2002 MAZDA 6 brake fluid

ON-BOARD DIAGNOSTIC
P–21
P
DSC ON-BOARD DIAGNOSISA6E697067650201DTC Table
Note
•There is no change except for the code marked with an asterisk *
ON-BOARD DIAGNOSTIC
DTC
Diagnosis system component
WDS or
equivalent
B1318 DSC power supply
B1342 DSC HU/CM
B1483 Stop switch signal (with DSC only)
B1484 Stop switch signal (with DSC only)
B1486 Stop switch signal (with DSC only)
B1627 Reverse signal (with DSC only)
B2477 Module configuration (with DSC only)
C1095 Motor relay, pump motor
C1096 Motor relay, pump motor
C1119* Engine control system
C1125 Brake fluid level sensor (with DSC only)
C1140 DSC HU (pump) (with DSC only)
C1145 Right front wheel-speed sensor
C1148 Right front wheel-speed sensor/sensor rotor
C1155 Left front wheel-speed sensor
C1158 Left front wheel-speed sensor/sensor rotor
C1165 Right rear wheel-speed sensor
C1168 Right rear wheel-speed sensor/sensor rotor
C1175 Left rear wheel-speed sensor
C1178 Left rear wheel-speed sensor/sensor rotor
C1186 Fail-safe relay
C1194 Left front pressure reduction solenoid valve
C1198 Left front pressure retention solenoid valve
C1210 Right front pressure reduction solenoid valve
C1214 Right front pressure retention solenoid valve
C1233 Left front wheel-speed sensor/sensor rotor
C1234 Right front wheel-speed sensor/sensor rotor
C1235 Right rear wheel-speed sensor/sensor rotor
C1236 Left rear wheel-speed sensor/sensor rotor
C1242 Left rear pressure reduction solenoid valve
C1246 Right rear pressure reduction solenoid valve
C1250 Left rear pressure retention solenoid valve
C1254 Right rear ABS pressure retention solenoid valve
C1266 Fail-safe relay
C1280 Combine sensor (with DSC only)
C1400 Right front traction switch solenoid valve (with DSC only)
C1410 Left front traction switch solenoid valve (with DSC only)
C1414 DSC HU/CM (with DSC only)
C1507 DSC control (with DSC only)
C1508 TCS control
C1510 Right front solenoid valve, motor or wheel-speed sensor/sensor rotor
C1511 Left front solenoid valve, motor or wheel-speed sensor/sensor rotor
C1512 Right rear solenoid valve, motor or wheel-speed sensor/sensor rotor
C1513 Left rear solenoid valve, motor or wheel-speed sensor/sensor rotor

P–22
ON-BOARD DIAGNOSTIC
PID/DATA Monitor Table
Note
•There is no change except for the PID marked with an asterisk *
C1730 Combine sensor (with DSC only)
C1949* Combine sensor (with DSC only)
C1950* Combine sensor (with DSC only)
C1951 Combine sensor (with DSC only)
C1952 Combine sensor (with DSC only)
C1953 Brake fluid pressure sensor (with DSC only)
C1954 Brake fluid pressure sensor (with DSC only)
C1955 Steering angle sensor (with DSC only)
C1956 Steering angle sensor (with DSC only)
C1957 Right front DSC switch solenoid valve (with DSC only)
C1958 Left front DSC switch solenoid valve (with DSC only)
C1959 Combine sensor (with DSC only)
U1900 CAN communication
U2021 Invalid/fault data received
U2511* CAN communication
U2516 CAN communicationDTC
Diagnosis system component
WDS or
equivalent
PID Name
(Definition)Unit/Condition Condition/Specification ActionABS (ABS/
TCS) HU/CM or
DSC HU/CM
terminal
RPM
(Engine speed signal input)RPM•Engine is stopped: 0 RPM
•Engine is running: Indicates
engine speedInspect PCM.—
TRANSGR
*
(with DSC only)
(Transaxle gear position)FN4A-EL:
R/N/D/S/L
JA5AX-EL:
R/N/D•Selector lever position is
displayed
—R: R
—N: N
—D: D
—S: SInspect PCM, TR
switch, or DSC HU/
CM.
—
TRAC_SW
(TCS OFF switch input)ON/OFF•TCS (DSC) OFF switch is
depressed: ON
•TCS (DSC) OFF switch is
released: OFFInspect TCS (DSC)
OFF switch.
AA
TC LVAL (with DSC only)
(Traction switch solenoid valve
(LF-RR))ON/OFF•Solenoid valve is activated:
ON
•Solenoid valve is
deactivated: OFFInternal fault of DSC
HU/CM. Replace DSC
HU/CM.—
TC RVAL (with DSC only)
(Traction switch solenoid valve
(RF-LR))ON/OFF•Solenoid valve is activated:
ON
•Solenoid valve is
deactivated: OFFInternal fault of DSC
HU/CM. Replace DSC
HU/CM.—
L_DSC O (with DSC only)
(Stability control solenoid
valve (LF-RR))ON/OFF•Solenoid valve is activated:
ON
•Solenoid valve is
deactivated: OFFInternal fault of DSC
HU/CM. Replace DSC
HU/CM.—
R_DSC O (with DSC only)
(Stability control solenoid
valve (RF-LR))ON/OFF•Solenoid valve is activated:
ON
•Solenoid valve is
deactivated: OFFInternal fault of DSC
HU/CM. Replace DSC
HU/CM.—
CCNTABS
(Number of continuous codes)—DTC is detected: 1—255
DTC is not detected: 0Perform inspection
using appropriate
DTC.—

ON-BOARD DIAGNOSTIC
P–23
P
PMPSTAT
(Pump motor output state)ON/OFF•Pump motor is activated:
ON
•Pump motor is deactivated:
OFFInspect DSC HU/CM
—
BRK_FLUID (with DSC only)
(Brake fluid level sensor input)OK/LOW•Brake fluid is above LOW:
OK
•Brake fluid is below LOW:
LOWInspect brake fluid
level.
Inspect brake fluid
level sensor.—
BOO_ABS
(Brake pedal switch input)ON/OFF•Brake pedal is depressed:
ON
•Brake pedal is released:
OFFInspect brake switch.
ABS (ABS/
TCS): Y
DSC: L
ABS_LAMP
(ABS warning light driver
output state)ON/OFF•ABS warning light is
illuminated: ON
•ABS warning light is not
illuminated: OFFInspect ABS warning
light.
—
BRAKE_LMP
(BRAKE system warning light
output state)ON/OFF•BRAKE system warning
light is illuminated: ON
•BRAKE system warning
light is not illuminated: OFFInspect BRAKE
system warning light.
—
ABSRR_O
(Right rear ABS pressure
reduction solenoid valve
output state)ON/OFF•During ABS control: ON/
OFF
(solenoid valve is activated/
deactivated)
•Not ABS control: OFF
(solenoid valve is
deactivated)Internal fault of ABS
(ABS/TCS) or DSC
HU/CM. Replace ABS
(ABS/TCS) or DSC
HU/CM.—
ABSLR_O
(Left rear ABS pressure
reduction solenoid valve
output state)ON/OFF•During ABS or EBD control:
ON/OFF
(solenoid valve is activated/
deactivated)
•Not ABS and EBD control:
OFF
(solenoid valve is
deactivated)Internal fault of ABS
(ABS/TCS) or DSC
HU/CM. Replace ABS
(ABS/TCS) or DSC
HU/CM.—
ABSRF_O
(Right front ABS pressure
reduction solenoid valve
output state)ON/OFF•During ABS control: ON/
OFF
(solenoid valve is activated/
deactivated)
•Not ABS control: OFF
(solenoid valve is
deactivated)Internal fault of ABS
(ABS/TCS) or DSC
HU/CM. Replace ABS
(ABS/TCS) or DSC
HU/CM.—
ABSLF_O
(Left front ABS pressure
reduction solenoid valve
output state)ON/OFF•During ABS control: ON/
OFF
(solenoid valve is activated/
deactivated)
•Not ABS control: OFF
(solenoid valve is
deactivated)Internal fault of ABS
(ABS/TCS) or DSC
HU/CM. Replace ABS
(ABS/TCS) or DSC
HU/CM.—
ABSRR_I
(Right rear ABS pressure
reduction solenoid valve
output state)ON/OFF•During ABS control: ON/
OFF
(solenoid valve is activated/
deactivated)
•Not ABS control: OFF
(solenoid valve is
deactivated)Internal fault of ABS
(ABS/TCS) or DSC
HU/CM. Replace ABS
(ABS/TCS) or DSC
HU/CM.—
ABSLR_I
(Left rear ABS pressure
retention solenoid valve output
state)ON/OFF•During ABS or EBD control:
ON/OFF
(solenoid valve is activated/
deactivated)
•Not ABS and EBD control:
OFF
(solenoid valve is
deactivated)Internal fault of ABS
(ABS/TCS) or DSC
HU/CM. Replace ABS
(ABS/TCS) or DSC
HU/CM.— PID Name
(Definition)Unit/Condition Condition/Specification ActionABS (ABS/
TCS) HU/CM or
DSC HU/CM
terminal

P–24
ON-BOARD DIAGNOSTIC
ABSRF_I
(Right front ABS pressure
retention solenoid valve output
state)ON/OFF•During ABS control: ON/
OFF
(solenoid valve is activated/
deactivated)
•Not ABS control: OFF
(solenoid valve is
deactivated)Internal fault of ABS
(ABS/TCS) or DSC
HU/CM. Replace ABS
(ABS/TCS) or DSC
HU/CM.—
ABSLF_I
(Left front ABS pressure
retention solenoid valve output
state)ON/OFF•During ABS control: ON/
OFF
(solenoid valve is activated/
deactivated)
•Not ABS control: OFF
(solenoid valve is
deactivated)Internal fault of ABS
(ABS/TCS) or DSC
HU/CM. Replace ABS
(ABS/TCS) or DSC
HU/CM.—
ABSVLVRLY
(Fail-safe relay output state)ON/OFF•Fail-safe relay is
activated: ON
•Fail-safe relay is
deactivated: OFFInspect ABS (ABS/
TCS) or DSC HU/CM.
—
ABSPMPRLY
(Motor relay output state)ON/OFF•Motor relay is activated: ON
•Motor relay is deactivated:
OFFInspect ABS (ABS/
TCS) or DSC HU/CM.—
SWA POS (with DSC only)
(Steering angle sensor input)ANGLE•Steering wheel is in neutral
position: 0 DEG
•Steering wheel is turned to
left: Changes between
0 DEG and -1,638.40 DEG
•Steering wheel is turned to
right: Changes between
0 DEG and 1,638.35 DEGInspect steering angle
sensor.
R, U, W, X
LF_WSPD
(Left front wheel-speed sensor
input)SPEED•Vehicle is stopped: 0 KPH
{0 MPH}
•Vehicle is driving: Indicates
vehicle speedInspect wheel-speed
sensor/sensor rotor.ABS (ABS/
TCS): E, I
DSC: F, J
RF_WSPD
(Right front wheel-speed
sensor input)SPEED•Vehicle is stopped: 0 KPH
{0 MPH}
•Vehicle is driving: Indicates
vehicle speedInspect wheel-speed
sensor/sensor rotor.ABS (ABS/
TCS): D, G
DSC: I, M
LR_WSPD
(Left rear wheel-speed sensor
input)SPEED•Vehicle is stopped: 0 KPH
{0 MPH}
•Vehicle is driving: Indicates
vehicle speedInspect wheel-speed
sensor/sensor rotor.ABS (ABS/
TCS): C, F
DSC: N, Q
RR_WSPD
(Right rear wheel-speed
sensor input)SPEED•Vehicle is stopped: 0 KPH
{0 MPH}
•Vehicle is driving: Indicates
vehicle speedInspect wheel-speed
sensor/sensor rotor.ABS (ABS/
TCS): A, B
DSC: H, K
LAT ACC (with DSC only)
(Lateral-G sensor input)ACCELERATION•Vehicle is stopped or driving
straight: 0 G
•Cornering to left: Changes
between 0 G and 1.27 G
•Cornering to right: Changes
between 0 G and -1.28 GInspect ABS wheel-
speed sensor/sensor
rotor.
O
YAW_RATE (with DSC only)
(Yaw rate sensor input)ACCELERATION•Vehicle is stopped or driving
straight: 0 DG/S
•Cornering to left: Changes
between 0 DG/S and 127
DG/S
•Cornering to right: Changes
between 0 DG/S and -128
DG/SInspect combine
sensor.
T
MCYLI P (with DSC only)
(Brake fluid pressure sensor
input)PRESSURE•Brake pedal is released:
0 MPa
•Brake pedal is depressed:
Changes between 0 MPa
and 25.5 MPaInspect DSC HU/CM.
— PID Name
(Definition)Unit/Condition Condition/Specification ActionABS (ABS/
TCS) HU/CM or
DSC HU/CM
terminal

T–4
MULTIPLEX COMMUNICATION SYSTEM
SYSTEM WIRING DIAGRAMA6E811155430203
.
End Of SieCAN SIGNAL-CHARTA6E811155430204
OUT: Output (sends signal)
IN: Input (receives signal)
1
2
67
3
8
4
5
ROAF AG
HG
2M2J2W
2X
9
10
CAN_L
CAN_H
A6E81111102
1PCM
2 DSC HU/CM (with DSC)
3 ABS (ABS/TCS) HU/CM (with ABS (ABS/TCS))
4 Data link connector-2
5 Instrument cluster
6 TCM (JA5AX-EL)7 4WD control module (4WD)
8Twist pair
9 2R (except MZR-CD (RF Turbo))
39 (MZR-CD (RF Turbo))
10 2U (except MZR-CD (RF Turbo))
13 (MZR-CD (RF Turbo))
SignalMultiplex module
PCM TCMABS (ABS/TCS)
HU/CM or
DSC HU/CM4WD control
moduleInstrument
cluster
Accelerator pedal position
(MZR-CD (RF Turbo))OUT IN IN–IN
Air induction type OUT–IN––
ATF temperature IN OUT–––
AT warning light conditions
(JA5AX-EL)IN OUT––IN
Battery reconnection
(except MZR-CD (RF
Turbo))OUT IN–––
Brake system configuration
(EBD/ABS/TCS/DSC)IN–OUT–IN
Brake system
statusABS IN–OUT––
EBD/ABS/
TCS/DSC––OUT IN IN
Brake system warning light
conditions (brake fluid level
sensor)––IN–OUT
Country OUT–IN––
Coupling torque (with
DSC)––IN OUT–
Coupling torque request
(with DSC)––OUT IN–

TECHNICAL DATA
TD–5
TD
End Of SieAUTOMATIC TRANSAXLEA6E931001024203
End Of Sie
PROPELLER SHAFTA6E931001024204
End Of Sie
Item Specification
Transaxle typeJA5AX-EL
Line pressure
(kPa {kgf/cm
2, psi})D range, M range (2GR)Idle 290—490 {3.0—5.0, 42—71}
Stall 1,550—1,750 {15.8—17.8, 225—254}
M range (1GR), R positionIdle 550—750 {5.6—7.6, 80—109}
Stall 1,550—1,750 {15.8—17.8, 225—254}
Engine stall speed
D, M (1GR, 2GR), R 2,200—2,600
(rpm)
Time lag (second)N-D Approx. 0.5—1.0
N-R Approx. 0.6—1.0
Transaxle fluid
temperature (TFT)
sensor-20 °C {−4 °F} 15.87—17.54
0 °C {32 °F} 5.73—6.33
20 °C {68 °F} 2.38—2.63
40 °C {104 °F} 1.10—1.22
60 °C {140 °F} 0.56—0.62
80 °C {176 °F} 0.31—0.34
(kilohm) 100 °C {212 °F} 0.18—0.20
120 °C {248 °F} 0.11—0.12
130 °C {266 °F} 0.09—0.10
Input/turbine
speed sensor(ohm) ATF temperature: 20 °C {68 °F} 513—627
Intermediate
sensor(ohm) ATF temperature: 20 °C {68 °F} 513—627
Vehicle
speedometer
sensor(ohm) ATF temperature: 20 °C {68 °F} 513—627
Solenoid valves (ohm)Shift solenoid A 14—18
Shift solenoid B 14—18
Shift solenoid C 14—18
Neutral shift solenoid valve 14—18
Reduction timing solenoid valve 14—18
TCC solenoid valve 12.0—13.2
2-4 brake solenoid valve 2.6—3.2
High clutch solenoid valve 2.6—3.2
Pressure control solenoid 2.6—3.2
Automatic transaxle fluid
(ATF)Type
M-
III or equivalent (e.g. Dexron ® III )
Capacity (Approximate quantity) (L {US qt, Imp qt}) 8.3 {8.8, 7.3}
Transfer oilGrade API service GL-5
Viscosity SAE 80W-90
Capacity (Approximate quantity) (L {US qt, Imp qt}) 0.62 {0.65, 0.54}
Item Specification
Runout limit mm {in} 0.3 {0.01}
Starting torqueN·m
{kgf·cm}0.29—0.78 {3.0—7.9}