2002 MAZDA MODEL MPV tow

5-8
Driving Your Mazda
Starting and Driving
Form No. 8Q44-EA-01K

Brake Pad Wear Indicator
When the disc brake pads become worn,
the built-in wear indicators contact the
disc plates. This causes a screeching noise
to warn that the pads should be replaced.
When you hear this noise, consult an
Authorized Mazda Dealer as soon as
possible.Various Lockouts:
NOTE
When the engine is jump-started to
charge the battery, uneven rpm occurs
and the ABS warning light comes on.
This is due to a weak battery, not a
malfunction.
Recharge the battery.
Driving with Worn Disc Pads:
Driving with worn disc pads is
dangerous. The brakes could fail and
cause a serious accident. As soon as
you hear a screeching noise consult
an Authorized Mazda Dealer.
WARNING
Automatic Transaxle
Controls
Indicates that you must depress the
brake pedal and pull the shift lever
toward you to shift (The ignition
switch must be in the ON position).
Indicates the shift lever can be shifted
freely into any position.
Indicates that you must pull the shift
lever toward you to shift.
Overdrive button
For gear selection
with either a four-
speed or five-speed
transaxle
J16L_EA.book Page 8 Friday, February 22, 2002 11:34 AM

5-16
Driving Your Mazda
Starting and Driving
Form No. 8Q44-EA-01K

To Cancel
To turn off the system, use one
of these
methods:
•Press the CRUISE MAIN switch.
•Slightly depress the brake pedal.
•Pull the lever toward you.
The system is off when the ignition is off.The Traction Control System (TCS)
enhances traction and safety by regulating
engine torque. When the TCS detects
driving wheel slippage, it lowers engine
torque to prevent loss of traction.
This means that on a slick surface, the
engine adjusts automatically to provide
optimum power to the drive wheels
without causing them to spin and lose
traction.
NOTE
Cruise control will cancel at about 15
km/h (9 mph) below the preset speed
or below 40 km/h (25 mph).
Traction Control System
(TCS)
TCS and Unsafe Driving:
The traction control system (TCS)
cannot compensate for unsafe and
reckless driving, excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning
(reduced tire friction and road
contact because of water on the road
surface). You can still have an
accident. So don’t rely on the traction
control system as a substitute for safe
driving.
TCS and Snow and Ice:
Driving without proper traction
devices on snow and ice-covered
roads is dangerous. The traction
control system (TCS) alone cannot
provide adequate traction and you
could still have an accident. Use snow
tires or tire chains and drive at
reduced speeds when roads are
covered with ice and snow.
WARNING
J16L_EA.book Page 16 Friday, February 22, 2002 11:34 AM

5-21
Driving Your Mazda
Instrument Cluster and Indicators
Form No. 8Q44-EA-01K
The trip meter records the total distance
the vehicle is driven until the meter is
again reset. Return it to "0.0" by holding
the selector depressed for more than 1
second. Use this meter to measure trip
distances and in to compute fuel
consumption.

Tachometer
The tachometer shows engine speed in
thousands of revolutions per minute
(rpm).

Engine Coolant Temperature
Gauge
The engine coolant temperature gauge
shows the temperature of the engine
coolant.
If the needle exceeds normal range toward
H, it indicates overheating.
NOTE
•Only the trip meters record tenths of
kilometers (miles).
•The trip record will be erased when
the vehicle is driven over 999.9 km
(mile).
Don’t run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine damage.
Red zone
CAUTION
Driving with an overheated engine can
cause serious engine damage
(page 7-15).
CAUTION
J16L_EA.book Page 21 Friday, February 22, 2002 11:34 AM

5-25
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q44-EA-01K

Brake System Warning Light
This warning has the following functions:
Parking brake warning
The light comes on when the parking
brake is applied with the ignition switch
in the START or ON position. It goes off
when the parking brake is fully released.
Low brake fluid level warning/
Electronic brake force distribution
system warning
If the light stays on after the parking brake
is fully released, you may have a brake
problem.
Drive to the side of the road and park off
the right-of-way.
Low brake fluid level warning
You may notice that the pedal is harder to
push or that it may go closer to the floor.
In either case, it will take longer to stop
the vehicle.
1. With the engine stopped, check the
brake fluid level immediately and add
fluid as required (page 8-13).
2. After adding fluid, check the light
again.If the warning light remains on, or if the
brakes do not operate properly, do not
drive the vehicle. Have it towed to an
Authorized Mazda Dealer.
Even if the light goes off, have your brake
system inspected as soon as possible.
Electronic brake force distribution
system warning
If the electronic brake force distribution
control unit determines that some
components are operating incorrectly, the
control unit may turn the brake system
warning light on.
In this case, the ABS warning light comes
on at the same time (page 5-27).
J16L_EA.book Page 25 Friday, February 22, 2002 11:34 AM

5-27
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q44-EA-01K
2. Turn off the engine and inspect the
engine oil level (page 8-9). If it’s low,
add oil.
3. Check the light.
If the light remains on even after you add
oil, have your vehicle towed to the nearest
service station or to an Authorized Mazda
Dealer.

Check Engine Light
If this light comes on while driving, the
vehicle may have a problem. It is
important to note the driving conditions
when the light came on and consult an
Authorized Mazda Dealer.
The check engine light may come on in
the following cases:
•The fuel tank level being very low or
approaching empty.
•The engine’s electrical system has a
problem.
•The emission control system has a
problem.
•The fuel-filler cap is missing or not
tightened securely.If the check engine light flashes
continuously, decrease your speed and
consult an Authorized Mazda Dealer as
soon as possible.

ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible. Don’t run the engine if oil pressure is
low. It could result in extensive engine
damage.
CAUTION
ABS Warning Light and Brake
Warning Light on at the Same Time:
Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
J16L_EA.book Page 27 Friday, February 22, 2002 11:34 AM

5-32
Driving Your Mazda
Form No. 8Q44-EA-01K
Switches and Controls

Headlights
To turn on the lights, turn the knob on the
end of the control lever.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.

Headlight High-Low Beam
Push the lever forward for high beams.
Pull it back for low.

Flashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch need
not be on, and the lever will return to the
normal position when released.
Lighting Control
Lever Position OFF
Headlights Off Off On
Taillights
Parking lights
License lights
Side-marker lightsOff On On
NOTE
To prevent discharging the battery,
don’t leave the lights on while the
engine is off.
High beams
Low beams
J16L_EA.book Page 32 Friday, February 22, 2002 11:34 AM

5-33
Driving Your Mazda
Switches and Controls
Form No. 8Q44-EA-01K

Daytime Running Lights
(Canada Model)
In Canada, vehicles must be driven with
the headlights on during daytime
operation.
For that reason, the daytime running lights
automatically turn on when the ignition
switch is turned to the ON position.

Tu r n S i g n a l
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Green indicators on the dashboard show
which signal is working.
Lane-change signals
Move the lever slightly toward the
direction of the change—until the
indicator flashes—and hold it there. It
will return to the off position when
released.
NOTE
The running lights go off when the
parking brake is applied.
Turn and Lane-Change
Signals
NOTE
If an indicator light stays on without
flashing or if it flashes abnormally, the
turn signal bulb may be burned out.
Right turn
Left turn Right lane
change
Left lane
changeOFF
J16L_EA.book Page 33 Friday, February 22, 2002 11:34 AM

5-35
Driving Your Mazda
Switches and Controls
Form No. 8Q44-EA-01K

Windshield Wipers
Turn the wipers on by pulling the lever
down.
INT
— Intermittent
1
— Normal
2
— Fast
Variable-speed intermittent wipers
Set the lever to INT and choose the
interval timing by rotating the ring.One-touch wipers
For a single wiping cycle, push the lever
up to MIST.

Windshield Washer
Pull the lever toward you and hold it to
spray washer fluid.
If the washer doesn’t work, inspect the
fluid level (page 8-16). If it’s OK, consult
an Authorized Mazda Dealer.
OFF
INT
1
2
OFF
INT
INT ring
NOTE
In the OFF or INT position, the wipers
will be activated until the lever is
released.
OFF MIST
J16L_EA.book Page 35 Friday, February 22, 2002 11:34 AM