2002 MAZDA 6 window

WINDOW GLASS
S–19
S
6. Apply sealant to the area of the glass surface as
shown in the figure.
7. Set the position of the front windshield glass and
insert a pin into the body. Install the glass.
8. Keeping the measurement of the molding lip gap
within specification, press completely along the
perimeter of the glass.
9. Install the following points.
(1) Install the rear wiper motor.
(2) Install the liftgate lower trim.
(3) Install the liftgate side trim.
(4) Install the liftgate upper trim.
10. Allow the sealant to harden completely.
Sealant hardening time: 24 hours
End Of Sie
mm {in} 5 {0.20}11
{0.43}
APPLY SEALANT
TO THIS AREA.
A6A7738W113
PIN
PIN
A6E77381114
mm {in}
C
CA
A
B
SEC. A—A
SEC. C
—CSEC. B
—B
17.5 {0.69}
27.7 {1.09} 26.4 {1.04}
B
A6E77381115

T–30
AUDIO AND NAVIGATION SYSTEM
NOISE FILTER REMOVAL/INSTALLATIONA6E812466869201Brake Light Noise Filter
1. Remove the noise filter according to the NOISE FILTER REMOVAL/INSTALLATION procedure for the 4SD.
2. Install in the reverse order of removal.
Rear Window Defroster Noise Filter
1. Disconnect the negative battery cable.
2. Remove the liftgate lower trim.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of SieCONDENSER REMOVAL/INSTALLATIONA6E8124668692021. Disconnect the negative battery cable.
2. Remove the liftgate lower trim.
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
End Of Sie
AUDIO AND NAVIGATION SYSTEM
1Bolt
2Screw
3 Connector
4 Noise filter
2
3
4
8.9—12.7 N·m
{90—130 kgf·cm,
79—11 2 in·lbf}
1
A6E81241109
1Bolt
2 Connector
3 Condenser
1
3
2
1
2
3
3
2
1
N·m {kgf·cm, in·lbf} 8.9—12.7
{90—130, 79—112}
8.9—12.7
{90—130, 79—112} 8.9—12.7
{90—130, 79—112}
A6E81241122

T–36
AIR BAG SYSTEM
Deployment Procedure for Inside of Vehicle (Only When Vehicle Is To Be Scrapped)
1. Inspect the SST (Deployment tool).
2. Move the vehicle to an open space, away from strong winds, and close all the doors and windows.
3. Turn the ignition switch to LOCK position.
4. Disconnect the negative battery cable and wait for more than 1 minute.
5. Follow the appropriate procedure for deploying the driver-side air bag module, passenger-side air bag module,
side air bag module, curtain air bag module, or pre-tensioner seat belt.
Curtain air bag module (WGN)
1. Remove the headliner.
2. Disconnect the curtain air bag module connector.
3. Connect the SST (Adapter harness) to the curtain
air bag module.
4. Connect the SST (Deployment tool) to the SST
(Adapter harness).
5. Connect the red clip of the SST (Deployment tool)
to the positive battery terminal and the black clip
to the negative battery terminal.
6. Verify that the red light on the SST (Deployment
tool) is illuminated.
7. Make sure all persons are standing at least 6 m
{20 ft} from the vehicle.
8. Press the activation switch on the SST
(Deployment tool) to deploy the curtain air bag
module.
Deployment Procedure for Outside of Vehicle
1. Inspect the SST (Deployment tool).
2. Turn the ignition switch to LOCK position.
3. Disconnect the negative battery cable and wait for more than 1 minute.
4. Follow the appropriate procedure for deploying the driver-side air bag module, passenger-side air bag module,
side air bag module, curtain air bag module, or pre-tensioner seat belt.
49 L066 002
CURTAIN
AIR BAG MODULE
CONNECTOR
A6E81301112
49 L066 002
49 H066 002
A6E8130W151
49 H066 002
ACTIVATION
SWITCH
A6E8130W028

CONTROL SYSTEM
U–17
U
1B +5 V•Air mix actuator
•Airflow mode
actuator
•Solar radiation
sensorIgnition switch at ON
position
5.0•Inspect for short circuit
(Climate control unit— air
mix actuator, airflow mode
actuator, solar radiation
sensor: 1B—B, B, A)
•Inspect air mix actuator
•Inspect airflow mode
actuator
•Inspect solar radiation
sensor
•Inspect terminal voltage of
climate control unit
connector (2H, 2L)
Ignition switch at LOCK
positionBelow 1.0•Replace climate control unit
1C Blower motor
control signalPower MOS FET Fan switch is OFF Below 1.0•Inspect terminal voltage of
climate control unit (1A)
Fan switch is at manual
LO4.1
Fan switch is at manual
HI7.9
1D—— —— —
1E Rear window
defroster SW
signalRear window
defroster relayRear window defroster
switch is off
12•Inspect for continuity or
short circuit (Climate control
unit—rear window defroster
relay: 1E—E)
•Inspect rear window
defroster relay
Rear window defroster
switch is on Below 1.0•Inspect terminal voltage of
climate control unit (2H, 2L)
•Inspect center panel
1F On-board
diagnostic signalA/C check
connectorTerminal A of A/C check
connector is shorted. Below 1.0•Inspect for continuity
(Climate control unit—A/C
check connector: 1F—A)
Other
5.4•Inspect short circuit (Climate
control unit—A/C check
connector: 1F—A)
•Inspect terminal voltage of
climate control unit (2H, 2L)
1G—— —— —
1H—— —— —
1I GND•Cabin
temperature
sensor
•Evaporator
temperature
sensor
•Ambient
temperature
sensor
•Water
temperature
sensor
•Air mix actuator
•Airflow mode
actuatorUnder any condition
Below 1.0•Inspect terminal voltage of
climate control unit (2L)
1J Water heater
selectGround Under any condition
Below 1.0•Inspect for continuity
(Climate control unit—
ground: 1J—GND)
•Inspect center panel Terminal Signal Connected to Test condition Voltage (V) Action

SPECIAL TOOLS
ST–7
ST
STEERING SYSTEMA6E941001034201
End Of Sie
BRAKING SYSTEMA6E941001020201
End Of Sie
SUSPENSIONA6E941001013201
End Of Sie
BODYA6E941001047201
End Of Sie
49 1232 670B
Power steering
gauge set49 H002 671
Adapter49 G032 3A4
Power steering
gauge adapter
set
49 T028 3A0
Ball joint puller
set49 F032 301
Power steering
pump hanger49 E017 5A0
Engine support
set
49 0259 770B
Flare nut
wrench49 FA18 602
Disc brake
piston wrench49 0221 600C
Disc brake
expand tool
WDS 49 G066 001
Adapter
harness
(with ABS)49 G066 004
Adapter
harness
(with DSC)
49 G033 102
Handle49 G033 106
Attachment
—
49 0305 870A
Window tool set49 G050 1A0
Sealant
remover
—