

Oil pressure, such as the following:
OIL PRESSURE 40 PSI or OIL
PRESSURE 276 KPA
Average speed, such as the following:
AVG SPEED 55 MPH or AVG SPEED 90 KM/H

Tire pressure status, such as the following:
TIRE PRESSURE NORMAL or TIRE
PRESSURE LOW
TIRE PRESSURE NORMAL appears when the
check tire pressure system believes your vehicle's
tire pressures are normal. If a potential tire pressure
problem is detected, the display will show TIRE
PRESSURE LOW. If you see this message, you
should stop as soon as you can and check all four
tires for damage. If a tire is flat, see ªIf a Tire Goes
Flat º in the Index. Also check the tire pressure in all
four tires as soon as you can. See ªTire Pressureº in
the Index.
There are times when you will have to reset
(calibrate) the check tire pressure system. Pressing
the RESET button while the TIRE PRESSURE
LOW warning is displayed does not automatically
reset the tire pressure monitoring system. See
ªCheck Tire Pressure Systemº in the Index for
more information.
ProCarManuals.com

2-95 DIC Warnings and Messages
Other messages or warnings may appear in the DIC
display. For Canadian drivers, in addition to the DIC
message your DIC will display EXP with a number after
it which reflects the following messages:
EXP (Export ID) Warning Message. . . . . . . . . . . .
1 AIR BAG PROBLEM. . . . . . . . . . . . . . . . . . . . . .
3 CHANGE OIL SOON. . . . . . . . . . . . . . . . . . . . . .
4 CHECK CHARGE SYSTEM. . . . . . . . . . . . . . . . .
5 CHECK OIL LEVEL. . . . . . . . . . . . . . . . . . . . . . .
6 TRANS HOT...IDLE ENG. . . . . . . . . . . . . . . . . . .
7 CONFIRM TIME & DATE. . . . . . . . . . . . . . . . . .
8 DRIVERS DOOR AJAR. . . . . . . . . . . . . . . . . . . .
9 ENGINE HOT...A/C OFF. . . . . . . . . . . . . . . . . . .
10 HOT...REDUCE ENG RPM. . . . . . . . . . . . . . . . .
11 HOT...STOP ENGINE *. . . . . . . . . . . . . . . . . . . .
12 THEFT SYSTEM FAULT. . . . . . . . . . . . . . . . . .
13 LEFT REAR DOOR AJAR. . . . . . . . . . . . . . . . .
14 LOW BRAKE FLUID *. . . . . . . . . . . . . . . . . . . .
15 LOW ENGINE COOLANT. . . . . . . . . . . . . . . . .
16 LOW FUEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 LOW OIL PRESSURE *. . . . . . . . . . . . . . . . . . . 18 LOW TIRE PRESSURE. . . . . . . . . . . . . . . . . . .
19 LOW WASHER FLUID. . . . . . . . . . . . . . . . . . . .
20 PARK BRAKE SET *. . . . . . . . . . . . . . . . . . . . .
21 PASSENGER DOOR AJAR. . . . . . . . . . . . . . . .
22 RIGHT REAR DOOR AJAR. . . . . . . . . . . . . . . .
23 SERVICE VEHICLE SOON. . . . . . . . . . . . . . . .
24 TURN SIGNAL ON?. . . . . . . . . . . . . . . . . . . . . .
25 THEFT ATTEMPTED. . . . . . . . . . . . . . . . . . . . .
26 SERV STABILITY SYS. . . . . . . . . . . . . . . . . . . .
27 HEADLAMPS SUGGESTED. . . . . . . . . . . . . . .
28 TRUNK AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
29 BATTERY SAVER ACTIVE. . . . . . . . . . . . . . . .
32 HOT...IDLE ENGINE. . . . . . . . . . . . . . . . . . . . .
33 STARTING DISABLED *. . . . . . . . . . . . . . . . . .
36 CHECK GAS CAP. . . . . . . . . . . . . . . . . . . . . . . .
42 STABILITY ACTIVE. . . . . . . . . . . . . . . . . . . . .
The EXP codes are used to make translation from
English to other languages easier.
Pressing the RESET button will remove the above
messages or warnings from the DIC display, unless
noted by an asterisk (*).
ProCarManuals.com

2-96
CHECK OIL LEVEL - 5: If you ever see the
CHECK OIL LEVEL message, it indicates that the
engine oil level is 1 to 1 1/2 quarts (0.9 L to 1.4 L) low.
The message will appear only if the engine is running
and it has been at least eight minutes since the engine
was last running. If the message appears, check the oil
dipstick level. If it reads low, your oil level should be
brought up to the proper level (see ªEngine Oilº in the
Index). After bringing the oil to the proper level, the
ignition must be off for eight minutes to allow the
majority of oil to drain into the oil pan.
SERV STABILITY SYS
- 26: If you ever see the
SERV STABILITY SYS message, it means there may
be a problem with your stability enhancement system. If
you see this message, try to reset the system (stop; turn
off the engine; then start the engine again). If the SERV
STABILITY SYS message still comes on, it means there
is a problem. You should see your dealer for service.
Reduce your speed and drive accordingly.STABILITY ACTIVE
- 42: You may see the
STABILITY ACTIVE message on the Driver
Information Center. It means that an advanced,
computer
-controlled system has come on to help your
vehicle continue to go in the direction in which you're
steering. This stability enhancement system activates
when the computer senses that your vehicle is just
starting to spin, as it might if you hit a patch of ice or
other slippery spot on the road. When the system is on,
you may hear a noise or feel a vibration in the brake
pedal. This is normal.
When the STABILITY ACTIVE message is on, you
should continue to steer in the direction you want to go.
The system is designed to help you in bad weather or
other difficult driving situations by making the most of
whatever road conditions will permit. If the STABILITY
ACTIVE message comes on, you'll know that
something has caused your vehicle to start to spin, so
you should consider slowing down.
ProCarManuals.com

3-12
To scan preset stations, press and hold either SCAN
arrow for more than four seconds, PRESET SCAN will
appear on the display. You will hear a double beep and
the P will blink with the preset number. The radio will
go to the first preset station stored on your pushbuttons,
play for a few seconds, then go on to the next preset
station. Press either SCAN arrow again to stop scanning
presets. The radio will scan preset stations with a strong
signal only. The sound will mute while scanning.
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations (six AM,
six FM1 and six FM2), by performing the following steps:
1. Turn the radio on.
2. Press BAND to select the band.
3. Tune in the desired station.
4. Press AUTO EQ to select the equalization that best
suits the type of station selected.
5. Press and hold one of the six numbered pushbuttons
until you hear a beep. Whenever you press that
numbered pushbutton, the station you set will return
and the equalization that you selected will also be
automatically selected for that pushbutton.
6. Repeat the steps for each pushbutton.Setting the Tone (Bass/Treble)
AUDIO: Press the AUDIO button until BASS, MID
or TREB appears on the display. Press the knob above
the AUDIO button to extend it, then turn the knob to
increase or decrease. When you use this knob, the
radio's tone setting will switch to manual. If a station is
weak or noisy, you may want to decrease the treble.
Press and hold the AUDIO button for at least two
seconds to return all tone settings, including balance
and fade to flat.
AUTO EQ (Automatic Equalizer): This feature
allows you to choose preset bass, midrange and treble
equalization settings designed for country, jazz, talk,
pop, rock and classical program types.
The program type last chosen will appear on the display
when you first press AUTO EQ. Each time you press
this button, another program type will appear on the
display and AUTO EQ will switch to one of the preset
program types.
To return to the manual mode, press the AUTO EQ
button until MANUAL appears on the display. Then you
will be able to manually adjust the bass, midrange and
treble using the AUDIO button.
ProCarManuals.com

3-13
If your vehicle has the Bose radio, the AUTO EQ button
will work the same, except the radio will display EQ1
through EQ6 as the choices instead of displaying the
equalization setting names. These settings can be used
while listening to the radio or the CD player.
The radio saves separate AUTO EQ settings for each
preset and source.
Adjusting the Speakers (Balance/Fade)
AUDIO: To adjust the balance between the right
and left speakers, press the AUDIO button until BAL
appears on the display. Press the knob above the AUDIO
button to extend it, then turn the knob to adjust the
sound to the left or right speakers. The middle position
balances the sound between the speakers.
To adjust the fade between the front and rear speakers,
press the AUDIO button until FAD appears on the
display. Press the knob above the AUDIO button to
extend it, then turn the knob to adjust the sound to the
front or rear speakers. The middle position balances the
sound between the speakers.
Press and hold the AUDIO button for at least two
seconds to return all tone settings, including bass
and treble to flat.Using RDS
Your audio system is equipped with a Radio Data
System (RDS). With RDS, the radio can do
the following:

Seek only to stations with the types of programs you
want to listen to,

seek to stations with traffic announcements,

receive announcements concerning local and
national emergencies, and

receive and display messages from radio stations.
RDS features are only available on FM stations that
broadcast RDS information. The RDS features on your
radio rely on receiving specific RDS information from
these stations. These features will only work when the
RDS information is available. In rare cases, a radio
station may broadcast incorrect information that will
cause the radio features to work improperly. If this
happens, contact the radio station.
When you are tuned to an RDS station, the station
name will appear on the display, instead of the
frequency. Most RDS stations provide their station
name, the time of day and a Program Type (PTY)
for their current programming.
ProCarManuals.com