2002 MAZDA MODEL PROTÉGÉ oil dipstick

8-10
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
Engine Compartment Overview
Automatic transaxle fluid-level dipstick (only for automatic transaxle)
Brake/Clutch fluid reservoir
Battery
Fuse block
Engine coolant reservoir
Air filter
Cooling system cap Engine oil dipstick Engine oil filter 1.6-liter engine
1.8 and 2.0-liter enginesEngine oil-filler cap
Power steering
fluid reservoir
Windshield washer
fluid reservoir
Automatic transaxle fluid-level dipstick (only for automatic transaxle)
Brake/Clutch fluid reservoir
Battery
Fuse block
Engine coolant reservoir
Air filter Cooling system cap Engine oil filter Engine oil-filler cap
Engine oil dipstick
Power steering
fluid reservoir
Windshield washer
fluid reservoir
J39L(02MY).book Page 10 Thursday, November 1, 2001 10:49 AM

8-11
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F

Recommended Oil
Oil container labels provide important
information.
The quality designation SG, SH, SJ, SL,
or ILSAC
must be on the label.
Engine oil viscosity, or thickness, has an
effect on fuel economy and cold-weather
operation (starting and oil flow).
Low-viscosity engine oils can provide
improved fuel economy and cold-weather
performance.
But high-temperature weather conditions
require higher-viscosity engine oils for
satisfactory lubrication.When choosing an oil, consider the
temperature range your vehicle will
operate in before the next oil change.
Then select the recommended viscosity
from this chart.
Energy conserving oils are recommended.
A chief contribution they make to fuel
economy is reducing the amount of fuel
necessary to overcome engine friction.

Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait 5 minutes for the
oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
Engine Oil
SAEFORGASOLINEENGINES10W-30
(ILSAC)
–30–20–100 1020304050
–20 0 20 40 60 80 100 120
5W-30
10W-30
Using oils of viscosity besides those
recommended for specific temperature
ranges could result in engine damage.
CAUTION
Full 1.6-liter engine
Low OK
J39L(02MY).book Page 11 Thursday, November 1, 2001 10:49 AM

8-12
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
5. Pull it out again and examine the level.
It’s OK between L and F.
But if it’s near at or below L, add
enough oil to bring the level to F.
6. Make sure the O-ring is positioned
properly before reinserting the
dipstick.
The distance between L and F on the
dipstick represents the following:

Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
Changing engine oil
Don’t add engine oil over F. This may
cause engine damage.
L (US qt, Imp qt) 1.0 (1.05, 0.87)
Full 1.8 and 2.0-liter engines
Low OK
CAUTION
Handling Used Engine Oil:
Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
Checking or Changing Engine Oil:
Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don’t check or
change the engine oil when the
engine is hot.
WARNING
WARNING
1.6-liter engine
Loosen Tighten
Front
Drain
plug
J39L(02MY).book Page 12 Thursday, November 1, 2001 10:49 AM

8-13
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
1. Warm up the engine for a few minutes
and turn it off. Remove the oil-filler
cap.
2. Remove the drain plug and drain the oil
into a suitable container.
3. Replace the plug tightly after the oil
has thoroughly drained.
4. Fill the engine with new oil to the F
mark on the dipstick.
5. Securely replace the oil-filler cap.
6. Start the engine and inspect around the
drain plug for leaks.
7. Turn it off and wait 5 minutes for the
oil to return to the oil pan.
Check the oil level and fill to the F mark if
necessary.
Oil capacity (General reference only,
refer to Specifications section for
capacities.)Changing oil filterBecause you need a special tool to
retighten the filter, an Authorized Mazda
Dealer should do the work.
1.8 and 2.0-liter engines
Loosen
Tighten
Front
Drain
plugNOTE
•The indicated engine oil capacities
are for general reference purposes
only. When adding or changing oil,
verify the engine oil level with the
oil dipstick.
•Use only specified engine oil (page
10-4).
J39L(02MY).book Page 13 Thursday, November 1, 2001 10:49 AM

10-5
Specifications
Form No. 8Q36-EA-01F

Capacities
(Approximate Quantities)
Check oil and fluid levels with dipsticks or reservoir gauges.

Dimensions
ItemUnit
L US qt Imp qt
Engine oil1.6-liter engineWith oil filter replacement 3.2 3.4 2.8
Without oil filter
replacement3.0 3.2 2.6
1.8 and 2.0-liter
enginesWith oil filter replacement 3.5 3.7 3.1
Without oil filter
replacement3.3 3.5 2.9
Coolant1.6-liter engineWith heater 6.0 6.3 5.3
Without heater 5.5 5.8 4.8
1.8 and 2.0-liter
enginesWith heater 7.5 7.9 6.6
Without heater 6.9 7.3 6.1
Transaxle oilManual transaxle 2.7 2.9 2.4
Automatic transaxle 7.2 7.6 6.3
Fuel tank1.6-liter engine 50 13.2 (US gal) 11.0 (Imp gal)
1.8 and 2.0-liter engines 55 14.5 (US gal) 12.1 (Imp gal)
ItemModel
Sedan Hatchback
Overall length 4,450 mm (175.2 in) 4,331 mm (170.5 in)
Overall width 1,705 mm (67.1 in) 1,705 mm (67.1 in)
Overall height 1,410 mm (55.5 in) 1,410 mm (55.5 in)
Front tread 1,470 mm (57.9 in) 1,465 mm (57.7 in)
Rear tread 1,470 mm (57.9 in) 1,470 mm (57.9 in)
Wheelbase 2,610 mm (102.8 in) 2,610 mm (102.8 in)
J39L(02MY).book Page 5 Thursday, November 1, 2001 10:49 AM