2002 JEEP LIBERTY Camshaft position

(1) Set crankshaft sprocket to TDC by aligning the
sprocket with the arrow on the oil pump housing.
(2) Set camshafts timing marks so that the
exhaust camshaft sprocket is a 1/2 notch below the
intake camshaft sprocket (Fig. 99).
CAUTION: Ensure that the arrows on both camshaft
sprockets are facing up.
(3) Install timing belt. Starting at the crankshaft,
go around the water pump sprocket, idler pulley,
camshaft sprockets and then around the tensioner
(Fig. 100).
(4) Move the exhaust camshaft sprocket counter-
clockwise (Fig. 100) to align marks and take up belt
slack.
(5) Inserta6mmAllen wrench into the hexagon
opening located on the top plate of the belt tensioner
pulley. Rotate the top plateCOUNTERCLOCK-
WISE. The tensioner pulley will move against the
belt and the tensioner setting notch will eventually
start to move clockwise. Watching the movement of
the setting notch, continue rotating the top plate
counterclockwise until the setting notch is aligned
with the spring tang (Fig. 101). Using the allen
wrench to prevent the top plate from moving, torque
the tensioner lock nut to 30 N´m (22 ft. lbs.). Setting
notch and spring tang should remain aligned after
lock nut is torqued.
(6) Remove allen wrench and torque wrench.NOTE: Repositioning the crankshaft to the TDC
position must be done only during the CLOCKWISE
rotation movement. If TDC is missed, rotate a fur-
ther two revolutions until TDC is achieved. DO NOT
rotate crankshaft counterclockwise as this will
make verification of proper tensioner setting impos-
sible.
(7) Once the timing belt has been installed and
tensioner adjusted, rotate the crankshaft CLOCK-
WISE two complete revolutions manually for seating
of the belt, until the crankshaft is repositioned at the
TDC position. Verify that the camshaft and crank-
shaft timing marks are in proper position (Fig. 102).
Fig. 99 Camshaft Sprocket Alignment
1 - CAMSHAFT SPROCKET-EXHAUST
2 - CAMSHAFT SPROCKET-INTAKE
3 - 1/2 NOTCH LOCATION
Fig. 100 Timing Belt - Installation - Typical
1 - ROTATE CAMSHAFT SPROCKET TO TAKE UP BELT SLACK
2 - CAMSHAFT TIMING MARKS 1/2 NOTCH LOCATION
3 - CRANKSHAFT AT TDC
4 - INSTALL BELT IN THIS DIRECTION
KJENGINE9s-57
TIMING BELT AND SPROCKET(S) (Continued)

SPECIFICATIONS
FUEL SYSTEM PRESSURE
339 kPa +/- 34 kPa (49.2 psi +/- 2 psi).
TORQUE
DESCRIPTION N-m Ft. Lbs. In. Lbs.
Accelerator Pedal Bracket Mounting Nuts 12 - 105
Crankshaft Position Sensor - 2.4L 28 21 -
Crankshaft Position Sensor - 3.7L 28 21 -
Camshaft Position Sensor - 2.4L 12 - 106
Camshaft Position Sensor - 3.7L 12 - 106
Engine Coolant Temperature Sensor 11 - 96
EVAP Canister-to-Body Bolts 48 35 -
EVAP Canister-to-Canis. Bracket Bolt/Nut 11 - 100
Fuel Filler Hose Clamp at Tank 3 - 30
Fuel Filler Housing-to-Body Screws 2 - 17
Fuel Filter Mounting Nut at Tank 5.5 - 49
Fuel Pump Module Access Plate Nuts 3 - 26
Fuel Rail Mounting Bolts - 3.7L 11 - 100
Fuel Rail Mounting Bolts - 2.4L 28 - 250
Fuel Tank Heat Sheild Nuts 5.5 - 49
Fuel Tank Mounting Strap Bolts 61 45 -
Fuel Tank Skid Plate and Trailer Hitch 88 65 -
IAC Motor Mounting Screws 7 - 60
Leak Detection Pump Mounting Bracket-to-Fuel
Tank Nuts5.5 - 49
Leak Detection Pump-to-Bracket Nuts 1.2 - 11
Map Sensor Mounting Screws 3 - 25
PCM-to-Mounting Bracket Mounting Screws 4 - 35
Power Steering Pressure Switch 14-22 - 124-195
TPS Mounting Screws 7 - 60
Throttle Body Mounting Bolts 11 - 100
Oxygen Sensors 30 22 -
KJFUEL DELIVERY 14 - 5
FUEL DELIVERY (Continued)

(M)Malfunction Indicator Lamp (MIL) illuminated during engine operation if this DTC was recorded
(depending if required by CARB and/or EPA). MIL is displayed as an engine icon on instrument panel.
(G)Generator lamp illuminated
Generic Scan
Tool P-CodeDRB Scan Tool Display Brief Description of DTC
P0336 (M) Crankshaft Position (CKP) Sensor
SignalProblem with voltage signal from CKP.
P0340 (M) No Cam Signal At PCM No fuel sync
P0341 (M) Camshaft Position (CMP) Sensor
SignalProblem with voltage signal from CMP.
P0350 Ignition Coil Draws Too Much
CurrentA coil (1-5) is drawing too much current.
P0351 (M) Ignition Coil # 1 Primary Circuit Peak primary circuit current not achieved with maximum
dwell time.
P0352 (M) Ignition Coil # 2 Primary Circuit Peak primary circuit current not achieved with maximum
dwell time.
P0353 (M) Ignition Coil # 3 Primary Circuit Peak primary circuit current not achieved with maximum
dwell time.
P0354 (M) Ignition Coil # 4 Primary Circuit Peak primary circuit current not achieved with maximum
dwell time (High Impedance).
P0355 (M) Ignition Coil # 5 Primary Circuit Peak primary circuit current not achieved with maximum
dwell time (High Impedance).
P0356 (M) Ignition Coil # 6 Primary Circuit Peak primary circuit current not achieved with maximum
dwell time (high impedance).
P0357 (M) Ignition Coil # 7 Primary Circuit Peak primary circuit current not achieved with maximum
dwell time (high impedance).
P0358 (M) Ignition Coil # 8 Primary Circuit Peak primary circuit current not achieved with maximum
dwell time (high impedance).
P0370 Fuel Injection Pump Speed/Position
Sensor Sig LostProblem caused by internal fuel injection pump failure.
P0380 (M) Intake Air Heater Relay #1 Control
CircuitProblem detected in #1 air heater solenoid/relay circuit
(not heater element)
P0381 (M) Wait To Start Lamp Inoperative Problem detected in wait-to-start bulb circuit.
P0382 (M) Intake Air Heater Relay #2 Control
CircuitProblem detected in #2 air heater solenoid/relay circuit
(not heater element)
P0387 Crankshaft Position Sensor Supply
Voltage Too LowCKP sensor voltage input below the minimum acceptable
voltage.
P0388 Crankshaft Position Sensor Supply
Voltage Too HighCKP sensor voltage input above the maximum acceptable
voltage.
PO0400 Diesel EGR System Failure
P0401 EGR System Failure Required change in air/fuel ration not detected during
diagnostic test.
P0403 EGR Solenoid Circuit An open or shorted condition detected in the EGR
solenoid control circuit.
P0404 EGR Position Sensor Rationality EGR position sensor signal does not correlate to EGR
duty cycle.
P0405 EGR Position Sensor Volts Too Low EGR position sensor input below the acceptable voltage
range.
KJEMISSIONS CONTROL 25 - 7
EMISSIONS CONTROL (Continued)

SPECIFICATIONS
TORQUE
DESCRIPTION N-m Ft. Lbs. In. Lbs.
Accelerator Pedal Bracket
Mounting Nuts12 - 105
Crankshaft Position Sensor - 2.4L 28 21 -
Crankshaft Position Sensor - 3.7L 28 21 -
Camshaft Position Sensor - 2.4L 12 - 106
Camshaft Position Sensor - 3.7L 12 - 106
Engine Coolant Temperature
Sensor11 - 9 6
EVAP Canister-to-Body Bolts 48 35 -
EVAP Canister-to-Canis. Bracket
Bolt/Nut11 - 100
Fuel Filler Hose Clamp at Tank 3 - 30
Fuel Filler Housing-to-Body
Screws2-17
Fuel Filter Mounting Nut at Tank 5.5 - 49
Fuel Pump Module Access Plate
Nuts3-26
Fuel Rail Mounting Bolts - 3.7L 11 - 100
Fuel Rail Mounting Bolts - 2.4L 28 - 250
Fuel Tank Heat Sheild Nuts 5.5 - 49
Fuel Tank Mounting Strap Bolts 61 45 -
Fuel Tank Skid Plate and Trailer
Hitch88 65 -
IAC Motor Mounting Screws 7 - 60
Leak Detection Pump Mounting
Bracket-to-Fuel Tank Nuts5.5 - 49
Leak Detection Pump-to-Bracket
Nuts1.2 - 11
Map Sensor Mounting Screws 3 - 25
PCM-to-Mounting Bracket
Mounting Screws4-35
Power Steering Pressure Switch 14-22 - 124-195
TPS Mounting Screws 7 - 60
Throttle Body Mounting Bolts 11 - 100
Oxygen Sensors 30 22 -
25 - 26 EVAPORATIVE EMISSIONSKJ
EVAPORATIVE EMISSIONS (Continued)

BRAKE CALIPERS - OPERATION, DISC.....5-14
BRAKE CALIPERS - REMOVAL, DISC......5-14
BRAKE COMPONENTS, SPECIFICATIONS....5-6
BRAKE DRUM - DIAGNOSIS AND
TESTING............................5-27
BRAKE DRUM MACHINING - STANDARD
PROCEDURES........................5-27
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-26
BRAKE FLUID, SPECIFICATIONS..........5-27
BRAKE HOSE - INSTALLATION, FRONT.....5-10
BRAKE HOSE - INSTALLATION, REAR......5-10
BRAKE HOSE - REMOVAL, REAR..........5-9
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-13
BRAKE INDICATOR - DIAGNOSIS AND
TESTING...........................8J-14
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-13
BRAKE LAMP SWITCH - DESCRIPTION . . . 8L-16
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-17
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-18
BRAKE LAMP SWITCH - OPERATION.....8L-16
BRAKE LAMP SWITCH - REMOVAL......8L-17
BRAKE LINE AND HOSES - DIAGNOSIS
AND TESTING.........................5-8
BRAKE LINES - DESCRIPTION............5-8
BRAKE PADS - INSTALLATION, FRONT.....5-11
BRAKE PADS - REMOVAL, FRONT........5-11
BRAKE ROTOR - DIAGNOSIS AND
TESTING, DISC.......................5-18
BRAKE ROTOR - STANDARD
PROCEDURE, DISC....................5-19
BRAKE SHOES - INSTALLATION, DRUM....5-11
BRAKE SHOES - REMOVAL, DRUM.......5-11
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-3
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DESCRIPTION....21-124
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DIAGNOSIS
AND TESTING......................21-125
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - OPERATION.....21-125
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION.......................8J-13
BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-13
BRAKES - ABS - DESCRIPTION...........5-32
BRAKES - ABS - OPERATION............5-32
BRAKES - ABS - SPECIFICATIONS........5-33
BRAKES - BASE - DESCRIPTION...........5-2
BRAKES - BASE - WARNING..............5-2
BRAKES, SPECIAL TOOLS - BASE.........5-7
BRAKING SYSTEM - DIAGNOSIS AND
TESTING, ANTILOCK...................5-33
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH............24-12
BUCKLE - INSTALLATION, FRONT SEAT
BELT ..............................8O-26
BUCKLE - INSTALLATION, REAR SEAT
BELT ..............................8O-35
BUCKLE - REMOVAL, FRONT SEAT BELT . . 8O-25
BUCKLE - REMOVAL, REAR SEAT BELT . . . 8O-34
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE........................8F-10
BULB - INSTALLATION, ASH RECEIVER
LAMP..............................8L-71
BULB - INSTALLATION, CARGO LAMP....8L-73
BULB - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP................8L-19
BULB - INSTALLATION, COMPASS
MINI-TRIP ILLUMINATION..............8L-75
BULB - INSTALLATION, COURTESY
LAMP..............................8L-76
BULB - INSTALLATION, FRONT FOG
LAMP..............................8L-22
BULB - INSTALLATION, FRONT LAMP....8L-27
BULB - INSTALLATION, FRONT POSITION
LAMP..............................8L-28
BULB - INSTALLATION, HEADLAMP
......8L-32
BULB - INSTALLATION, HEATER-A/C
CONTROL ILLUMINATION
..............8L-78
BULB - INSTALLATION, LICENSE PLATE
LAMP
..............................8L-45
BULB - INSTALLATION, READING LAMP
. . . 8L-79
BULB - INSTALLATION, REAR LAMP
.....8L-59BULB - INSTALLATION, REPEATER LAMP . . 8L-60
BULB - INSTALLATION, TRANSMISSION
RANGE INDICATOR ILLUMINATION.......8L-83
BULB - INSTALLATION, VANITY LAMP....8L-84
BULB - REMOVAL, ASH RECEIVER LAMP . . 8L-71
BULB - REMOVAL, CARGO LAMP........8L-72
BULB - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-18
BULB - REMOVAL, COMPASS MINI-TRIP
ILLUMINATION......................8L-74
BULB - REMOVAL, COURTESY LAMP.....8L-75
BULB - REMOVAL, FRONT FOG LAMP....8L-21
BULB - REMOVAL, FRONT LAMP........8L-26
BULB - REMOVAL, FRONT POSITION
LAMP..............................8L-28
BULB - REMOVAL, HEADLAMP..........8L-31
BULB - REMOVAL, HEATER-A/C
CONTROL ILLUMINATION..............8L-78
BULB - REMOVAL, LICENSE PLATE
LAMP..............................8L-44
BULB - REMOVAL, READING LAMP......8L-79
BULB - REMOVAL, REAR LAMP.........8L-58
BULB - REMOVAL, REPEATER LAMP.....8L-60
BULB - REMOVAL, TRANSMISSION
RANGE INDICATOR ILLUMINATION.......8L-82
BULB - REMOVAL, VANITY LAMP........8L-83
BUMPER - INSTALLATION, JOUNCE.......2-19
BUMPER - REMOVAL, JOUNCE...........2-19
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF................21-125
BUSHING - NV3550 - INSTALLATION,
EXTENSION HOUSING.................21-74
BUSHING - NV3550 - REMOVAL,
EXTENSION HOUSING.................21-73
BUSHINGS - INSTALLATION, STABILIZER
BAR.................................2-9
BUSHINGS - REMOVAL, STABILIZER BAR . . . 2-9
BUSHINGS, AND BALL JOINT -
DESCRIPTION, UPPER SUSPENSION
ARM ...............................2-20
BUSHINGS, AND BALL JOINT -
OPERATION, UPPER SUSPENSION
ARM ...............................2-20
CABLE - ADJUSTMENTS, GEARSHIFT....21-130
CABLE - ADJUSTMENTS, PARK-
INTERLOCK........................21-154
CABLE - DESCRIPTION.................8P-3
CABLE - DESCRIPTION, ANTENNA BODY . . . 8A-4
CABLE - DIAGNOSIS AND TESTING,
ANTENNA BODY......................8A-5
CABLE - DIAGNOSIS AND TESTING,
GEARSHIFT........................21-128
CABLE - INSTALLATION, ANTENNA BODY . . 8A-6
CABLE - INSTALLATION, GEARSHIFT....21-129
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA......................8A-8
CABLE - INSTALLATION, LATCH RELEASE . 23-120
CABLE - INSTALLATION, PARK -
INTERLOCK........................21-153
CABLE - INSTALLATION, THROTTLE
CONTROL..........................14-46
CABLE - OPERATION...................8P-3
CABLE - OPERATION, ANTENNA BODY.....8A-5
CABLE - REMOVAL, ANTENNA BODY......8A-6
CABLE - REMOVAL, GEARSHIFT........21-128
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-7
CABLE - REMOVAL, LATCH RELEASE....23-120
CABLE - REMOVAL, PARK - INTERLOCK . 21-153
CABLE - REMOVAL, THROTTLE
CONTROL..........................14-45
CABLE RESISTANCE, 2.4L - SPARK PLUG . . . 8I-3
CABLES - DESCRIPTION, BATTERY.......8F-18
CABLES - DIAGNOSIS AND TESTING,
BATTERY...........................8F-19
CABLES - INSTALLATION...............5-30
CABLES - OPERATION, BATTERY........8F-18
CABLES - REMOVAL...................5-30
CALIBRATION - STANDARD PROCEDURE,
COMPASS...........................8M-2
CALIPER ADAPTER - INSTALLATION,
DISC BRAKE.........................5-18
CALIPER ADAPTER - REMOVAL, DISC
BRAKE
..............................5-18
CALIPERS - ASSEMBLY, DISC BRAKE
......5-16
CALIPERS - CLEANING, DISC BRAKE
......5-16
CALIPERS - DESCRIPTION, DISC BRAKE
. . . 5-13
CALIPERS - DISASSEMBLY, DISC BRAKE
. . . 5-14CALIPERS - INSPECTION, DISC BRAKE....5-16
CALIPERS - INSTALLATION, DISC BRAKE . . . 5-17
CALIPERS - OPERATION, DISC BRAKE.....5-14
CALIPERS - REMOVAL, DISC BRAKE......5-14
CAMBER AND CASTER ADJUSTMENT -
STANDARD PROCEDURE.................2-5
CAMBER, CASTER AND TOE
ADJUSTMENT - STANDARD
PROCEDURE..........................2-5
CAMSHAFT(S) - DESCRIPTION.......9-23,9-33
CAMSHAFT(S) - INSTALLATION......9-25,9-33
CAMSHAFT(S) - REMOVAL..........9-24,9-33
CANISTER - DESCRIPTION, VAPOR......25-33
CANISTER - INSTALLATION, VAPOR......25-33
CANISTER - OPERATION, VAPOR........25-33
CANISTER - REMOVAL, VAPOR..........25-33
CAP - CLEANING, RADIATOR PRESSURE . . . 7-25
CAP - DESCRIPTION, FUEL FILLER.......25-27
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-25
CAP - DIAGNOSIS AND TESTING,
RADIATOR PRESSURE.................7-25
CAP - INSPECTION, RADIATOR
PRESSURE..........................7-25
CAP - INSTALLATION, INSTRUMENT
PANEL END........................23-153
CAP - OPERATION, FUEL FILLER........25-27
CAP - OPERATION, RADIATOR
PRESSURE..........................7-25
CAP - REMOVAL, INSTRUMENT PANEL
END ..............................23-153
CAPACITIES - SPECIFICATIONS, FLUID......0-4
CAPACITOR - DESCRIPTION, IGNITION
COIL...............................8I-16
CAPACITOR - INSTALLATION, IGNITION
COIL...............................8I-16
CAPACITOR - OPERATION, IGNITION
COIL...............................8I-16
CAPACITOR - REMOVAL, IGNITION COIL . . . 8I-16
CAPACITY - SPECIFICATIONS, CHARGE . . . 24-42
CAPACITY TEST - DIAGNOSIS AND
TESTING, FUEL PUMP.................14-15
CARDAN UNIVERSAL JOINTS -
ASSEMBLY, SINGLE.....................3-9
CARDAN UNIVERSAL JOINTS -
DISASSEMBLY, SINGLE..................3-8
CARGO LAMP BULB - INSTALLATION.....8L-73
CARGO LAMP BULB - REMOVAL........8L-72
CARGO LAMP SWITCH - INSTALLATION . . 8L-74
CARGO LAMP SWITCH - REMOVAL......8L-73
CARGO LAMP UNIT - INSTALLATION.....8L-74
CARGO LAMP UNIT - REMOVAL.........8L-74
CARPETS AND FLOOR MATS -
INSTALLATION......................23-158
CARPETS AND FLOOR MATS - REMOVAL . 23-158
CASE - NV231 - ASSEMBLY, TRANSFER . . 21-194
CASE - NV231 - CLEANING, TRANSFER . . 21-190
CASE - NV231 - DESCRIPTION,
TRANSFER............................0-3
CASE - NV231 - DESCRIPTION,
TRANSFER.........................21-178
CASE - NV231 - DIAGNOSIS AND
TESTING, TRANSFER.................21-180
CASE - NV231 - DISASSEMBLY,
TRANSFER.........................21-182
CASE - NV231 - INSPECTION, TRANSFER . 21-190
CASE - NV231 - INSTALLATION,
TRANSFER.........................21-205
CASE - NV231 - OPERATION, TRANSFER
. 21-179
CASE - NV231 - REMOVAL, TRANSFER
. . 21-181
CASE - NV242 - ASSEMBLY, TRANSFER
. . 21-230
CASE - NV242 - CLEANING, TRANSFER
. . 21-227
CASE - NV242 - DESCRIPTION,
TRANSFER
............................0-3
CASE - NV242 - DESCRIPTION,
TRANSFER
.........................21-215
CASE - NV242 - DIAGNOSIS AND
TESTING, TRANSFER
.................21-216
CASE - NV242 - DISASSEMBLY,
TRANSFER
.........................21-218
CASE - NV242 - INSPECTION, TRANSFER
. 21-228
CASE - NV242 - INSTALLATION,
TRANSFER
.........................21-243
CASE - NV242 - OPERATION, TRANSFER
. 21-215
CASE - NV242 - REMOVAL, TRANSFER
. . 21-217
CASE BEARINGS - INSTALLATION,
DIFFERENTIAL
...............3-110,3-44,3-79
4 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

ADJUSTER (TAPPET) NOISE DIAGNOSIS
- DIAGNOSIS AND TESTING, LASH........9-28
ADJUSTMENT, FRONT FOG LAMP UNIT . . . 8L-25
ADJUSTMENT, HEADLAMP UNIT.........8L-42
AIMING - STANDARD PROCEDURE,
LAMP BAR..........................8L-65
ARM BUSHING - INSTALLATION, LOWER
CONTROL............................2-3
ARM BUSHING - INSTALLATION, LOWER
SUSPENSION..........................2-8
ARM BUSHING - INSTALLATION, UPPER
SUSPENSION..........................2-8
ARM BUSHING - REMOVAL, LOWER
CONTROL............................2-2
ARM BUSHING - REMOVAL, LOWER
SUSPENSION..........................2-7
ARM BUSHING - REMOVAL, UPPER
SUSPENSION..........................2-7
ARM BUSHINGS - INSTALLATION,
UPPER CONTROL......................2-4
ARM BUSHINGS - REMOVAL, UPPER
CONTROL............................2-3
ARMS - INSPECTION, ROCKER...........9-30
ARMS - INSTALLATION, ROCKER.........9-30
ARMS - REMOVAL, ROCKER.............9-29
ASSEMBLY - INSTALLATION, ENGINE......9-12
ASSEMBLY - REMOVAL, ENGINE.........9-12
ASSEMBLY, OIL PUMP.................9-50
BACKUP LAMP SWITCH - DESCRIPTION . . 8L-15
BACKUP LAMP SWITCH - DIAGNOSIS
AND TESTING.........................8L-15
BACKUP LAMP SWITCH - OPERATION....8L-15
BALANCE SHAFT - DESCRIPTION.........9-59
BALANCE SHAFT - OPERATION...........9-59
BALANCE SHAFT - REMOVAL............9-60
BALANCE SHAFT CARRIER -
INSTALLATION........................9-64
BALANCE SHAFT CARRIER - REMOVAL....9-64
BALANCE SHAFT CHAIN - INSTALLATION . . . 9-64
BALANCE SHAFT CHAIN - REMOVAL......9-64
BALANCE SHAFT TIMING, INSTALLATION . . . 9-61
BALL JOINT - INSTALLATION, LOWER......2-5
BALL JOINT - INSTALLATION, UPPER......2-6
BALL JOINT - REMOVAL, LOWER..........2-5
BALL JOINT - REMOVAL, UPPER..........2-6
BAR - DESCRIPTION, LAMP............8L-65
BAR - DIAGNOSIS AND TESTING, LAMP . . 8L-65
BAR - INSTALLATION, LAMP............8L-66
BAR - OPERATION, LAMP..............8L-65
BAR - REMOVAL, LAMP...............8L-65
BAR AIMING - STANDARD PROCEDURE,
LAMP..............................8L-65
BAR SWITCH - DESCRIPTION, LAMP.....8L-67
BAR SWITCH - INSTALLATION, LAMP....8L-67
BAR SWITCH - REMOVAL, LAMP........8L-67
BEAM RELAY - DESCRIPTION,
HEADLAMP HIGH....................8L-33
BEAM RELAY - DESCRIPTION,
HEADLAMP LOW.....................8L-39
BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP HIGH............8L-34
BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP LOW.............8L-40
BEAM RELAY - INSTALLATION,
HEADLAMP HIGH
....................8L-35
BEAM RELAY - INSTALLATION,
HEADLAMP LOW
.....................8L-41
BEAM RELAY - OPERATION, HEADLAMP
HIGH
..............................8L-33
BEAM RELAY - OPERATION, HEADLAMP
LOW
..............................8L-39
BEAM RELAY - REMOVAL, HEADLAMP
HIGH
..............................8L-34
BEAM RELAY - REMOVAL, HEADLAMP
LOW
..............................8L-40
BEARING - FITTING - STANDARD
PROCEDURE, MAIN
....................9-35
BEARING CLEARANCE USING
PLASTIGAGE - STANDARD
PROCEDURE, MEASURING
..............9-11
BELT - INSTALLATION, TIMING
...........9-56
BELT - REMOVAL, TIMING
..............9-55
BELT COVER(S) - INSTALLATION,
TIMING
.............................9-53
BELT COVER(S) - REMOVAL, TIMING
......9-53
BELT DIAGNOSIS - DIAGNOSIS AND
TESTING, SERPENTINE DRIVE
...........7-15BELT TENSIONER & PULLEY -
INSTALLATION, TIMING.................9-59
BELT TENSIONER & PULLEY -
REMOVAL, TIMING....................9-59
BLOCK - DESCRIPTION, ENGINE..........9-30
BLOCK HEATER - 2.4L - DESCRIPTION,
ENGINE.............................7-20
BLOCK HEATER - 2.4L - OPERATION,
ENGINE.............................7-20
BORE FITTING - STANDARD
PROCEDURE, PISTON TO CYLINDER......9-30
BORE HONING - STANDARD
PROCEDURE, CYLINDER................9-31
BRACKET BUSHING - INSTALLATION,
CLEVIS..............................2-4
BRACKET BUSHING - REMOVAL, CLEVIS....2-2
BRAKE LAMP SWITCH - DESCRIPTION . . . 8L-16
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-17
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-18
BRAKE LAMP SWITCH - OPERATION.....8L-16
BRAKE LAMP SWITCH - REMOVAL......8L-17
BULB - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP................8L-19
BULB - INSTALLATION, FRONT FOG
LAMP..............................8L-22
BULB - INSTALLATION, FRONT LAMP....8L-27
BULB - INSTALLATION, FRONT POSITION
LAMP..............................8L-28
BULB - INSTALLATION, HEADLAMP......8L-32
BULB - INSTALLATION, LICENSE PLATE
LAMP..............................8L-45
BULB - INSTALLATION, REAR LAMP.....8L-59
BULB - INSTALLATION, REPEATER LAMP . . 8L-60
BULB - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-18
BULB - REMOVAL, FRONT FOG LAMP....8L-21
BULB - REMOVAL, FRONT LAMP........8L-27
BULB - REMOVAL, FRONT POSITION
LAMP..............................8L-28
BULB - REMOVAL, HEADLAMP..........8L-30
BULB - REMOVAL, LICENSE PLATE
LAMP..............................8L-44
BULB - REMOVAL, REAR LAMP.........8L-59
BULB - REMOVAL, REPEATER LAMP.....8L-60
BUSHING - INSTALLATION, CLEVIS
BRACKET.............................2-4
BUSHING - INSTALLATION, LOWER
CONTROL ARM........................2-3
BUSHING - INSTALLATION, LOWER
SUSPENSION ARM.....................2-8
BUSHING - INSTALLATION, UPPER
SUSPENSION ARM.....................2-8
BUSHING - REMOVAL, CLEVIS BRACKET....2-2
BUSHING - REMOVAL, LOWER CONTROL
ARM ................................2-2
BUSHING - REMOVAL, LOWER
SUSPENSION ARM.....................2-7
BUSHING - REMOVAL, UPPER
SUSPENSION ARM.....................2-7
BUSHINGS - INSTALLATION, UPPER
CONTROL ARM........................2-4
BUSHINGS - REMOVAL, UPPER
CONTROL ARM........................2-3
CAMSHAFT END-PLAY - STANDARD
PROCEDURE.........................9-23
CAMSHAFT OIL SEAL(S) - INSTALLATION . . 9-22
CAMSHAFT OIL SEAL(S) - REMOVAL......9-22
CAMSHAFT(S) - CLEANING..............9-24
CAMSHAFT(S) - DESCRIPTION...........9-23
CAMSHAFT(S) - INSPECTION............9-25
CAMSHAFT(S) - INSTALLATION..........9-25
CAMSHAFT(S) - OPERATION.............9-23
CAMSHAFT(S) - REMOVAL..............9-24
CAP - CLEANING, RADIATOR PRESSURE . . . 7-25
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-25
CAP - DIAGNOSIS AND TESTING,
RADIATOR PRESSURE.................7-25
CAP - INSPECTION, RADIATOR
PRESSURE..........................7-25
CAP - OPERATION, RADIATOR
PRESSURE
..........................7-25
CARRIER - INSTALLATION, BALANCE
SHAFT
..............................9-64
CARRIER - REMOVAL, BALANCE SHAFT
....9-64
CATALYTIC CONVERTER - DESCRIPTION
. . . 11-2
CATALYTIC CONVERTER - INSPECTION
....11-3CATALYTIC CONVERTER - INSTALLATION . . . 11-3
CATALYTIC CONVERTER - REMOVAL......11-2
CENTER HIGH MOUNTED STOP LAMP
BULB - INSTALLATION................8L-19
CENTER HIGH MOUNTED STOP LAMP
BULB - REMOVAL....................8L-18
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION.................8L-19
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL....................8L-19
CHAIN - INSTALLATION, BALANCE
SHAFT..............................9-64
CHAIN - REMOVAL, BALANCE SHAFT......9-64
CHANGE - STANDARD PROCEDURE,
ENGINE OIL AND FILTER................9-47
CHART - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIAGNOSIS............7-5
CHECK, STANDARD PROCEDURE -
ENGINE OIL LEVEL....................9-47
CHECKING - DIAGNOSIS AND TESTING,
ENGINE OIL PRESSURE................9-46
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-2
CLAMPS - DESCRIPTION, HOSE...........7-1
CLAMPS - OPERATION, HOSE.............7-2
CLEANING, CAMSHAFT(S)...............9-24
CLEANING, CYLINDER HEAD.............9-20
CLEANING, CYLINDER HEAD COVER......9-26
CLEANING, EXHAUST MANIFOLD.........9-53
CLEANING, INTAKE/EXHAUST VALVES &
SEATS................................9-27
CLEANING, OIL PUMP..................9-49
CLEANING, RADIATOR.................7-24
CLEANING, RADIATOR PRESSURE CAP....7-25
CLEANING, REMOVAL..................9-55
CLEANING, STANDARD PROCEDURE......9-31
CLEARANCE USING PLASTIGAGE -
STANDARD PROCEDURE, MEASURING
BEARING............................9-11
CLEVIS BRACKET BUSHING -
INSTALLATION.........................2-4
CLEVIS BRACKET BUSHING - REMOVAL....2-2
COLLAR - INSTALLATION, STRUCTURAL . . . 9-44
COLLAR - REMOVAL, STRUCTURAL.......9-44
COMBINATION FLASHER - DESCRIPTION . . 8L-19
COMBINATION FLASHER - OPERATION . . . 8L-19
COMBUSTION PRESSURE LEAKAGE
TEST - DIAGNOSIS AND TESTING,
CYLINDER............................9-3
COMPRESSION PRESSURE TEST -
DIAGNOSIS AND TESTING, CYLINDER......9-3
CONNECTING ROD - DESCRIPTION,
PISTON.............................9-40
CONNECTING ROD - INSTALLATION,
PISTON.............................9-41
CONNECTING ROD - OPERATION,
PISTON.............................9-40
CONNECTING ROD - REMOVAL, PISTON . . . 9-40
CONNECTING ROD, FITTING.............9-32
CONNECTOR - INSTALLATION, TRAILER
TOW ..............................8L-61
CONNECTOR - REMOVAL, TRAILER TOW . . 8L-61
CONTAINER - DESCRIPTION, COOLANT
RECOVERY PRESS....................7-20
CONTAINER - OPERATION, COOLANT
RECOVERY PRESS....................7-20
CONTROL ARM BUSHING -
INSTALLATION, LOWER.................2-3
CONTROL ARM BUSHING - REMOVAL,
LOWER..............................2-2
CONTROL ARM BUSHINGS -
INSTALLATION, UPPER..................2-4
CONTROL ARM BUSHINGS - REMOVAL,
UPPER...............................2-3
CONVERTER - DESCRIPTION, CATALYTIC . . . 11-2
CONVERTER - INSPECTION, CATALYTIC....11-3
CONVERTER - INSTALLATION, CATALYTIC . . 11-3
CONVERTER - REMOVAL, CATALYTIC......11-2
COOLANT - DESCRIPTION, ENGINE.......7-19
COOLANT - DESCRIPTION, HOAT
.........7-18
COOLANT RECOVERY PRESS
CONTAINER - DESCRIPTION
.............7-20
COOLANT RECOVERY PRESS
CONTAINER - OPERATION
...............7-20
COOLANT TEMPERATURE SENSOR -
DESCRIPTION, ENGINE
.................7-21
COOLANT TEMPERATURE SENSOR -
INSTALLATION, ENGINE
................7-22
KJINDEX 1
Description Group-Page Description Group-Page Description Group-Page

ENGINE CORE AND OIL GALLERY PLUGS
- STANDARD PROCEDURE...............9-9
ENGINE DIAGNOSIS - PERFORMANCE -
DIAGNOSIS AND TESTING...............9-5
ENGINE GASKET SURFACE
PREPARATION - STANDARD
PROCEDURE.........................9-11
ENGINE MECHANICAL - DIAGNOSIS AND
TESTING.............................9-7
ENGINE MOUNTING - DESCRIPTION......9-44
ENGINE OIL AND FILTER CHANGE -
STANDARD PROCEDURE................9-47
ENGINE OIL LEAK INSPECTION -
DIAGNOSIS AND TESTING...............9-4
ENGINE OIL LEVEL CHECK, STANDARD
PROCEDURE.........................9-47
ENGINE OIL PRESSURE CHECKING -
DIAGNOSIS AND TESTING..............9-46
ENGINE, SPECIAL TOOLS - 2.4L..........9-17
EXHAUST MANIFOLD - CLEANING........9-53
EXHAUST MANIFOLD - DESCRIPTION.....9-53
EXHAUST MANIFOLD - INSPECTION.......9-53
EXHAUST MANIFOLD - INSTALLATION.....9-53
EXHAUST MANIFOLD - OPERATION.......9-53
EXHAUST MANIFOLD - REMOVAL.........9-53
EXHAUST SYSTEM - DESCRIPTION.......11-1
EXHAUST SYSTEM - DIAGNOSIS AND
TESTING............................11-2
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - DIAGNOSIS AND TESTING,
LAMPS/LIGHTING.....................8L-7
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-5
EXTERIOR - SPECIFICATIONS,
LAMPS/LIGHTING....................8L-15
FAN - ELECTRIC - DESCRIPTION,
RADIATOR...........................7-26
FAN - ELECTRIC - INSTALLATION,
RADIATOR...........................7-27
FAN - ELECTRIC - OPERATION,
RADIATOR...........................7-26
FAN - ELECTRIC - REMOVAL, RADIATOR . . . 7-26
FILTER - DESCRIPTION, OIL.............9-47
FILTER - INSTALLATION, OIL............9-47
FILTER - REMOVAL, OIL................9-47
FILTER CHANGE - STANDARD
PROCEDURE, ENGINE OIL...............9-47
FITTING - CONNECTING ROD............9-32
FITTING - PISTON RING................9-42
FITTING - STANDARD PROCEDURE,
MAIN BEARING.......................9-35
FITTING - STANDARD PROCEDURE,
PISTON TO CYLINDER BORE............9-30
FLASHER - DESCRIPTION, COMBINATION . 8L-19
FLASHER - OPERATION, COMBINATION . . . 8L-19
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM - REVERSE...........7-12
FLUSHING COOLERS AND TUBES -
STANDARD PROCEDURE................7-30
FOG LAMP BULB - INSTALLATION,
FRONT.............................8L-22
FOG LAMP BULB - REMOVAL, FRONT....8L-21
FOG LAMP RELAY - DESCRIPTION,
FRONT.............................8L-22
FOG LAMP RELAY - DESCRIPTION, REAR . 8L-56
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT.....................8L-23
FOG LAMP RELAY - DIAGNOSIS AND
TESTING, REAR......................8L-57
FOG LAMP RELAY - INSTALLATION,
FRONT.............................8L-24
FOG LAMP RELAY - INSTALLATION,
REAR..............................8L-58
FOG LAMP RELAY - OPERATION, FRONT . . 8L-22
FOG LAMP RELAY - OPERATION, REAR . . . 8L-57
FOG LAMP RELAY - REMOVAL, FRONT . . . 8L-24
FOG LAMP RELAY - REMOVAL, REAR....8L-58
FOG LAMP UNIT - ADJUSTMENT, FRONT . . 8L-25
FOG LAMP UNIT - INSTALLATION,
FRONT
.............................8L-25
FOG LAMP UNIT - REMOVAL, FRONT
.....8L-24
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE
......9-10
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL
............................9-37
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL
...............................9-37FRONT FOG LAMP BULB -
INSTALLATION.......................8L-22
FRONT FOG LAMP BULB - REMOVAL.....8L-21
FRONT FOG LAMP RELAY -
DESCRIPTION.......................8L-22
FRONT FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-23
FRONT FOG LAMP RELAY -
INSTALLATION.......................8L-24
FRONT FOG LAMP RELAY - OPERATION . . 8L-22
FRONT FOG LAMP RELAY - REMOVAL....8L-24
FRONT FOG LAMP UNIT - ADJUSTMENT . . 8L-25
FRONT FOG LAMP UNIT - INSTALLATION . . 8L-25
FRONT FOG LAMP UNIT - REMOVAL.....8L-24
FRONT LAMP BULB - INSTALLATION.....8L-27
FRONT LAMP BULB - REMOVAL.........8L-27
FRONT LAMP UNIT - INSTALLATION.....8L-28
FRONT LAMP UNIT - REMOVAL.........8L-27
FRONT MOUNT - INSTALLATION..........9-44
FRONT MOUNT - REMOVAL.............9-44
FRONT POSITION LAMP BULB -
INSTALLATION.......................8L-28
FRONT POSITION LAMP BULB -
REMOVAL..........................8L-28
FRONT SUSPENSION, SPECIAL TOOLS.....2-1
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL......9-9
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD......................9-19
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE........9-11
GASKETS AND SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE...........9-10
HAZARD SWITCH - DESCRIPTION.......8L-28
HAZARD SWITCH - INSTALLATION.......8L-30
HAZARD SWITCH - OPERATION.........8L-29
HAZARD SWITCH - REMOVAL..........8L-29
HEAD - CLEANING, CYLINDER...........9-20
HEAD - DESCRIPTION, CYLINDER........9-19
HEAD - INSPECTION, CYLINDER..........9-21
HEAD - INSTALLATION, CYLINDER........9-21
HEAD - OPERATION, CYLINDER..........9-19
HEAD - REMOVAL, CYLINDER...........9-20
HEAD COVER - CLEANING, CYLINDER.....9-26
HEAD COVER - INSPECTION, CYLINDER . . . 9-26
HEAD COVER - INSTALLATION,
CYLINDER...........................9-26
HEAD COVER - REMOVAL, CYLINDER.....9-26
HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER...................9-19
HEAD OFF - INSTALLATION, CYLINDER....9-28
HEAD OFF - REMOVAL, CYLINDER........9-27
HEAD ON - INSTALLATION, CYLINDER.....9-28
HEAD ON - REMOVAL, CYLINDER........9-27
HEADLAMP BULB - INSTALLATION.......8L-32
HEADLAMP BULB - REMOVAL..........8L-30
HEADLAMP HIGH BEAM RELAY -
DESCRIPTION.......................8L-33
HEADLAMP HIGH BEAM RELAY -
DIAGNOSIS AND TESTING.............8L-34
HEADLAMP HIGH BEAM RELAY -
INSTALLATION.......................8L-35
HEADLAMP HIGH BEAM RELAY -
OPERATION.........................8L-33
HEADLAMP HIGH BEAM RELAY -
REMOVAL..........................8L-34
HEADLAMP LEVELING MOTOR -
DESCRIPTION.......................8L-35
HEADLAMP LEVELING MOTOR -
INSTALLATION.......................8L-36
HEADLAMP LEVELING MOTOR -
OPERATION.........................8L-36
HEADLAMP LEVELING MOTOR -
REMOVAL..........................8L-36
HEADLAMP LEVELING SWITCH -
DESCRIPTION.......................8L-37
HEADLAMP LEVELING SWITCH -
DIAGNOSIS AND TESTING.............8L-37
HEADLAMP LEVELING SWITCH -
INSTALLATION
.......................8L-38
HEADLAMP LEVELING SWITCH -
OPERATION
.........................8L-37
HEADLAMP LEVELING SWITCH -
REMOVAL
..........................8L-38
HEADLAMP LOW BEAM RELAY -
DESCRIPTION
.......................8L-39
HEADLAMP LOW BEAM RELAY -
DIAGNOSIS AND TESTING
.............8L-40HEADLAMP LOW BEAM RELAY -
INSTALLATION.......................8L-41
HEADLAMP LOW BEAM RELAY -
OPERATION.........................8L-39
HEADLAMP LOW BEAM RELAY -
REMOVAL..........................8L-40
HEADLAMP UNIT - ADJUSTMENT........8L-42
HEADLAMP UNIT - INSTALLATION.......8L-42
HEADLAMP UNIT - REMOVAL...........8L-41
HEAT SHIELDS - DESCRIPTION..........11-4
HEATER - 2.4L - DESCRIPTION, ENGINE
BLOCK..............................7-20
HEATER - 2.4L - OPERATION, ENGINE
BLOCK..............................7-20
HIGH BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-34
HIGH BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-35
HIGH BEAM RELAY - OPERATION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - REMOVAL,
HEADLAMP.........................8L-34
HIGH MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP BULB -
REMOVAL, CENTER...................8L-18
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER...................8L-19
HOAT COOLANT - DESCRIPTION..........7-18
HONING - STANDARD PROCEDURE,
CYLINDER BORE......................9-31
HOSE CLAMPS - DESCRIPTION...........7-1
HOSE CLAMPS - OPERATION.............7-2
HYDRAULIC LIFTERS - INSTALLATION.....9-29
HYDRAULIC LIFTERS - REMOVAL.........9-29
HYDROSTATIC LOCKED ENGINE -
STANDARD PROCEDURE.................9-9
INSPECTION - DIAGNOSIS AND
TESTING, ENGINE OIL LEAK..............9-4
INSPECTION, CAMSHAFT(S).............9-25
INSPECTION, CATALYTIC CONVERTER.....11-3
INSPECTION, CRANKSHAFT.............9-34
INSPECTION, CYLINDER HEAD...........9-21
INSPECTION, CYLINDER HEAD COVER.....9-26
INSPECTION, EXHAUST MANIFOLD.......9-53
INSPECTION, INTAKE MANIFOLD.........9-52
INSPECTION, OIL PUMP................9-50
INSPECTION, RADIATOR................7-24
INSPECTION, RADIATOR PRESSURE CAP . . . 7-25
INSPECTION, REMOVAL................9-28
INSPECTION, ROCKER ARMS............9-30
INSPECTION, STANDARD PROCEDURE.....9-32
INSPECTION, WATER PUMP - 2.4L........7-28
INSTALLATION - BALANCE SHAFT
TIMING.............................9-61
INSTALLATION, 2.4L...................7-20
INSTALLATION, 2.4L...................9-19
INSTALLATION, 2.4L ENGINE....7-14,7-17,7-22,
7-28
INSTALLATION, BALANCE SHAFT
CARRIER............................9-64
INSTALLATION, BALANCE SHAFT CHAIN . . . 9-64
INSTALLATION, BRAKE LAMP SWITCH....8L-18
INSTALLATION, CAMSHAFT OIL SEAL(S) . . . 9-22
INSTALLATION, CAMSHAFT(S)...........9-25
INSTALLATION, CATALYTIC CONVERTER
....11-3
INSTALLATION, CENTER HIGH MOUNTED
STOP LAMP BULB
....................8L-19
INSTALLATION, CENTER HIGH MOUNTED
STOP LAMP UNIT
....................8L-19
INSTALLATION, CLEVIS BRACKET
BUSHING
.............................2-4
INSTALLATION, CRANKSHAFT
............9-34
INSTALLATION, CRANKSHAFT OIL SEAL -
FRONT
..............................9-37
INSTALLATION, CRANKSHAFT OIL SEAL -
REAR
...............................9-39
INSTALLATION, CRANKSHAFT SPROCKET
. . 9-56
INSTALLATION, CROSS-OVER PIPE
.......11-4
INSTALLATION, CYLINDER HEAD
.........9-21
INSTALLATION, CYLINDER HEAD COVER
. . . 9-26
INSTALLATION, CYLINDER HEAD OFF
......9-28
INSTALLATION, CYLINDER HEAD ON
......9-28
KJINDEX 3
Description Group-Page Description Group-Page Description Group-Page

MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE.....................9-51
MEASURING BEARING CLEARANCE
USING PLASTIGAGE - STANDARD
PROCEDURE.........................9-11
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE......................9-7
MOTOR - DESCRIPTION, HEADLAMP
LEVELING..........................8L-35
MOTOR - INSTALLATION, HEADLAMP
LEVELING..........................8L-36
MOTOR - OPERATION, HEADLAMP
LEVELING..........................8L-36
MOTOR - REMOVAL, HEADLAMP
LEVELING..........................8L-36
MOUNT - INSTALLATION, FRONT.........9-44
MOUNT - INSTALLATION, REAR..........9-45
MOUNT - REMOVAL, FRONT.............9-44
MOUNT - REMOVAL, REAR..............9-45
MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP BULB -
REMOVAL, CENTER HIGH..............8L-18
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH..............8L-19
MOUNTING - DESCRIPTION, ENGINE......9-44
MUFFLER - DESCRIPTION...............11-4
MUFFLER - INSTALLATION..............11-5
MUFFLER - REMOVAL..................11-4
MULTI-FUNCTION SWITCH -
DESCRIPTION.......................8L-46
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-50
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-53
MULTI-FUNCTION SWITCH - OPERATION . . 8L-48
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-53
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, LASH ADJUSTER (TAPPET)......9-28
OFF - INSTALLATION, CYLINDER HEAD....9-28
OFF - REMOVAL, CYLINDER HEAD........9-27
OIL AND FILTER CHANGE - STANDARD
PROCEDURE, ENGINE..................9-47
OIL FILTER - DESCRIPTION.............9-47
OIL FILTER - INSTALLATION.............9-47
OIL FILTER - REMOVAL.................9-47
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE..............9-9
OIL LEAK INSPECTION - DIAGNOSIS
AND TESTING, ENGINE..................9-4
OIL LEVEL CHECK, STANDARD
PROCEDURE - ENGINE.................9-47
OIL PAN - INSTALLATION...............9-48
OIL PAN - REMOVAL...................9-48
OIL PRESSURE CHECKING - DIAGNOSIS
AND TESTING, ENGINE.................9-46
OIL PRESSURE SENSOR/SWITCH -
DESCRIPTION........................9-48
OIL PRESSURE SENSOR/SWITCH -
OPERATION..........................9-48
OIL PUMP - ASSEMBLY................9-50
OIL PUMP - CLEANING.................9-49
OIL PUMP - DISASSEMBLY.............9-49
OIL PUMP - INSPECTION...............9-50
OIL PUMP - INSTALLATION.............9-50
OIL PUMP - REMOVAL.................9-49
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT........................9-37
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT........................9-37
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT........................9-39
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT........................9-38
OIL SEAL(S) - INSTALLATION,
CAMSHAFT..........................9-22
OIL SEAL(S) - REMOVAL, CAMSHAFT.....9-22
ON-BOARD DIAGNOSTICS (OBD) -
DIAGNOSIS AND TESTING...............7-2
OPERATION, BACKUP LAMP SWITCH.....8L-15
OPERATION, BALANCE SHAFT
...........9-59
OPERATION, BRAKE LAMP SWITCH
......8L-16
OPERATION, CAMSHAFT(S)
.............9-23
OPERATION, COMBINATION FLASHER
....8L-19
OPERATION, COOLANT RECOVERY
PRESS CONTAINER
....................7-20OPERATION, COOLING SYSTEM...........7-2
OPERATION, CRANKSHAFT..............9-33
OPERATION, CYLINDER HEAD...........9-19
OPERATION, DAYTIME RUNNING LAMP
RELAY.............................8L-20
OPERATION, DESCRIPTION..............7-20
OPERATION, ENGINE BLOCK HEATER -
2.4L................................7-20
OPERATION, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
OPERATION, EXHAUST MANIFOLD........9-53
OPERATION, FRONT FOG LAMP RELAY . . . 8L-22
OPERATION, HAZARD SWITCH..........8L-29
OPERATION, HEADLAMP HIGH BEAM
RELAY.............................8L-33
OPERATION, HEADLAMP LEVELING
MOTOR............................8L-36
OPERATION, HEADLAMP LEVELING
SWITCH............................8L-37
OPERATION, HEADLAMP LOW BEAM
RELAY.............................8L-39
OPERATION, HOSE CLAMPS..............7-2
OPERATION, INTAKE MANIFOLD..........9-51
OPERATION, LAMP BAR...............8L-65
OPERATION, LAMPS/LIGHTING -
EXTERIOR...........................8L-5
OPERATION, LUBRICATION..............9-46
OPERATION, MULTI-FUNCTION SWITCH . . . 8L-48
OPERATION, OIL PRESSURE SENSOR/
SWITCH..............................9-48
OPERATION, PARK LAMP RELAY........8L-54
OPERATION, PISTON & CONNECTING
ROD................................9-40
OPERATION, RADIATOR FAN - ELECTRIC . . . 7-26
OPERATION, RADIATOR PRESSURE CAP . . . 7-25
OPERATION, REAR FOG LAMP RELAY....8L-57
OPERATION, TRAILER TOW RELAY.......8L-62
OPERATION, WATER PUMP - 2.4L........7-27
PAN - INSTALLATION, OIL...............9-48
PAN - REMOVAL, OIL..................9-48
PARK LAMP RELAY - DESCRIPTION......8L-54
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-55
PARK LAMP RELAY - INSTALLATION.....8L-56
PARK LAMP RELAY - OPERATION.......8L-54
PARK LAMP RELAY - REMOVAL.........8L-55
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-5
PIPE - INSTALLATION, CROSS-OVER......11-4
PIPE - REMOVAL, CROSS-OVER..........11-4
PISTON & CONNECTING ROD -
DESCRIPTION........................9-40
PISTON & CONNECTING ROD -
INSTALLATION........................9-41
PISTON & CONNECTING ROD -
OPERATION..........................9-40
PISTON & CONNECTING ROD -
REMOVAL...........................9-40
PISTON RING, FITTING.................9-42
PISTON TO CYLINDER BORE FITTING -
STANDARD PROCEDURE................9-30
PLASTIGAGE - STANDARD PROCEDURE,
MEASURING BEARING CLEARANCE
USING..............................9-11
PLATE LAMP BULB - INSTALLATION,
LICENSE...........................8L-45
PLATE LAMP BULB - REMOVAL,
LICENSE...........................8L-44
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-46
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-45
PLAY - STANDARD PROCEDURE,
CRANKSHAFT END....................9-33
PLUGS - STANDARD PROCEDURE,
ENGINE CORE AND OIL GALLERY.........9-9
POSITION LAMP BULB - INSTALLATION,
FRONT.............................8L-28
POSITION LAMP BULB - REMOVAL,
FRONT
.............................8L-28
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING
.........................7-2
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE
............................9-11
PRESS CONTAINER - DESCRIPTION,
COOLANT RECOVERY
..................7-20
PRESS CONTAINER - OPERATION,
COOLANT RECOVERY
..................7-20PRESSURE CAP - CLEANING, RADIATOR . . . 7-25
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-25
PRESSURE CAP - DIAGNOSIS AND
TESTING, RADIATOR...................7-25
PRESSURE CAP - INSPECTION,
RADIATOR...........................7-25
PRESSURE CAP - OPERATION,
RADIATOR...........................7-25
PRESSURE CHECKING - DIAGNOSIS AND
TESTING, ENGINE OIL..................9-46
PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION.........................9-3
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-48
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-48
PRESSURE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMPRESSION.......9-3
PULLEY - INSTALLATION, TIMING BELT
TENSIONER..........................9-59
PULLEY - REMOVAL, TIMING BELT
TENSIONER..........................9-59
PUMP - 2.4L - DESCRIPTION, WATER.....7-27
PUMP - 2.4L - INSPECTION, WATER......7-28
PUMP - 2.4L - OPERATION, WATER.......7-27
PUMP - ASSEMBLY, OIL................9-50
PUMP - CLEANING, OIL................9-49
PUMP - DISASSEMBLY, OIL.............9-49
PUMP - INSPECTION, OIL...............9-50
PUMP - INSTALLATION, OIL.............9-50
PUMP - REMOVAL, OIL.................9-49
RADIATOR - CLEANING.................7-24
RADIATOR - DESCRIPTION..............7-22
RADIATOR - INSPECTION...............7-24
RADIATOR - INSTALLATION.............7-24
RADIATOR - REMOVAL.................7-22
RADIATOR FAN - ELECTRIC -
DESCRIPTION........................7-26
RADIATOR FAN - ELECTRIC -
INSTALLATION........................7-27
RADIATOR FAN - ELECTRIC -
OPERATION..........................7-26
RADIATOR FAN - ELECTRIC - REMOVAL . . . 7-26
RADIATOR PRESSURE CAP - CLEANING . . . 7-25
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-25
RADIATOR PRESSURE CAP - DIAGNOSIS
AND TESTING........................7-25
RADIATOR PRESSURE CAP -
INSPECTION.........................7-25
RADIATOR PRESSURE CAP - OPERATION . . 7-25
REAR - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-39
REAR - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-38
REAR FOG LAMP RELAY - DESCRIPTION . . 8L-56
REAR FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-57
REAR FOG LAMP RELAY -
INSTALLATION.......................8L-58
REAR FOG LAMP RELAY - OPERATION . . . 8L-57
REAR FOG LAMP RELAY - REMOVAL.....8L-58
REAR LAMP BULB - INSTALLATION......8L-59
REAR LAMP BULB - REMOVAL..........8L-59
REAR LAMP UNIT - INSTALLATION......8L-60
REAR LAMP UNIT - REMOVAL..........8L-59
REAR MOUNT - INSTALLATION..........9-45
REAR MOUNT - REMOVAL..............9-45
REAR SUSPENSION, SPECIAL TOOLS......2-6
RECOVERY PRESS CONTAINER -
DESCRIPTION, COOLANT...............7-20
RECOVERY PRESS CONTAINER -
OPERATION, COOLANT.................7-20
REFILLING COOLING SYSTEM -
STANDARD PROCEDURE................7-11
RELAY - DESCRIPTION, DAYTIME
RUNNING LAMP.....................8L-20
RELAY - DESCRIPTION, FRONT FOG
LAMP..............................8L-22
RELAY - DESCRIPTION, HEADLAMP
HIGH BEAM
.........................8L-33
RELAY - DESCRIPTION, HEADLAMP LOW
BEAM
..............................8L-39
RELAY - DESCRIPTION, PARK LAMP
.....8L-54
RELAY - DESCRIPTION, REAR FOG LAMP
. 8L-56
RELAY - DESCRIPTION, TRAILER TOW
....8L-62
KJINDEX 5
Description Group-Page Description Group-Page Description Group-Page