T–28
WARNING AND INDICATOR SYSTEM
Fuel gauge sender cap removal note
1. Using the SST, remove the fuel gauge sender
cap.
Fuel Gauge Sender Cap Installation Note
1. Verify that the fuel tank mark is aligned with the
fuel gauge sender sub-unit mark as shown.
2. Using the SST, tighten the fuel gauge sender cap
without shifting the mark.
Tightening torque
80—90 N·m {8.2—9.1 kgf·m, 60—66 ft·lbf}
Fuel leak inspection after fuel gauge sender sub-unit installation
1. Drive the vehicle.
2. Perform a quick start and a hard brake 5—6 times.
3. Stop the vehicle.
4. Verify that there is no fuel leakage near the fuel pump unit in the vehicle interior.
End Of Sie
FUEL GAUGE SENDER UNIT INSPECTIONA6E8118609602021. Move the float to the topmost and bottommost positions, and verify that the resistance between terminals A and
B of the unit and the position of the float are as indicated in the figure.
•If they are not as indicated, replace the fuel gauge sender unit.
End Of Sie
49 T042 001A
A6J81182105
FUEL GAUGE
SENDER
SUB-UNIT MARK
MARK
A6E81182002
4WD
44.4—58.4
{1.75—2.29}
TOPMOST
POSITION
BOTTOMMOST
POSITION BASIC
POSITION
ARM
FULCRUM
72.9—86.9
{2.88—3.42}AB
*
53.9—60.9
{2.13—2.39}
TOPMOST
POSITION
BOTTOMMOST
POSITION BASIC
POSITION
ARM
FULCRUM
89.7—96.7
{3.54—3.80}
mm {in}
FUEL GAUGE SENDER UNIT
FUEL GAUGE SENDER SUB-UNIT
6.1—8.1 ohms
57.6—59.6 ohms7.2—9.2 ohms
66.5—68.5 ohms
A6E81181103
TECHNICAL DATA
TD–5
TD
End Of SieAUTOMATIC TRANSAXLEA6E931001024203
End Of Sie
PROPELLER SHAFTA6E931001024204
End Of Sie
Item Specification
Transaxle typeJA5AX-EL
Line pressure
(kPa {kgf/cm
2, psi})D range, M range (2GR)Idle 290—490 {3.0—5.0, 42—71}
Stall 1,550—1,750 {15.8—17.8, 225—254}
M range (1GR), R positionIdle 550—750 {5.6—7.6, 80—109}
Stall 1,550—1,750 {15.8—17.8, 225—254}
Engine stall speed
D, M (1GR, 2GR), R 2,200—2,600
(rpm)
Time lag (second)N-D Approx. 0.5—1.0
N-R Approx. 0.6—1.0
Transaxle fluid
temperature (TFT)
sensor-20 °C {−4 °F} 15.87—17.54
0 °C {32 °F} 5.73—6.33
20 °C {68 °F} 2.38—2.63
40 °C {104 °F} 1.10—1.22
60 °C {140 °F} 0.56—0.62
80 °C {176 °F} 0.31—0.34
(kilohm) 100 °C {212 °F} 0.18—0.20
120 °C {248 °F} 0.11—0.12
130 °C {266 °F} 0.09—0.10
Input/turbine
speed sensor(ohm) ATF temperature: 20 °C {68 °F} 513—627
Intermediate
sensor(ohm) ATF temperature: 20 °C {68 °F} 513—627
Vehicle
speedometer
sensor(ohm) ATF temperature: 20 °C {68 °F} 513—627
Solenoid valves (ohm)Shift solenoid A 14—18
Shift solenoid B 14—18
Shift solenoid C 14—18
Neutral shift solenoid valve 14—18
Reduction timing solenoid valve 14—18
TCC solenoid valve 12.0—13.2
2-4 brake solenoid valve 2.6—3.2
High clutch solenoid valve 2.6—3.2
Pressure control solenoid 2.6—3.2
Automatic transaxle fluid
(ATF)Type
M-
III or equivalent (e.g. Dexron ® III )
Capacity (Approximate quantity) (L {US qt, Imp qt}) 8.3 {8.8, 7.3}
Transfer oilGrade API service GL-5
Viscosity SAE 80W-90
Capacity (Approximate quantity) (L {US qt, Imp qt}) 0.62 {0.65, 0.54}
Item Specification
Runout limit mm {in} 0.3 {0.01}
Starting torqueN·m
{kgf·cm}0.29—0.78 {3.0—7.9}
