2002 MAZDA MODEL 626 oil dipstick

8-9
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Engine Compartment Overview
2.0-liter engineAutomatic transaxle fluid-level
dipstick (only for automatic
transaxle)
Brake/Clutch fluid reservoir
Battery Fuse block
Engine coolant
reservoirAir filter
Cooling system cap Engine oil-filler cap
Power steering fluid
reservoir
Windshield washer
fluid reservoir Engine oil dipstick
2.5-liter engine
Air filter
Cooling system cap
Engine coolant reservoir
Power steering fluid
reservoir
Battery
Fuse block
Automatic transaxle fluid-level
dipstick (only for automatic
transaxle)
Brake/Clutch fluid reservoir
Engine oil-filler cap
Windshield washer
fluid reservoir Engine oil dipstick
J94S.book Page 9 Saturday, June 23, 2001 1:04 PM

8-11
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal operating temperature.
3. Turn it off and wait 5 minutes for the oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and reinsert it fully.
5. Pull it out again and examine the level. It’s OK between L and F.
But if it’ s near at or below L, add
enough oil to bring the level to F. 6. Make sure the O-ring is positioned
properly before reinserting the
dipstick.
The distance between L and F on the
dipstick represents the following:





Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly —protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
Full
Low OK
2.0-liter engine
2.5-liter engine
Full
LowOK
Don
’t add engine oil over F. This may
cause engine damage.
L (US qt, Imp qt) 1.0 (1.06, 0.88)
Handling Used Engine Oil:Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
CAUTION
WARNING
J94S.book Page 11 Saturday, June 23, 2001 1:04 PM

8-12
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Changing engine oil
1. Warm up the engine for a few minutes and turn it off. Remove the oil-filler
cap.
2. Remove the drain plug and drain the oil into a suitable container. 3. Replace the plug tightly after the oil
has thoroughly drained.
4. Fill the engine with new oil to the F mark on the dipstick.
5. Securely replace the oil-filler cap.
6. Start the engine and inspect around the drain plug for leaks.
7. Turn it off and wait 5 minutes for the oil to return to the oil pan.
Check the oil level and fill to the F mark if
necessary.
Oil capacity (General reference only,
refer to Specifications section for
capacities.)
Changing oil filter
Because you need a special tool to
retighten the filter, an Authorized Mazda
Dealer should do the work.
Checking or Changing Engine Oil:Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don ’t check or
change the engine oil when the
engine is hot.
WARNING
2.0-liter engine
Loosen Tighten
Oil-filler cap
Drain plug
Oil-filler cap
Loosen Tighten
Drain plug
2.5-liter engine
NOTE
•
The indicated engine oil capacities
are for general reference purposes
only. When adding or changing oil,
verify the engine oil level with the
oil dipstick.
• Use only specified engine oil (page
10-4).
J94S.book Page 12 Saturday, June 23, 2001 1:04 PM

8-17
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Inspecting Power Steering Fluid
Level
Inspect the fluid level at each engine oil
change. Add fluid if necessary; it does not
require periodic changing.
The level must be kept between the HIGH
and LOW marks.
Visually examine the lines and hoses for
leaks and damage.
1. Park on a level surface, well off the
right-of-way, and set the parking brake
firmly.
2. Turn off the engine and allow it to cool. 3. Remove the filler cap and attached
dipstick.
4. Wipe them clean and put them back.
5. Remove again and inspect the level.
6. It must be between HIGH and LOW. Add fluid if necessary.
Don ’t overfill.
If new fluid is required frequently, consult
an Authorized Mazda Dealer.
Power Steering Fluid
To avoid damage to the power steering
pump, don’ t operate the vehicle for
long periods when the power steering
fluid level is low.
NOTE
Use specified power steering fluid
(page 10-4).
CAUTION
High
Low OK
J94S.book Page 17 Saturday, June 23, 2001 1:04 PM

10-5
Specifications
Form No. 8Q50-EA-01G





Capacities
(Approximate Quantities)
*The indicated engine oil capacities are for general reference purposes only. When adding
or changing oil, verify the engine oil level with the oil dipstick.






Dimensions
Unit: mm (in)






We i g h t s
Unit: kg (lb)
GVWR: Gross Vehicle Weight Rating
GAWR: Gross Axle Weight Rating
Unit
Item L US qt Imp qt
Engine oil
*
2.0-liter engine with oil filter
replacement
3.5 3.7 3.1
without oil filter
replacement 3.3 3.5 2.9
2.5-liter engine with oil filter
replacement
4.0 4.2 3.5
without oil filter
replacement 3.7 3.9 3.3
Coolant 7.5 7.9 6.6
Transaxle oil Manual transaxle 2.7 2.9 2.4
Automatic
transaxle
2.0-liter engine 8.86 9.37 7.80
2.5-liter engine 8.0 8.5 7.0
Fuel tank L US gal Imp gal
64.0 16.9 14.1
Overall length 4,760 (187.4)
Overall width 1,760 (69.3)
Overall height 1,400 (55.1)
Front tread 1,500 (59.1)
Rear tread 1,490 (58.7)
Wheelbase 2,670 (105.1) Model
Item 2.0-liter engine 2.5-liter engine
GVWR 1,771 (3,904) 1,827 (4,028)
GAWR Front 959 (2,114) 1,004 (2,214)
Rear 812 (1,790) 823 (1,814)
J94S.book Page 5 Saturday, June 23, 2001 1:04 PM