2002 MAZDA MODEL PROTÉGÉ ignition

6-20
Interior Comfort
Au di o S ys t em
Form No. 8Q36-EA-01F

Clock
Setting the time
The clock can be set at any time when the
ignition switch is in the ACC or ON
position.
1. To adjust the time, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock’s current time will flash.
2. To advance the hours, press the hour
set button ( ). To advance the minutes,
press the minute set button ( ) while
the time is flashing.
3. Press the clock button ( ) again
to start the clock.Exact hour adjustment 1. To set the exact hour, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock’s current time will flash.
2. Press the clock button ( ) again
and the time will be adjusted as
follows:
(Example)
12:01—12:29
→12:00
12:30—12:59
→1:00
Display Clock button
Hour set
button
Minute set
button
NOTE
If the power supply to the unit is
interrupted (if the fuse blows or the
vehicle’s battery is disconnected), the
clock will need to be reset.
J39L(02MY).book Page 20 Thursday, November 1, 2001 10:49 AM

6-25
Interior Comfort
Au di o S ys t em
Form No. 8Q36-EA-01F
Dolby and the double-D symbol are
trademarks of Dolby Laboratories
Licensing Corporation.
Ejecting the cassette tape
Press the cassette tape eject button ( ) to
eject the cassette tape.
Fast forward/Rewind
Press the fast-forward button ( ) to
fast-forward.
Press the rewind button ( ) to rewind.
To stop this operation and play the
cassette tape, press the button again.
Reversing
Press the program button ( ) to
change cassette tape-playing direction.
Automatic program control (APC)
APC is used to find the beginning of
either the next program or the one being
played.Press the APC button ( ) to the
beginning of the next selection.
Press the APC button ( ) to the
beginning of the one being played. To
stop this operation and play the cassette
tape, press the button again.
If APC detects 15 seconds of blank space
it will automatically advance the tape to
the next selection.
Repeat play
This operation makes it possible to listen
to a selection repeatedly.
Press the repeat button ( ) during play.
The current selection playing will be
repeated ("RPT" will be displayed).
Press the repeat button ( ) once again
to cancel repeat play.
NOTE
The cassette tape can be ejected when
the ignition switch is in the OFF
position.
NOTE
When the cassette tape ends during
fast forward or rewind, it automatically
stops and starts playing.
NOTE
When the cassette tape ends, the unit
automatically reverses play.
NOTE
APC may not operate properly if
•A tape was recorded at a low level.
•A tape has long, silent intervals.
•A tape is a live recording.
•A tape has very short intervals of
less than 3 seconds.
NOTE
RPT may not operate properly if
•A tape was recorded at a low level.
•A tape has long, silent intervals.
•A tape is a live recording.
•A tape has very short intervals of
less than 3 seconds.
J39L(02MY).book Page 25 Thursday, November 1, 2001 10:49 AM

6-31
Interior Comfort
Au di o S ys t em
Form No. 8Q36-EA-01F
Multiple insertion
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. When "In" is displayed, insert the CD.
3. When "In" is displayed again, insert
the next CD.
Ejecting the CD
Normal ejection
1. Press the CD eject button ( ). The
disc number and "OUT" will be
displayed.
2. Pull out the CD.
Ejecting CDs from desired tray number
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the
desired CD number within 5 seconds
after the beep is heard.
3. Pull out the CD.Multiple ejection
1. Press and hold the CD eject button ( )
for about 2 seconds until a beep is
heard.
2. Wait 5 seconds or press the CD eject
button ( ) again within 5 seconds
after the beep is heard.
3. Pull out the CD, then the next CD will
be ejected.
Playing
Press the CD play button ( ) to start
playing when a CD is in the unit.
Fast-forward/Reverse
Press and hold the fast-forward button
( ) to advance through a track at high
speed.
Press and hold the reverse button ( )
to reverse through a track at high speed.
Tr a c k s e a r c h
Press the track up button ( ) once to
skip forward to the beginning of the next
track.
Press the track down button ( ) once to
skip back to the beginning of the current
track.
NOTE
The first-inserted CD will be played
automatically when:
•No CD is inserted within 15
seconds after "In" is displayed.
•The CD trays are full.
NOTE
When the CD is ejected during play,
the next CD will be played
automatically.
NOTE
•CDs will be ejected starting with the
one with the lowest number.
•All CDs in the tray will be ejected
continuously.
•CDs can be ejected when the
ignition switch is off. Press and hold
the CD eject button ( ) for about 2
seconds and all CDs will eject.
J39L(02MY).book Page 31 Thursday, November 1, 2001 10:49 AM

6-35
Interior Comfort
Form No. 8Q36-EA-01F
Interior Equipment
When you need a sunvisor, lower it for use
in front or swing it to the side.

Va n i t y M i r r o r s
To use the vanity mirror, lower the
sunvisor.

Illuminated Entry System
When the switch is in the DOOR position,
the interior light comes on for:
•about 30 seconds after the driver’s door
is unlocked and the ignition key is
removed.
•about 15 seconds after all doors are
closed.
•about 15 seconds after the key is
removed from the ignition.
The light also goes out when:
•the ignition switch is turned to the ON
position and all doors are closed.
•the driver’s door is locked.
Sunvisors
Sunvisor
Interior Lights
NOTE
If any door is left opened, the light
goes out after about 5 minutes.
J39L(02MY).book Page 35 Thursday, November 1, 2001 10:49 AM

6-37
Interior Comfort
Interior Equipment
Form No. 8Q36-EA-01F

Luggage Compartment Light
The ignition switch must be in the ACC or
ON position.
Press it in and release it. When ready for
use, it automatically pops out.
OFF Light off
ON Light on when the liftgate is open
OFF
ON
Lighter
•Don’t touch the metal part of the
lighter, you may burn yourself.
•Don’t hold the lighter in because it
will overheat.
•Don’t use the lighter socket for
plug-in accessories such as shavers
and coffee pots. They may damage
it or cause electrical failure. Use
only a genuine Mazda lighter or the
equivalent.
•If the lighter doesn’t pop out within
30 seconds, remove it to prevent
overheating.
CAUTION
J39L(02MY).book Page 37 Thursday, November 1, 2001 10:49 AM

7-13
In Case of an Emergency
Form No. 8Q36-EA-01F
Overheating
If the temperature gauge indicates
overheating, you experience power loss,
or you hear a loud knocking or pinging
noise, the engine is probably too hot.
If this happens:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic
transaxle in park (P), a manual
transaxle in neutral.
Apply the parking brake.
3. Turn off the air conditioner.4. Check whether coolant or steam is
escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:
Don’t go near the front of the vehicle.
Stop the engine. Then turn the ignition
switch to the ON position without
starting the engine.
The radiator cooling fans will start to
cool the engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools. If this doesn’t lower the
temperature, stop the engine and let it
cool.
5. Check the coolant level.
If it’s low, look for leaks in the radiator
hoses and connections, heater hoses
and connections, radiator, and water
pump.
If you find a leak or other damage, or if
coolant is still leaking, stop the engine
and call an Authorized Mazda Dealer.
If you find no problems, the engine is
cool, and no leaks are obvious, carefully
add coolant as required (page 8-14).
Overheating
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
WARNING
Cooling system cap
Engine coolant
reservoir
J39L(02MY).book Page 13 Thursday, November 1, 2001 10:49 AM

7-15
In Case of an Emergency
Form No. 8Q36-EA-01F
Emergency Starting
If the engine fails to start, it may be
flooded (excessive fuel in the engine).
Follow this procedure:
1. Depress the accelerator all the way and
hold it there.
2. Turn the ignition switch to the START
position and hold it there—for up to 10
seconds. If the engine starts, release the
key and accelerator immediately
because the engine will suddenly rev
up.
3. If the engine fails to start, crank it
without using the accelerator—for up
to 10 seconds.Jump-starting is dangerous if done
incorrectly. So follow the procedure
carefully. If you feel unsure about jump-
starting, we strongly recommend that you
have a competent service technician do
the work.
Starting a Flooded EngineJump-Starting
Battery-Related Explosion:
Flames and sparks near open battery
cells are dangerous. Hydrogen gas,
produced during normal battery
operation, could ignite and cause the
battery to explode. An exploding
battery can cause serious burns and
injuries. Keep all flames, including
cigarettes, and sparks away from
open battery cells.
Low Fluid Level or Frozen Battery:
Jump-starting a frozen battery or one
with a low fluid level is dangerous. It
may rupture or explode, causing
serious injury.
Don’t jump-start a frozen battery or
one with a low fluid level.
Use only a 12 V booster system. You
can damage a 12 V starter, ignition
system, and other electrical parts
beyond repair with a 24 V power
supply (two 12 V batteries in series or
a 24 V motor generator set).
WARNING
CAUTION
J39L(02MY).book Page 15 Thursday, November 1, 2001 10:49 AM

8-6
Maintenance and Care
Scheduled Maintenance
Form No. 8Q36-EA-01F
Emission control and related systems
The ignition and fuel systems are highly important to the emission control system and to
efficient engine operation. Don’t tamper with them.
All inspections and adjustments must be made by a qualified technician. We strongly
recommend that all servicing related to these systems be done by an Authorized Mazda
Dealer.
I
: Inspect: Inspect and clean, repair, adjust, or replace if necessary . R: Replace
*1: Also inspect and adjust the power steering and air conditioner drive belts, if installed.
*2: Replacement of the timing belt is required at every 100,000 km (60,000 miles). Failure to replace the timing
belt may result in damage to the engine.
*3: If the vehicle is operated under any of the following conditions, change the engine oil and oil filter more often
than recommended intervals.
a) Driving in dusty conditions.
b) Extended periods of idling or low speed operation.
c) Driving for long period in cold temperatures or driving regularly at short distance only.
*4: If the vehicle is operated in very dusty or sandy areas, inspect and if necessary, clean or replace the air filter
more often than the recommended intervals.
Scheduled Maintenance (Chile)
NOTE
•After the described period, continue to follow the described maintenance at the
recommended intervals.
•As the result of visual examination or functional measurement of a system’s
operation (performance), correct, clean, or replace as required. (Inspect, and if
necessary replace the air filter)
Maintenance
Interval
Maintenance
ItemNumber of months or km (miles), whichever comes first
Months 6 121824303642485460667278849096
×1000 Km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
(×1000 Miles) (6) (12) (18) (24) (30) (36) (42) (48) (54) (60) (66) (72) (78) (84) (90) (96)
Engine valve clearance
Ins
pect every 100,000 km (60,000 miles) or 60 months
Idle speedIIIIIIII
Fuel filterRRRR
Spark plugsRRRRR
Evaporative system (if installed)
IIIIIIII
Drive belts*
1IIIIIIIIIIIIIIII
Engine timing belt*2Replace every 100,000 km (60,000 miles)
Engine oil*3RRRRRRRRRRRRRRRR
Oil filter*3RRRRRRRRRRRRRRRR
Cooling systemIIIIIIII
Engine coolant
Re
place every 2 years
Air filter*4IRIRIRIR
Fuel line and hosesIIIIIIII
J39L(02MY).book Page 6 Thursday, November 1, 2001 10:49 AM