2002 MAZDA MODEL MPV air condition

6-7
Interior Comfort
Climate Control System
Form No. 8Q44-EA-01K
Recirculated air position ( )
Outside air is shut off. Air within the
vehicle is recirculated.
This position can be used when driving on
a dusty road or in similar conditions. It
also helps to provide quicker cooling of
the interior.

Heating
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.5. If dehumidified heating is desired, turn
on the air conditioner.

Cooling (With Air Conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
desired position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner.
The Recirculated Air Position:
Using the position in cold
weather will cause the glass to fog up.
Your vision will be hampered, which
could lead to a serious accident. Do
not use the position in cold
weather.
WARNING
NOTE
•If the windshield fogs up easily, set
the mode selector dial to the
position.
•If cooler air is desired at face level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
•The air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
J16L_EA.book Page 7 Friday, February 22, 2002 11:34 AM

6-8
Interior Comfort
Climate Control System
Form No. 8Q44-EA-01K
5. Adjust the fan control dial and
temperature control dial to maintain
maximum comfort.
Ve n t i l a t i o n
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.

Windshield Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
desired position. When using the air conditioner while
driving up long hills or in heavy traffic,
closely monitor the temperature gauge
(page 5-21).
The air conditioner may cause engine
overheating. If the gauge indicates
overheating, turn the air conditioner
off.
NOTE
•When maximum cooling is desired,
set the temperature control dial to
the extreme cold position and set
the air intake selector to the
position, then set the fan control dial
to the position 4.
•If warmer air is desired at floor
level, set the mode selector dial at
the position and adjust the
temperature control dial to maintain
maximum comfort.
•The air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
CAUTION
J16L_EA.book Page 8 Friday, February 22, 2002 11:34 AM

6-9
Interior Comfort
Climate Control System
Form No. 8Q44-EA-01K
3. Set the fan control dial to the desired
speed.
Dehumidifying (With Air
Conditioner)
Operate the air conditioner in cool or cold
weather to help defog the windshield and
side windows.
1. Set the mode selector dial to the
desired position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
5. Turn on the air conditioner.
Foggy Windshield:
Using the position with the
temperature control set to the cold
position will cause the outside of the
glass to fog up. Your vision will be
hampered, which could lead to a
serious accident. Set the temperature
control to the hot or warm position
when using the position.
NOTE
•For maximum defrosting, set the
temperature control dial to the
extreme hot position and the fan
control dial to position 4.
•If warm air is desired at the floor,
set the mode selector dial to the
position.
•In the or position, outside air
is automatically selected.The air
intake selector switch cannot be
changed to the position.
WARNING
J16L_EA.book Page 9 Friday, February 22, 2002 11:34 AM

6-10
Interior Comfort
Climate Control System
Form No. 8Q44-EA-01K

Adjusting the Vents
Directing airflow
You can direct air flow by moving the adjustment knob.
Vent Operation (Rear)
NOTE
When using the air conditioner, mist may come out from the vents. This is not a sign of
trouble but a result of humid air being suddenly cooled.
Knob
J16L_EA.book Page 10 Friday, February 22, 2002 11:34 AM

6-12
Interior Comfort
Climate Control System
Form No. 8Q44-EA-01K

Control Switches
Rear air-conditioner main switch
The air conditioner has front and rear
controls. The front air-conditioner
controls override the rear controls.
The rear air-conditioner main switch is
under the front air-conditioner control
panel.This switch allows variable fan speeds for
the rear air-conditioner.
0
—Fan off
REAR
—Select the desired fan speed
with rear air-conditioner
control panel.
1
—Low speed
2
—Medium speed
3
—High speed
Control Panel (Rear)
021
3
021
3
Fan control dial
Fan control dial Temperature control dial Mode selector dial
Type A
NOTE:
(Rear heater type)
(Rear cooler type)
Type BSupplies only hot air
out of floor outlets.
NOTE:
Supplies cold or hot
air out of roof vents
and/or floor outlets. Supplies only cold air
out of roof vents.
0123REAR
J16L_EA.book Page 12 Friday, February 22, 2002 11:34 AM

6-13
Interior Comfort
Climate Control System
Form No. 8Q44-EA-01K
Fan control dial
This dial allows variable fan speeds.
0
—Fan off
1
—Low speed
2
—Medium speed
3
—High speed
Temperature control dial (Type B)
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.Mode selector dial (Type B)
Turn the mode selector dial to select
airflow mode (page 6-11).
NOTE
When the rear air-conditioner main
switch is not set to the REAR position,
the fan control dial of the rear air-
conditioner control panel does not
work.
The front air-conditioner controls
override the rear controls.
021
3
Hot Cold
J16L_EA.book Page 13 Friday, February 22, 2002 11:34 AM

6-40
Interior Comfort
Au di o S ys t em
Form No. 8Q44-EA-01K
This CD player is made and tested to meet exacting safety standards. It meets FCC
requirements and complies with safety performance standards of the U.S. Department of
Health and Human Services.
Safety Certification
•This CD player should not be adjusted or repaired by anyone except qualified service
personnel.
If servicing is required, contact an Authorized Mazda Dealer.
•Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous laser exposure. Never operate the CD player
with the top case of the unit removed.
•Changes or modifications not expressly approved by Mazda may void the user’s
authority to operate this equipment.
NOTE
For CD player section:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1)This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
CAUTION
J16L_EA.book Page 40 Friday, February 22, 2002 11:34 AM

7-15
In Case of an Emergency
Form No. 8Q44-EA-01K
Overheating
If the temperature gauge indicates
overheating, you experience power loss,
or you hear a loud knocking or pinging
noise, the engine is probably too hot.
If this happens:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Shift into park (P).
Apply the parking brake.
3. Turn off the air conditioner.4. Check whether coolant or steam is
escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:
Don’t go near the front of the vehicle.
Stop the engine. Then turn the ignition
switch to the ON position without
starting the engine.
The radiator cooling fans will start to
cool the engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools. If this doesn’t lower the
temperature, stop the engine and let it
cool.
5. Check the coolant level.
If it’s low, look for leaks in the radiator
hoses and connections, heater hoses
and connections, radiator, and water
pump.
If you find a leak or other damage, or if
coolant is still leaking, stop the engine
and call an Authorized Mazda Dealer.
If you find no problems, the engine is
cool, and no leaks are obvious, carefully
add coolant as required (page 8-11).
Overheating
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
WARNING
F
L
Cooling
system cap
Coolant reservoir
J16L_EA.book Page 15 Friday, February 22, 2002 11:34 AM