2002 MAZDA 6 low oil pressure

OUTLINE
R–3
R
SPECIFICATIONSA6E740201013203
*1: Engine coolant and engine oil are at specified level. Fuel is full. Spare tire, jack and tools are in designated position.
*
2: Difference between left and right must not exceed 1 °30'.*3: Distance between wheel center and fender brim is following. 4SD and 5HB front: 402 mm {15.82 in} (reference
value) 4SD and 5HB rear: 401 mm {15.78 in} (reference value), WGN (2WD) front: 405 mm {15.94 in}
(reference value) WGN (2WD) rear: 407 mm {16.02 in} (reference value)
Bold frames: New specifications
End Of Sie
Item Specification
New Mazda6 Current
Mazda6
GG (4SD, 5HB) GY (WGN 2WD) GY (WGN 4WD) GG (4SD, 5HB)
Engine type LF, MZR-CD
(RF Turbo) L8, LF, L3,
MZR-CD (RF Turbo) L3 L8, LF, L3
Fr o nt
suspension Type High-mount double wishbone (with double-pivoted lower arm(s))
Spring type Coil spring
Shock absorber type
Cylindrical, double-acting
(Low-pressure gas charged with rebound spring)
Stabilizer Type Torsion bar
Diameter (mm {in}) 23 {0.91}
Wheel
alignment
(Unloaded)*
1
Total toe-in (mm {in}) Tire: 2
±4 {0.08 ±0.16}, Rim inner: 1 ±3 {0.04 ±0.12}
(degree) 0 °11 ′±0°22 ′
Maximum
steering
angle inner
18 inch wheel specification vehicles: 36
°±3°
Except for above: 39 °±3°
outer 18 inch wheel specification vehicles: 30
°±3°
Except for above: 31 °±3°
Caster
angle*
2
(reference
value) normal 3
°47 ′±1° 3°40 ′±1° 3°35 ′±1° 3°47 ′±1°
elevated*33 °42' ±1° 3°35 ′±1° —3 °42' ±1 °
Camber
angle*
2
(reference
value) normal –0
°17 ′±1° –0°15 ′±1° –0°08 ′±1° –0°17 ′±1°
elevated*3–0 °10' ±1° –0°08 ′±1° —–0 °10' ±1°
Steering
axis
inclination
(reference
value) normal 5
°28 ′ 5°24 ′ 5°16 ′ 5°28 ′
elevated
*35 °18' 5 °16 ′ —5 °18'
Rear
suspension Type E-type multi-link
Spring type Coil spring
Stabilizer
Type Torsion bar
Diameter (mm {in})
4SD: 19 {0.75}
5HB: 18 {0.71}18 {0.71} 21 {0.83}
4SD: 19 {0.75}
5HB: 18 {0.71}
Shock absorber type Cylindrical,
double-acting
(Low-pressure gas charged) Cylindrical,
double-acting
(Low-pressure gas charged)/
(High-pressure
gas charged) Cylindrical,
double-acting
(High-pressure gas charged) Cylindrical,
double-acting
(Low-pressure gas charged)
Wheel
alignment
(Unloaded)*
1
Total toe-in (mm {in}) Tire: 2
±4 {0.08 ±0.16}, Rim inner: 1 ±3 {0.04 ±0.12}
(degree) 0 °11 ′±0°22 ′
Camber
angle*
2
normal –1 °13 ′±1° –1°06 ′±1° –1°03 ′±1° –1°13 ′±1°
elevated
*3–1 °05 ′±1° –0°58 ′±1° —–1 °05 ′±1°
Thrust angle (degree) 0 °±0°48 ′

REAR SUSPENSION
R–5
R
SUSPENSION CONTROL SYSTEMA6E741601013201Outline
•The self-leveling suspension is a system that adjusts the vehicle height according the amount of vehicle load.
This system will raise the rear of a vehicle, lowered due to a load placed on it, to the designated load level
* after
the vehicle has been driven a certain distance.
•The vehicle height adjustment is performed using a gas-pressurized pump function built into the rear shock
absorber.
•For the vehicle height to return to the designated load level, the vehicle must be driven approx. 5—6 km {3.1—
3.7 miles} in city driving conditions. (Distance will vary due to load and road conditions.)
•A load amount of approx. 140—300 kg {308—660 lb} at the rear axle will cause the vehicle height to be raised,
and any weight over that will prevent the vehicle from returning to the designated load level.
*: Designated load level is defined as the level at which the vehicle is with: a full fuel tank; engine coolant and oil at
specified levels; spare tire, jack and tools in designated positions; and four people, weighing 55 kg {121 lb} each,
riding in the vehicle.
Construction
.
REAR SUSPENSION
5
4
3
6
1
2
A6E74162001
1 Outlet check valve
2 Pump chamber
3 Low-pressure chamber4 High-pressure chamber
5Piston
6 Inlet check valve

R–6
REAR SUSPENSION
Operation
During leveling operation
•During shock absorber expansion, the inlet check valve opens due to negative pressure created in the pump
chamber, and oil is drawn into the pump chamber from the low-pressure chamber. During shock absorber
contraction, oil pressure in the pump chamber forces the outlet check valve to open, and oil in the pump
chamber flows through the pump cylinder into the high-pressure chamber. Due to this expansion and
contraction while driving, rod reaction force increases, and the vehicle height returns to the designated load
level. Also, similar to a regular shock absorber, damping is performed while driving with the damping valve.
.
Leveling operation completed
•When the vehicle height returns to the designated
load level, the volume of oil in the high-pressure
chamber increases and the piston rises. This
causes the pump chamber and the high-pressure
chamber to be connected at the pump rod notch,
and the expansion or contraction is completed.
.
87
5
4
3
6
1
2
A6E74162002
1 Pump chamber
2 Outlet check valve
3 Inlet check valve
4 Low-pressure chamber5 Damping valve
6 High-pressure chamber
7 Leveling operation (expansion)
8 Leveling operation (contraction)
1 Pump chamber
2Piston
3 Pump rod notch
4 High-pressure chamber
4
3
1
2
A6E74162003

REAR SUSPENSION, OUTLINE
R–7
R
During unloading of passengers and cargo
•When the vehicle height is higher than the
designated load level, oil flows back into the low-
pressure chamber from the high-pressure
chamber via the pump rod leveling port. As a
result, pressure in the high-pressure chamber
decreases, rod reaction force is reduced, and the
vehicle height returns to the designated load
level.
.
End Of Sie
SUPPLEMENTAL SERVICE INFORMATIONA6E740201013205•The following changes have been made since publication of the Mazda6 Workshop Manual (1730-1*-02C).
Front wheel alignment (WGN)
•Specifications have been added.
Rear wheel alignment (WGN)
•Specifications have been added.
Suspension control system (WGN)
•On-vehicle inspection procedure has been added.
Rear shock absorber (WGN)
•Removal/installation procedure has been added.
•Disposal procedure has been added.
Rear stabilizer (4WD)
•Removal/installation procedure has been added.
Trailing link (4WD)
•Removal/installation procedure has been added.
Rear crossmember (4WD)
•Removal/installation procedure has been added.
End Of Sie
1 Leveling port
2 Low-pressure chamber
3 High-pressure chamber
3
1
2
A6E74162004
OUTLINE

R–12
REAR SUSPENSION
Bracket Installation Note
1. Install the bracket as shown in the figure.
End Of SieREAR SHOCK ABSORBER DISPOSAL (WGN)A6E7416287002021. Lay the shock absorber on a level, horizontal surface.
2. Using a 2—3 mm {0.08—0.12 in} drill bit, drill a
hole in the high-pressure side (area indicated by
A), and allow the gas to escape.
Warning
•The oil in the shock absorber is
pressurized and could spray out. Be sure
to drill slowly and carefully.
3. Using a 2—3 mm {0.08—0.12 in} drill bit, drill a
hole in the low-pressure side (area indicated by
B).
4. Place the shock absorber with the hole drilled in
Step 3 turned downwards. Move the piston rod up
and down several times to drain out the oil.
5. Cut the tube at the end of the shock absorber,
and completely drain the oil out.
6. Properly dispose of the waste oil according to
waste disposal laws.
End Of Sie
106.5—112.5°
A6J74162006
A
A6J74161003
B
A6J74161006

TECHNICAL DATA
TD–3
TD
Recommended engine oil
Note
•The maintenance intervals on scheduled maintenance table (See GI–8 SCHEDULED MAINTENANCE
TABLE) can only be supported with the use of following oils.
End Of Sie
COOLING SYSTEMA6E931001001203
End Of Sie
FUEL AND EMISSION CONTROL SYSTEMA6E931001001204
*1: Excludes temporary idle speed drop just after the electrical loads are turned on.
End Of Sie
ItemSpecification
Diesel engine
MZR-CD (RF Turbo)
Engine oil GradeAPI CF CD, CE, CF-4
ACEA B1 or B3
B3B3 or B4
Viscosity (SAE) 5W-30 10W-40 5W-30, 10W-30
RemarksMazda genuine Dexelia oil e.g. —
ItemSpecification
Diesel engine
MZR-CD (RF Turbo)
Coolant capacity (L {US qt, Imp qt}) 9.0 {9.5, 7.9}
Radiator capCap valve opening pressure
94—122
{0.96—1.24, 13.7—17.6}
(kPa {kgf/cm
2, psi})
ThermostatType Wax, bottom-bypass
Initial-opening temperature (°C {°F})80—84
{176—183}
Full-opening temperature (°C {°F}) 95 {203}
Full-open lift (mm {in}) More than 8.5 {0.33}
Cooling fan Motor Current (A)4.4—7.4 (Cooling fan motor No.1)
6.3—9.3 (Cooling fan motor No.2)
ItemEngine
L3 (4WD)
Idle speed
*1(rpm) 650—750 (700±50)
ItemEngine
MZR-CD (RF Turbo)
Idle speed (rpm) 725—825 (775±50)
Idle-up speed (rpm) When A/C is operated 725—825 (775±50)
Boost relief pressure (kPa {mmHg, inHg}) Approx. –14.5 {–108, –4.27}

TD–4
TECHNICAL DATA
ENGINE ELECTRICAL SYSTEMA6E931001001205
*1: Back-up current is the constant flow of current present (for the audio unit, clock, PCM, etc.) when the engine
switch is off and with the key removed.
*
2: Must not be 0 A.
*3: Cold area
End Of Sie
CLUTCHA6E931001024201
End Of Sie
MANUAL TRANSAXLEA6E931001024202
ItemSpecification
Diesel engine
MZR-CD (RF Turbo)
BatteryElectrolyte gravity 1.27—1.29
Back-up current*
1(mA) Max.20
Type
95D31L, 115D31L
*3
Test load chart (A) Battery type95D31L (64) 250
115D31L (70) *3320
Slow-charge (A)Battery type
(5-hour rate)95D31L (64) 6.5—8.0
115D31L (70)
*37.0—8.5
Quick-charge
Battery type
(5-hour rate)95D31L (64) 40
(A/30 min)
115D31L (70)
*345
GeneratorStandard voltage (V)Ignition switch ON TerminalBB+
L Approx. 1
SB+
Idle [20°C {68°F}] TerminalB
14.1—14.7 L
S
Generated current*
2
(reference) (A) Engine speed (rpm)1,000 0—80
2,000 0—90
Starter No load testVoltage (V) 11
Current (A) Below 130
Item Specification
Clutch coverDiaphragm
spring fingersDepth mm {in} 0.6 {0.024}
Misalignment mm {in} 0.6 {0.024}
Maximum clearance of flatness of the
pressure platemm {in} 0.3 {0.012}
Flywheel Run out limit mm {in} 0.3 {0.012}
Item Specification
Manual transaxle typeA65M-R
Transaxle controlFloor-shift
Operation systemCable
Shift assistSynchromesh
Gear ratio1st 3.416
2nd 1.944
3rd 1.258
4th 0.902
5th 0.659
Reverse 3.252
Final gear ratio3.588
Transaxle oilGrade API service GL-4 or GL-5
Viscosity (All-season) SAE 75W-90
Capacity (approximate quantity)
2.30 {2.40, 2.00}
(L {US qt, Imp qt})

TD–6
TECHNICAL DATA
FRONT AND REAR AXLEA6E931001018201
End Of Sie
STEERING SYSTEMA6E931001034201
End Of Sie
Item Specification
FRONT DRIVE SHAFT
Shaft length
(Air in boot at atmospheric
pressure)(mm {in})Left sideMZR-CD (RF Turbo): 666.1—676.1 {26.23—26.61}
4WD: 667—677 {26.26—26.65}
Right sideMZR-CD (RF Turbo): 615.9—625.9 {24.25—24.64}
4WD: 631—641 {24.85—25.23}
REAR DRIVE SHAFT (4WD)
Shaft length
(Air in boot at atmospheric
pressure)(mm {in})Left side 805.4—815.4 {31.71—32.10}
Right side 852.4—862.4 {33.56—33.95}
REAR DIFFERENTIAL (4WD)
Pinion height (mm {in})–0.025—0.025 {–0.001—0.001}
Backlash of side gear and differential pinion (mm {in}) 0.1 {0.004} or less
Drive pinion preload (N·m kgf·cm, in·lbf) 1.3—1.8 {13.3—18.3, 11.5—15.9}
Backlash of drive pinion and
ring gear(mm {in})Standard 0.09—0.11 {0.0036—0.0043}
Minimum 0.05 {0.002}
Differential oilGrade API service GL-5
ViscosityAbove –18°C {0°F}: SAE 90
Below –18°C {0°F}: SAE 80
Capacity
(Approximate quantity)(L {US qt, lmp qt}) 1.00 {1.06, 0.88}
ELECTRONIC 4WD CONTROL SYSTEM
Differential oil temperature
sensor(kilohm)0°C {32°F} 91—100
10°C {50°F} 56—61
20°C {68°F} 35—39
30°C {86°F} 23—25
40°C {104°F} 14—17
50°C {122°F} 10—11
60°C {140°F} 7.1—7.9
70°C {158°F} 5.0—5.6
80°C {176°F} 3.6—4.0
4WD solenoid
(Rear differential oil temperature
at 20°C {68°F})(ohm) 1.5—2.0
Item Specification
ENGINE SPEED SENSING POWER STEERING
Power
steering oil
pumpOil pump fluid pressure 2WD (Except MZR-CD (RF Turbo)):
10.80—11.29 {110.2—115.1, 1,567—1,637}
MZR-CD (RF Turbo):
11.31—11.80 {115.4—120.3, 1,641—1,711}
4WD: 10.30—10.79 {105.1—110.0, 1,490—1,564} (MPa {kgf·cm
2, psi})
Gear housing fluid pressure 2WD (Except MZR-CD (RF Turbo)):
10.80—11.29 {110.2—115.1, 1,567—1,637}
MZR-CD (RF Turbo):
11.31—11.80 {115.4—120.3, 1,641—1,711}
4WD: 10.30—10.79 {105.1—110.0, 1,490—1,564} (MPa {kgf·cm
2, psi})
Power
steering
systemFluid type
ATF M-
III or equivalent (e.g. Dexron®II)
Capacity (Approximate quantity) MTX (Except MZR-CD (RF Turbo)): 0.80 {0.85, 0.70}
ATX (Except 4WD): 0.87 {0.92, 0.77}
MZR-CD (RF Turbo): 0.86 {0.91, 0.76}
4WD: 0.89 {0.94, 0.78} (L {US qt, Imp qt})